How it Works
State
Loading...
TPD150 400ONEA
User Manual
6 pgs3.31 Mb0

State TPD150 400ONEA User Manual

Download
COMMERCIAL
TITAN LV
Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters
Meets or exceeds current edition of ASHRAE/IES-90.1-1999.
– TPX Low NOXmodels meet or exceed current Texas and
X
Limited Warranty Outline
– If the tank should leak any time during the first three years, under
the terms of the warranty,State Water Heaters will repair or replace heater; installation, labor, handling and local delivery extra.
– NOTE: This Outline Is NO
consult the written warranty or State Water Heaters.
T A Warranty. For complete information,
TPO – Oil Fired Models: No. 1 or 2 Oil
TPD – Dual Fuel Gas/Oil: Natural Gas or Propane & No. 1 or 2 Oil
Low NO
California SCAQMD air quality standards.
UL– Entire unit UL listed (File No. MH11631). Glass-Lined Tank – Exclusive corrosion protection with glass-
lining on all interior surfaces. Multiple anodes provide even more corrosion protection.
ASME Construction Standard – 160 PSI working pressure on all models.
Powered Gas Burner – Powered burner has electronic flame
safeguard control with intermittent spark ignition. Also included are main and pilot automatic gas valves plus gas pressure regulators, diaphragm air switch for proof of blower operation.
Fully Automatic Controls With Safety Shutoff – High
temperature limit control (manual reset). ASME rated temperature and pressure relief valve. Hinged door control compartment for ease of access. Two thermostats, upper and lower, for accurate temperature control. Standard control is for 120˚F - 180˚F water service.
Jacket And Insulation – Heavy gauge steel with baked powder coat
finish. Insulated with high-density foam insulation that meets or exceeds all required standards.
Factory Start-up Included – Required for activating warranty and
assuring maximum operating performance.
Other Features
– Two layers of high temperature ceramic fiber insulation in
combustion chamber
– Flame inspection port opening – Mounted on rugged channel iron skids – Combination temperature and pressure gauge – Low water cutoff – ASME rated temperature and pressure relief valve – Barometric draft regulator – Two cleanout inspection openings – 120 volt control circuit – Drain valve – Removable lifting lugs
Options
– Factory Mutual approved control arrangement – 5 year or 10 year limited warranty – High or low water pressure switch – 180°F water service thermostats – A.G.A. rated T & P Valve – Modular graphic burner systems management on heaters with
270,000 Btu input and over
– Combustion Air intake Adapter
For more information on State® contact: State Water Heaters 500 Tennessee Waltz Parkway, Ashland City, TN 37015
800.365.0024 Toll-free USA www.statewaterheaters.com
SCDSS00108 April 2008R Page 1 of 6 ©2008 State Water Heaters
TITAN LV
TPX Power Gas Large Volume Commercial Water Heaters
SPECIFICATIONS
Nominal
Model Number
Storage Capacity
Gallons Gas Rating 80°F Rise 100°F Rise 140°F Rise A B C D E F G H J
