Statewaterheaters SCGSS01108 User Manual
COMMERCIAL
FORCE™90+
96% Efficient
Power Direct Vent Commercial Gas Water Heaters
The 100,000 BTU Force™90+ light-duty commercial gas water heater is equipped with a fully submerged, spiral-shaped condensing heat exchanger and 50 gallons of storage capacity. This design provides much greater heat transfer surface than a standard straight flue tube, resulting in
96% thermal efficiency and higher hot water output than comparable 80% efficient water heaters. With a 22˝ diameter, the Force™ 90+ can be
installed in less space than a 75-gallon unit yet delivers greater recovery and lower operating costs. The Force 90 is ENERGY STAR® Qualified.
Power Direct Vent Design for Installation Versatility
• Modular blower, with 120V, 60Hz electrical system (5 amps or less)
• Can be vented vertically thru-the-roof or horizontally thru-the wall.
Vents using PVC, CPVC or ABS pipe.
2˝ pipe allows vent runs up to 45 equivalent feet
3˝ pipe allows vent runs up to 128 equivalent feet
• Optional concentric vent and sidewall termination kits available
Available in Natural Gas or Propane
Side-Mounted Taps for Recirculating Systems
• Hot and cold “side taps” allow the Force™ 90+ to be used for “combination” systems
for water heating plus space heating, radiant floor heating or other applications
requiring a recirculating hot water loop
• Plugs for recirculating taps are factory installed
Advanced Electronic Control
• Large LCD display
• Precise temperature control
• Advanced diagnostics
• iCOMM™ Compatible and can be monitored from remote locations.
Call 1.888.WATER02 for more information.
Glasslined Tank with Two Magnesium Anode Rods
• Provides superior protection against corrosion
• Commercial-grade glass lining protects all “water side” tank surfaces plus inside of internal
heat exchanger exposed to condensate
Top-Fired Low NOx Burner
• Reduces NOx emissions and complies with SCAQMD Rule 1146.2, and other Air Quality Management
Districts with similar requirements for low NOx emissions
CSA Certified and ASME Rated T&P Relief Valve
Maximum Hydrostatic Working Pressure: 150 psi
Meets the thermal efficiency and standby
loss requirements of the U.S. Department
of Energy and current edition of
ASHRAE/IESNA 90.1
Low Lead Content
Series 124/125
SCGSS01108 Revised May 2012
Three-Year Limited Tank Warranty
• Consult written warranty shipped with water heater or contact State Water Heater
for complete warranty information
FORCE™90+
96% Efficient
Power Direct Vent Commercial Gas Water Heaters
SPECIFICATIONS
BTU
MODEL
NUMBER
SHE50 100NE 100,000 50 291 116 83 255
All models–Maximum Supply Pressure: 14 inches w.c. (3.48 kPa) Minimum Supply Pressure Natural Gas: 3.5 inches w.c.
(.87 kPa). Minimum Pressure Propane: 8.0 inches w.c. (1.99 kPa). Minimum Pressure must be maintained under both load and no-load (static and dynamic)
conditions.
INPUT
PER
HOUR
TAN K
SIZE
GALLONS
40ºF 100ºF 140ºF
RECOVERY–GALLONS
PER HOUR
AT DEGREE RISE
SHIPPING
WEIGHT
LBS.
DIMENSIONS
SHE50 100NE A B C D E F
INCHES 66-3/4 49-1/4 22 15-3/4 3 8
Top inlet and outlet: 3/4˝ male NPT
Side inlet and outlet: 3/4˝ female NPT
Gas inlet: 1/2˝ NPT
Optional Concentric Vent Kit Part # 900391010 5
*INSTALL IN ACCORDANCE WITH LOCAL CODES.
(Natural or Propane) gas water heater(s) shall be State Force™ 90+ model SHE50 100NE, with 96% thermal efficiency, a storage capacity of 50 gallons, an input rating of 100,000 BTU per hour, a recovery
rating of 116 gallons per hour at 100ºF rise and a maximum hydrostatic working pressure of 150 psi. Water heater(s) shall be of power direct vent design, using 2 or 3˝ PVC, CPVC or ABS pipe for horizontal and/or
vertical vent runs. Water heater(s) shall have: 1: Glasslined steel tank construction and a spiral-shaped heat exchanger placed entirely inside the tank, which shall be glasslined on the flue gas side to
protect against acidic condensate. 2: Advanced electronic control with large LCD display and advanced diagnostics. Water heaters shall incorporae the iCOMM
fault alert. 3: A 3-year limited warranty against tank leaks. Water heater(s) shall meet the thermal efficiency and standby loss requirements of the U.S. Department of Energy and current edition of
ASHRAE/IESNA 90.1.
SUGGESTED SPECIFICATION
™
system for remote monitoring, leak detection and
For complete information on limited warranties, consult written warranty
or contact the State Customer Care Center at 1-800-365-0024.
State Industries, Inc. reserves the right to make product changes or improvements without prior notice.
For more information on State Water Heaters, contact:
State Water Heaters
500 Tennessee Waltz Parkway
Ashland City, TN 37015
800-365-0024 Toll-free USA
www.statewaterheaters.com
Revised June 2013
SCGSS01108
Loading...