State Industries Self-Cleaning Commercial Gas Water Heaters User Manual

COMMERCIAL

BOOSTER

S ANDBLASTER

MODELS

Self-Cleaning Commercial Gas Water Heaters

Sandblaster® Booster commercial gas water heaters are designed to provide high temperature water (usually 180ºF) to commercial dishwashers. In these applications, the booster water heater is installed in conjunction with a standard water heater, which delivers lower-temperature water to serve the non-dishwashing needs of a restaurant or other foodservice application.

™

Self-Cleaning Device

SANDBLASTER

State Hydro Cannon

• Significantly reduces buildup of lime, sand and other sediment in the tank

• Helps water heaters retain their rated efficiency longer and last longer, with low water heating costs

Induced-Draft Design

• Built-in blower produces power-induced draft of makeup air prior to burner ignition, for more efficient control of heat through the flue collector

• Eliminates performance problems caused by negative indoor air pressure

• Requires no draft hood or barometric damper

Rated as Category 1 Appliance

• Can be commonly vented with other Category 1 appliances, using standard metal type “B” vent

Multiple Anode Rods

• Protects tank from corrosion

Three Water Connection Options

• Hot and cold water connections can be made through top, front or rear of water heater

• Hydro Cannon device operates when front cold water connection is used

Intermittent Electronic Ignition

• Provides flame failure response in less than one second

• Includes power ON/OFF switch

• Eliminates standing pilot

Factory-installed Temperature and Pressure Relief Valve

Maximum Hydrostatic Working Pressure: 160 psi

80% Thermal Efficiency

Meets ASHRAE/IESNA 90.1-1999

• Also, design-certified by CSA International, according to to ANS Z21.10.3 standards governing storage-type water heaters

For more Information on the Sandblaster® contact: State Water Heaters 500 Tennessee Waltz Parkway, Ashland City, TN 37015

800-365 0024 Toll-free USA www.statewaterheaters.com

SCGSS00105 July 2007R

For more Information on the SandBlaster® contact: State Water Heaters 500 Tennessee Waltz Parkway, Ashland City, TN 37015

800-365-0024 Toll-free www.statewaterheaters.com

For complete information on limited warranties, consult written warranty, or contact the State Customer Care Center, 1-800-365-0024.

State Industries reserves the right to make product changes or improvements without prior notice.

SANDBLASTER

Self-Cleaning Commercial Gas Water Heaters

MODEL

NUMBER

GAL

CAP.

INPUT

PER

HOUR

NATURAL/

PROPANE

FIRST HOUR

RATING

100°F

RISE

40° 100° 140°

SBD30 150 NE 32 150,000 167 364 145 104

SBD30 199 NE 32 199,000 216 485 194 139

RECOVERY – GALLONS

PER HOUR AT °F TEMPERATURE RISE

MODEL

NUMBER

A B C D E F G H

GAS

CONN.

WATER

CONN.

APPROX.

SHIPPING

WEIGHT

(LBS.)

SBD30 150 NE 45 40 27-3/4 32-1/4 15-3/4 5 6-1/2 6 3/4" 1-1/2" 400

SBD30 199 NE 45 40 27-3/4 32-1/4 15-3/4 5 6-1/2 6 3/4" 1-1/2" 400

DIMENSIONS AND WEIGHT

CAPACITY, INPUT AND OUTPUT

BOOSTER MODELS

1-1/2" NPI

OUTLET

1-1/2" NPI

INLET

CLEARANCE

1" NPI RELIEF

VALVE OPENING

15.2cm

1.5

3.8cm

SUGGESTED SPECIFICATION

Gas booster water heater(s) shall be State Sandblaster, Model Number ___________________, with a 32-gallon storage capacity, an input rate of __________________ BTU/HR, _________________gas, and a recovery rate of________ gallons per hour at a________ degree Fahrenheit temperature rise, and a maximum hydrostatic working pressure of 160 psi.

Unit(s) shall have a fan-assisted combustion system, providing a power-induced draft of makeup air prior to burner ignition. Unit(s) shall be equipped with intermittent electronic ignition with power on/off switch, which shall provide flame failure response in less than one second. The burner for the unit(s) shall be easily removable. Unit(s) shall be equipped with a factory-installed temperature and pressure relief valve, and a 2-

3/4" x 3-3/4" tank inspection port.

The water heater tank shall be glass-lined and protected against premature failure in the following ways:

1. Against electrolytic corrosion by multiple, factory-installed anode rods.

2.Against failure due to overheating caused by the buildup of scale, film and other sediment by a

self-cleaning device,positioned inside the tank so that it directs the flow of inlet water in such a way that microscopic particles of precipitated solids shall be kept in suspension and exhausted from the water heater on that or successive hot water draws.

Unit(s) shall meet or exceed ASHRAE/IESNA 90.1-1999, and be design-certified by CSA International, according to ANS Z21.10.3 standards governing storage-type water heaters.

DIMENSIONS IN INCHES

COMMERCIAL