TPG 150 140 NEA 150 140,000 256 170 136 97 831⁄2 141⁄2 273⁄4 11⁄4 361⁄2 5 47 73 1292 TPG 150 199 NEA 150 199,000 313 241 193 138 831⁄2 141⁄2 273⁄4 11⁄4 361⁄2 6 47 73 12921⁄7 HP - 2.5 Amps TPG 150 255 NEA 150 255,000 367 359 247 176 831⁄2 141⁄2 273⁄4 11⁄4 361⁄2 6 47 73 1292 TPG 150 270 NEA 150 270,000 382 327 262 187 831⁄214 1 273⁄411⁄4361⁄26571⁄273 1397 TPG 150 400 NEA 150 400,000 507 485 387 277 831⁄2 14 1 273⁄4 11⁄4 361⁄2 7571⁄2 73 13971⁄4 HP - 4.6 Amps TPG 150 540 NEA 150 540,000 644 654 524 374 831⁄2 14 1 273⁄4 11⁄4 361⁄2 8571⁄2 73 1505 TPG 150 720 NEA 150 720,000 818 873 698 499 831⁄2 14 11⁄4 273⁄4 11⁄4 361⁄2 10 571⁄2 73 15101⁄3 HP - 5.5 Amps TPG 200 300 NEA 200 300,000 451 364 291 208 831⁄2 15 1 321⁄2 11⁄2 443⁄4 6661⁄2 73 2098 TPG 200 600 NEA 200 600,000 742 727 582 416 831⁄2 15 1 321⁄2 11⁄2 443⁄4 8661⁄2 73 2098 TPG 200 800 NEA 200 800,000 936 970 776 554 831⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 10 661⁄2 73 2103 TPG 200 1000 NEA 200 1,000,000 1130 1212 970 693 831⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 10 661⁄2 73 2103 TPG 200 1250 NEA 200 1,250,000 1372 1515 1212 866 831⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 12 661⁄2 73 2467 TPG 200 1500 NEA 200 1,500,000 1615 1818 1455 1039 831⁄215 11⁄2321⁄211⁄2443⁄412 811⁄273 2757 TPG 300 300 NEA 300 300,000 531 364 291 208 911⁄2 14 1 261⁄2 11⁄2 443⁄4 6661⁄2 83 2150 TPG 300 600 NEA 300 600,000 822 727 582 416 911⁄2 14 1 261⁄2 11⁄2 443⁄4 8661⁄2 83 2150 TPG 300 800 NEA 300 800,000 1016 970 776 554 911⁄2 14 11⁄4 261⁄2 11⁄2 443⁄4 10 661⁄2 83 2308 TPG 300 1000 NEA 300 1,000,000 1210 1212 970 693 911⁄2 14 11⁄4 261⁄2 11⁄2 443⁄4 10 661⁄2 83 2308 TPG 300 1250 NEA 300 1,250,000 1452 1515 1212 866 911⁄214 11⁄4261⁄211⁄2443⁄412 661⁄283 2584 TPG 300 1500 NEA 300 1,500,000 1695 1818 1455 1039 911⁄214 11⁄2261⁄211⁄2443⁄412 811⁄283 2774 TPG 400 600 NEA 400 600,000 902 727 582 416 911⁄2 15 1 321⁄2 2558761⁄2 81 32071⁄4 HP - 4.6 Amps TPG 400 800 NEA 400 800,000 1096 970 776 554 911⁄2 15 11⁄4 321⁄2 25510761⁄2 81 3212 TPG 400 1000 NEA 400 1,000,000 1290 1212 970 693 911⁄2 15 11⁄4 321⁄2 25510761⁄2 81 32121⁄3 HP - 5.5 Amps TPG 400 1250 NEA 400 1,250,000 1532 1515 1212 866 911⁄2 15 11⁄4 321⁄2 25512761⁄2 81 3212 TPG 400 1500 NEA 400 1,500,000 1775 1816 1455 1039 911⁄215 11⁄2321⁄225512911⁄281 3402 TPG 400 1750 NEA 400 1,750,000 2017 2121 1697 1212 911⁄2 15 2 321⁄2 25514911⁄2 81 35281⁄2 HP - 7.4 Amps TPG 400 2000 NEA 400 2,000,000 2259 2424 1939 1385 991⁄215 2 321⁄225514911⁄289 3669 TPG 500 2250 NEA 500 2,250,000 2582 2727 2182 1558 110 15 2 321⁄2 25516911⁄2 100 4277 TPG 500 2500 NEA 500 2,500,000 2824 3030 2424 1732 110 15 2 321⁄2 25516911⁄2 100 4419 TPG 600 720 NEA 600 720,000 1178 873 698 499 119 15 11⁄4321⁄225510761⁄2109 3667 TPG 600 1000 NEA 600 1,000,000 1450 1212 970 693 119 15 11⁄4 321⁄2 25510761⁄2 109 36671⁄3 HP - 5.5 Amps TPG 600 1250 NEA 600 1,250,000 1692 1515 1212 866 119 15 11⁄4 321⁄2 25512761⁄2 109 3667 TPG 600 1500 NEA 600 1,500,000 1935 1816 1455 1039 119 15 11⁄2 321⁄2 25512911⁄2 109 3837 TPG 600 1750 NEA 600 1,750,000 2177 2121 1697 1212 119 15 2 321⁄225514911⁄2109 38371⁄2HP - 7.4 Amps TPG 600 2000 NEA 600 2,000,000 2419 2424 1939 1385 119 15 2 321⁄225514911⁄2109 3837 TPG 600 2250 NEA 600 2,250,000 2662 2727 2182 1558 119 15 2 321⁄2 25516911⁄2 109 4477 TPG 600 2500 NEA 600 2,500,000 2904 3030 2424 1732 119 15 2 321⁄2 25516911⁄2 109 4619
Certified Minimum Installation Clearances to Combustibles:
Front: 18 inches Back: 0 inches Sides: 0 inches Top: 5 inches
A clearance of 24 inches should be maintained from serviceable parts such as relief valve, power burner, drain valve and anodes (anodes are located on side above cold water inlet).
Minimum gas supply pressure: 7 Inches W.C. Maximum gas supply pressure: 13 Inches W.C.
TPG models are Category I appliances (Fan Assisted) and require a negative draft. These units should only be commonly vented with other Category I negative draft appliances per the latest addition of the National Fuel Gas Code. An approved/listed Type “B” venting material is recommended. A negative draft of -0.02˝ to -0.07 is required in the vent.
TPG models are available in both natural gas and propane. To order propane, change the “N” to “P” in the model number. Example: TPG 150 140 P
EA
Input
Rating
BTU/Hr.
U.S. Natural Hour
First Recovery
Output (Gallons)
ASME
Dimensions In Inches
Ship.
Wt. Motor HP
w/Burner 120V 60 Hz 1
(lbs.)
3
3
1
⁄4 HP - 4.6 Amps
1
⁄3 HP - 5.5 Amps
1
⁄2 HP - 7.4 Amps
1
⁄4 HP - 4.6 Amps
1
⁄3HP - 5.5 Amps
1
⁄2 HP - 7.4 Amps
⁄4 HP - 10.2 Amps
⁄4HP - 10.2 Amps
SCDSS00108 April 2008R
Page 2 of 6 ©2008 State Water Heaters Company
TITAN LV
TPX Power Low NOX Large Volume Commercial Water Heaters
SPECIFICATIONS
Nominal
Model Number
T
PX 150 400 NEA 150 400,000 507 485 387 277 831⁄2 14 1 273⁄4 11⁄4 54 7 571⁄2 73 TPX 150 540 NEA 150 540,000 644 654 524 374 831⁄2 14 1 273⁄4 11⁄4 54 8 571⁄2 73 TPX 200 800 NEA 200 800,000 936 970 776 554 831⁄2 15 11⁄4 321⁄2 11⁄2 60 10 72 73 TPX 200 1000 NEA 200 1,000,000 1130 1212 970 693 831⁄2 15 11⁄4 321⁄2 11⁄2 60 10 72 73 TPX 200 1250 NEA 200 1,250,000 1372 1515 1212 866 831⁄2 15 11⁄4 321⁄2 11⁄2 60 12 72 73 TPX 200 1500 NEA 200 1,500,000 1615 1818 1455 1039 831⁄2 15 11⁄2 321⁄2 11⁄2 60 12 72 73 TPX 300 800 NEA 300 800,000 1016 970 776 554 911⁄2 14 11⁄4 261⁄2 11⁄2 60 10 72 83 TPX 300 1000 NEA 300 1,000,000 1210 1212 970 693 911⁄2 14 11⁄4 261⁄2 11⁄2 60 10 72 83 TPX 300 1250 NEA 300 1,250,000 1452 1515 1212 866 91 TPX 300 1500 NEA 300 1,500,000 1695 1818 1455 1039 911⁄2 14 11⁄2 261⁄2 11⁄2 60 12 72 83 TPX 400 800 NEA 400 800,000 1096 970 776 554 911⁄2 15 11⁄4 321⁄2 267108481 TPX 400 1000 NEA 400 1,000,000 1290 1212 970 693 911⁄2 15 11⁄4 321⁄2 267108481 TPX 400 1250 NEA 400 1,250,000 1532 1515 1212 866 911⁄2 15 11⁄4 321⁄2 267128481 TPX 400 1500 NEA 400 1,500,000 1775 1816 1455 1039 911⁄2 15 11⁄2 321⁄2 267128481 TPX 400 1750 NEA 400 1,750,000 2017 2121 1697 1212 911⁄2 15 2 321⁄2 25514911⁄2 81 TPX 400 2000 NEA 400 2,000,000 2259 2424 1939 1385 991⁄2 15 2 321⁄2 25514911⁄2 89 TPX 600 1000 NEA 600 1,000,000 1450 1212 970 693 119 15 11⁄4 321⁄2 2 67 10 84 109 TPX 600 1250 NEA 600 1,250,000 1692 1515 1212 866 119 15 11⁄4 321⁄2 2 67 12 84 1091⁄3 HP - 8.6 Amps TPX 600 1500 NEA 600 1,500,000 1935 1816 1455 1039 119 15 11⁄2 321⁄2 2 67 12 84 109 TPX 600 1750 NEA 600 1,750,000 2177 2121 1697 1212 119 15 2 321⁄2 25514911⁄2 109 TPX 600 2000 NEA 600 2,000,000 2419 2424 1939 1385 119 15 2 321⁄2 25514911⁄2 109
Certified Minimum Installation Clearances to Combustibles:
Front: 18 inches Back: 0 inches Sides: 0 inches Top: 5 inches
A clearance of 24 inches should be maintained from serviceable parts such as relief valve, power burner, drain valve and anodes (anodes are located on side above cold water inlet).
Minimum gas supply pressure: 7 Inches W.C. Maximum gas supply pressure: 13 Inches W.C.
TPX models are Category I appliances (Fan Assisted) and require a negative draft. These units should only be commonly vented with other Category I negative draft appliances per the latest addition of the National Fuel Gas Code. An approved/listed Type “B” venting material is recommended. A negative draft of -0.02˝ to -0.07 is required in the vent.
Storage Capacity
Gallons Gas Rating 80°F Rise 100°F Rise 140°F Rise A B C D E F G H J
Input
Rating
BTU/Hr.
U.S. Natural Hour
First Recovery
Output (Gallons)
Dimensions In Inches
1
⁄2 14 11⁄4 261⁄2 11⁄2 60 12 72 83
ASME
1
⁄7 HP - 2.5 Amps
1
⁄3 HP - 8.6 Amps
1 HP - 12.4 Amps
1 HP - 12.4 Amps
Motor HP
120V 60 Hz 1
SCDSS00108 April 2008R
Page 3 of 6 ©2008 State Water Heaters Company
TITAN LV
TPO Power Oil Large Volume Commercial Water Heaters
SPECIFICATIONS
Actual
Model Number
Storage
Capacity
Gallons
U.S.
Input
Rating
BTU/Hr.
Firing
Rate GPH
TPO 150 140 OEA 163 140,000 1 170 136 97 831⁄214 –
TPO 150 199 OEA 163 199,000 1.4 241 193 138 831⁄2 14 –
TPO 150 255 OEA 163 255,000 1.8 309 247 176 831⁄2 14 –
TPO 150 270 OEA 163 270,000 1.9 327 262 187 831⁄2 14 –
TPO 150 400 OEA 151 400,000 2.8 485 387 277 831⁄2 14 –
TPO 150 540 OEA 151 540,000 3.8 654 524 374 831⁄2 14 –
TPO 150 720 OEA 145 720,000 5.1 873 698 416 831⁄2 14 –
Output (Gallons)
Recovery
80°F Rise 100°F Rise 140°F Rise A B C D E F G H J
Dimensions In Inches
273⁄4
11⁄4361⁄25 47 73 1292
273⁄4
11⁄4 361⁄2 6 47 73 1292
273⁄4
11⁄4 361⁄2 6 47 73 1292
273⁄4
11⁄4 361⁄2 6571⁄2 73 1397
273⁄4
11⁄4 361⁄2 7571⁄2 73 1397
273⁄4
11⁄4 361⁄2 8571⁄2 73 1505
273⁄4
11⁄4 361⁄2 10 571⁄2 73 15101⁄4 HP - 4.6 Amp TPO 200 300 OEA 221 300,000 2.1 364 291 208 831⁄2 15 – 321⁄2 11⁄2 443⁄4 6661⁄2 73 2098 TPO 200 600 OEA 221 600,000 4.2 727 582 416 831⁄215 – 321⁄211⁄2443⁄48661⁄273 2098 TPO 200 800 OEA 221 800,000 5.7 970 776 554 831⁄2 15 – 321⁄2 11⁄2 443⁄4 10 661⁄2 73 2103 TPO 200 1000 OEA 201 1,000,000 7.1 1212 970 693 831⁄2 15 – 321⁄2 11⁄2 443⁄4 10 661⁄2 73 21031⁄3 HP - 5.5 Amp TPO 200 1250 OEA 201 1,250,000 8.9 1515 1212 866 831⁄2 15 – 321⁄2 11⁄2 443⁄4 12 661⁄2 73 2467 TPO 200 1500 OEA 201 1,500,000 10.7 1818 1455 1039 831⁄2 15 – 321⁄2 11⁄2 443⁄4 12 811⁄2 73 27573⁄4 HP - 10.2 Amp TPO 300 300 OEA 300 300,000 2.1 364 291 208 911⁄2 14 – 261⁄2 11⁄2 443⁄4 6661⁄2 83 2150 TPO 300 600 OEA 300 600,000 4.2 727 582 416 911⁄2 14 – 261⁄2 11⁄2 443⁄4 8661⁄2 83 2150 TPO 300 800 OEA 300 800,000 5.7 970 776 554 911⁄214 – 261⁄211⁄2443⁄410 661⁄283 2308 TPO 300 1000 OEA 300 1,000,000 7.1 1212 970 693 911⁄2 14 – 261⁄2 11⁄2 443⁄4 10 661⁄2 83 23081⁄3 HP - 5.5 Amp TPO 300 1250 OEA 300 1,250,000 8.9 1515 1212 866 911⁄2 14 – 261⁄2 11⁄2 443⁄4 12 661⁄2 83 2584 TPO 300 1500 OEA 300 1,500,000 10.7 1818 1455 1039 911⁄2 14 – 261⁄2 11⁄2 443⁄4 12 811⁄2 83 27743⁄4 HP - 10.2 Amp TPO 400 600 OEA 411 600,000 4.2 727 582 416 911⁄2 15 – 321⁄2 2558761⁄2 81 32071⁄4 HP - 4.6 Amp TPO 400 800 OEA 411 800,000 5.7 970 776 554 911⁄215 – 321⁄225510761⁄281 3212 TPO 400 1000 OEA 411 1,000,000 7.1 1212 970 693 911⁄215 – 321⁄225510761⁄281 32121⁄3HP - 5.5 Amp TPO 400 1250 OEA 411 1,250,000 8.9 1515 1212 866 911⁄2 15 – 321⁄2 25512761⁄2 81 3212 TPO 400 1500 OEA 397 1,500,000 10.7 1816 1455 1039 911⁄2 15 – 321⁄2 25512911⁄2 81 3402 TPO 400 1750 OEA 397 1,750,000 12.5 2121 1697 1212 911⁄215 – 321⁄225514911⁄281 35283⁄4HP - 10.2 Amp TPO 400 2000 OEA 397 2,000,000 14.2 2424 1939 1385 991⁄215 – 321⁄225514911⁄289 3669 TPO 500 2250 OEA 495 2,250,000 16 2727 2182 1558 110 15 – 321⁄2 25516911⁄2 100 4277 TPO 500 2500 OEA 495 2,500,000 17.8 3030 2424 1732 110 15 – 321⁄2 25516911⁄2 100 4419 TPO 600 720 OEA 594 720,000 5.1 873 698 499 119 15 – 321⁄2 25510761⁄2 109 3667 TPO 600 1000 OEA 594 1,000,000 7.1 1212 970 693 119 15 – 321⁄225510761⁄2109 3667 TPO 600 1250 OEA 594 1,250,000 8.9 1515 1212 866 119 15 – 321⁄225512761⁄2109 36671⁄3HP - 5.5 Amp TPO 600 1500 OEA 594 1,500,000 10.7 1816 1455 1039 119 15 – 321⁄2 25512911⁄2 109 3837 TPO 600 1750 OEA 594 1,750,000 12.5 2121 1697 1212 119 15 – 321⁄2 25514911⁄2 109 38373⁄4 HP - 10.2 Amp TPO 600 2000 OEA 594 2,000,000 14.3 2424 1939 1385 119 15 – 321⁄2 25514911⁄2 109 3837 TPO 600 2250 OEA 575 2,250,000 16 2727 2182 1558 119 15 – 321⁄2 25516911⁄2 109 4477 TPO 600 2500 OEA 575 2,500,000 17.8 3030 2424 1732 119 15 – 321⁄225516911⁄2109 4619
Certified Minimum Installation Clearances to Combustibles:
Front: 18 inches Back: 0 inches Sides: 0 inches Top: 5 inches
A clearance of 24 inches should be maintained from serviceable parts such as relief valve, power burner, drain valve and anodes (anodes are located on side above cold water inlet).
State Titan TPO models are Category I appliances (Fan Assisted) and require a negative draft. These units should only be commonly vented with other Category I negative draft appliances per the latest addition of the National Fuel Gas Code. An approved/listed Type “B” venting material is recommended. A negative draft of -0.02˝ to -0.07 is required in the vent.
Ship.
Wt. Motor HP
w/Burner 120V 60 Hz 1
(lbs.)
1
⁄7 HP - 4.4 Amp
1
⁄4HP - 4.6 Amp
1 HP - 16 Amp
1
⁄4 HP - 4.6 Amp
1 HP - 16 Amp
ASME
SCDSS00108 April 2008R
Page 4 of 6 ©2008 State Water Heaters Company
TITAN LV
TPD Power Dual Fuel Large Volume Commercial Water Heaters
SPECIFICATIONS
Actual
Model Number
Storage
Capacity
Gallons
U.S.
151
151
Input
Rating
BTU/Hr.
350,000
Firing
Rate GPH
2.2 348 TPD 150 400 ONEA 151 400,000 2.8 485 387 277 83 TPD 150 540 ONEA 151 540,000 3.8 654 524 374 831⁄2 14 1 273⁄4 11⁄4 361⁄2 8571⁄2 73 1505 TPD 150 720 ONEA 145 720,000 5.1 873 698 416 831⁄2 14 11⁄4 273⁄4 11⁄4 361⁄2
2.2
Output (Gallons)
Recovery
80°F Rise 100°F Rise 140°F Rise A B C D E F G H J
348
339
339
242
242
1
⁄2 14 1 273⁄4 11⁄4 361⁄2
1
⁄2 14 1 273⁄4 11⁄4 361⁄2 7571⁄2 73 1397
1
⁄2 15 1 321⁄2 11⁄2 443⁄4
Dimensions In Inches
1
7
⁄2 73 1397
1
⁄2 73 15101⁄4 HP - 4.6 Amp
1
⁄2 73 2098
7
Ship.
Wt. Motor HP
w/Burner 120V 60 Hz 1
(lbs.)
1
⁄4 HP - 4.6 Amp
TPD 200 600 ONEA 221 600,000 4.2 727 582 416 831⁄215 1 321⁄211⁄2443⁄48661⁄273 2098 TPD 200 800 ONEA 221 800,000 5.7 970 776 554 831⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 10 661⁄2 73 2103 TPD 200 1000 ONEA 201 1,000,000 7.1 1212 970 693 831⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 10 661⁄2 73 21031⁄3 HP - 5.5 Amp TPD 200 1250 ONEA 201 1,250,000 8.9 1515 1212 866 83 TPD 200 1500 ONEA 201 1,500,000 10.7 1818 1455 1039 831⁄2 15 11⁄2 321⁄2 11⁄2 443⁄4 12 811⁄2 73 27573⁄4 HP - 10.2 Amp
2.2
348
339
242
TPD 300 600 ONEA 300 600,000 4.2 727 582 416 911⁄2 14 1 261⁄2 11⁄2 443⁄4 8661⁄2 83 2150
1
⁄2 15 11⁄4 321⁄2 11⁄2 443⁄4 12 661⁄2 73 2467
1
⁄2 14 1 261⁄2 11⁄2 443⁄4
7
1
⁄2 83 2150
1
⁄4HP - 4.6 Amp
TPD 300 800 ONEA 300 800,000 5.7 970 776 554 911⁄214 11⁄4261⁄211⁄2443⁄410 661⁄283 2308 TPD 300 1000 ONEA 300 1,000,000 7.1 1212 970 693 911⁄2 14 11⁄4 261⁄2 11⁄2 443⁄4 10 661⁄2 83 23081⁄3 HP - 5.5 Amp TPD 300 1250 ONEA 300 1,250,000 8.9 1515 1212 866 911⁄2 14 11⁄4 261⁄2 11⁄2 443⁄4 12 661⁄2 83 2584 TPD 300 1500 ONEA 300 1,500,000 10.7 1818 1455 1039 911⁄2 14 11⁄2 261⁄2 11⁄2 443⁄4 12 811⁄2 83 27743⁄4 HP - 10.2 Amp TPD 400 600 ONEA 411 600,000 4.2 727 582 416 911⁄2 15 1 321⁄2 2558761⁄2 81 32071⁄4 HP - 4.6 Amp TPD 400 800 ONEA 411 800,000 5.7 970 776 554 911⁄215 11⁄4321⁄225510761⁄281 3212 TPD 400 1000 ONEA 411 1,000,000 7.1 1212 970 693 911⁄215 11⁄4321⁄225510761⁄281 32121⁄3HP - 5.5 Amp TPD 400 1250 ONEA 411 1,250,000 8.9 1515 1212 866 91
1
⁄2 15 11⁄4 321⁄2 25512761⁄2 81 3212 TPD 400 1500 ONEA 397 1,500,000 10.7 1816 1455 1039 911⁄2 15 11⁄2 321⁄2 25512911⁄2 81 3402 TPD 400 1750 ONEA 397 1,750,000 12.5 2121 1697 1212 911⁄215 2 321⁄225514911⁄281 35283⁄4HP - 10.2 Amp TPD 400 2000 ONEA 397 2,000,000 14.2 2424 1939 1385 991⁄215 2 321⁄225514911⁄289 3669 TPD 500 2250 ONEA 495 2,250,000 16 2727 2182 1558 110 15 2 321⁄2 25516911⁄2 100 4277 TPD 500 2500 ONEA 495 2,500,000 17.8 3030 2424 1732 110 15 2 321⁄2 25516911⁄2 100 4419 TPD 600 720 ONEA 594 720,000 5.1 873 698 499 119 15 11⁄4 321⁄2 25510761⁄2 109 3667 TPD 600 1000 ONEA 594 1,000,000 7.1 1212 970 693 119 15 11⁄4321⁄225510761⁄2109 3667
1 HP - 16 Amp
1
⁄4 HP - 4.6 Amp
TPD 600 1250 ONEA 594 1,250,000 8.9 1515 1212 866 119 15 11⁄4321⁄225512761⁄2109 36671⁄3HP - 5.5 Amp TPD 600 1500 ONEA 594 1,500,000 10.7 1816 1455 1039 119 15 11⁄2 321⁄2 25512911⁄2 109 3837 TPD 600 1750 ONEA 594 1,750,000 12.5 2121 1697 1212 119 15 2 321⁄2 25514911⁄2 109 38373⁄4 HP - 10.2 Amp TPD 600 2000 ONEA 594 2,000,000 14.3 2424 1939 1385 119 15 2 321⁄2 25514911⁄2 109 3837 TPD 600 2250 ONEA 575 2,250,000 16 2727 2182 1558 119 15 2 321⁄2 25516911⁄2 109 4477 TPD 600 2500 ONEA 575 2,500,000 17.8 3030 2424 1732 119 15 2 321⁄225516911⁄2109 4619
Certified Minimum Installation Clearances to Combustibles:
Front: 18 inches Back: 0 inches Sides: 0 inches Top: 5 inches
A clearance of 24 inches should be maintained from serviceable parts such as relief valve, power burner, drain valve and anodes (anodes are located on side above cold water inlet).
State Titan TPD models are Category I appliances (Fan Assisted) and require a negative draft. These units should only be commonly vented with other Category I negative draft appliances per the latest addition of the National Fuel Gas Code. An approved/listed Type “B” venting material is recommended. A negative draft of -0.02˝ to -0.07 is required in the vent.
1 HP - 16 Amp
ASME
SCDSS00108 April 2008R
Page 5 of 6 ©2008 State Water Heaters Company
COMMERCIAL
TITAN LV
Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters
SUGGESTED SPECIFICATIONS
TITANTM LV POWER GAS (MODELS TPG)
Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design and include a powered gas burner with electronic flame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure regulator, diaphragm air switch for proof of blower operation, and flame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, and stamped National Board, and listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door shall be hinged for easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation. Heater(s) must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efficiency and standby loss. The outer jacket shall have a baked powder coat finish. All internal surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel by firing at a temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty. Professional start-up service to be included.
TM
TITAN
Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design and include a powered gas burner with electronic flame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure regulator, diaphragm air switch for proof of blower operation, and flame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, ASME stamped and listed
by Underwriters Laboratories. The water heater shall be approved for low NOx and meet or exceed California rule 1146.2. Controls shall include:high temperature limit control (manual reset), up per and lower thermostats, modulating control, combination temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door shall be hinged for easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation. Heater(s) must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efficiency and standby loss. The outer jacket shall have a baked powder coat finish. All internal surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel by firing at a temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty. Professional start-up service to be included.
LV POWER LOW NO (MODELS TPX)
X
SUGGESTED SPECIFICATIONS
TITANTM LV POWER OIL AND DUAL FUEL (MODELS TPO AND TPD)
Water heater(s) shall be Model_____________________as manufactured by the State Water Heaters or an approved equal. Heater(s) shall have a minimum oil firing rate of_____gallons per hour, an input rating of____________BTU/HR. The heater(s) shall have a recovery rate of_____GPH at a 100°F rise and a storage capacity of______gallons. The 160 psi design pressure tank shall be glass-lined with an alkaline borosilicate composition and fused to the steel by firing at 1600°F.The heater(s) shall be equipped with______NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, and carry a National Board stamping. The heater(s) shall be ASME and the entire unit listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination temperature and pressure gauge, low water cutoff, ASME rated temperature and pressure relief valve, and barometric draft regulator. Control compartment door shall be hinged for easy access and include cam locks for security. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation and meet or exceed current standard of ASHRAE 90.1-1999 for standby loss and recovery efficiency. The heater(s) shall include a drain valve and flame observation port. The jacket shall be baked powder coat finish. Heater(s) vessel shall have a 3, 5 or 10 year limited warranty against failure as outlined in the written warranty.
The TPO models shall have a UL listed burner with two-stage pump, oil safety valve, electronic flame safeguard, intermittent ignition and diaphragm air switch for proof of flame operation.
The TPD models shall include a dual fuel burner with two-stage oil pump, oil safety valve, electronic flame safeguard, intermittent ignition, diaphragm air switch, main and pilot automatic gas valves, gas pressure regulator and manual crossover switch.
In keeping with our policy of continuous product improvement, specifications are subject to change without prior notice.
SUGGESTED SPECIFICATIONS
For more information on State® contact: State Water Heaters 500 Tennessee Waltz Parkway, Ashland City, TN 37015
800.365.0024 Toll-free USA www.statewaterheaters.com
SCDSS00108 April 2008R Page 6 of 6 ©2008 State Water Heaters
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use