Page 1
YCR-M08-10
User Guide
Robot Vacuum Cleaner iClebo STAR WARS
■Make sure to read "safety precautions" before use and then use strictly in accordance with instructions.
■Included in this User Guide is the device Warranty.
Customer Service Center Tel: 1566-3292
Model name
Input power
Standby power
Main body power
consumption
Battery
Diameter
Height
Weight
Speed
Filter
Sensor
Charging time
After-sales Service & Customer
Service Inquiries
Usage time
Noise level
iClebo Star Wars (YCR-M08-10)
100~240 V
Less than 1 W
12 W
Lithium lon Battery
35 cm
8.9 cm
2.8 kg
300 mm/s (Max)
HEPA filter
Camera, PSD, IR, Gyro, encoder, bumper
About 110 minutes
(when used on the standard floor )
About 100 minutes
58 dB[A]
iAMN_EN.SW.V1
Head office #1214 Namseong Plaza, 130 Digital-ro, Geumcheon-gu, Seoul, South Korea
Factory #401-1001 Bucheon Techno Park, 655 Pyeongcheon-ro, Wonmi-gu, Bucheon, Gyeonggi-do, South Korea
www.iclebo.com www.yujinrobot.com
www.iclebo.com
Inquiries received by mobile
24 hours a day
m.iclebo.com
Mon~Fri
AM09:00~12:50 / PM01:50~06:00
Consult by telephone
1566-3292
Page 2
1
●
Table of Contents
Safety precautions
Components and their details
Notes
Installation of the Robot Cleaner
Use of the Robot Cleaner
Maintenance
Storage
Purchase of accessories
User self-check list
before requesting after-sales service
Display of inspection messages
Tips for effective cleaning
Operating principles of the Robot Cleaner
Before use
• Installation of the side brushes
• Installation of the charging station
• Mounting of the wet ultrafine fibrous mop
• Charging
Use of the Robot Cleaner
• Turning on / off power initially
• Starting and stopping cleaning
• Selection of operational modes
• Cleaning mode
• Movement / mannual cleaning / charging
• Scheduled cleaning
• Emptying the dust box
/ maintaining the HEPA filter
• Maintaining the side brushes
• Maintaining the sensor
• Maintaining the main brush
• Maintaining the front wheel
Purchase of accessories
Consumable replacement cycles to maintain
an optimal cleaning performance level
Before use
After Use
2
6
7
9
10
Use of the application (app)
• Installation
• Use
11
Application of the entry prevention tape
12
12
15
17
17
18
19
Page 3
Before use
●
Safety precautions
2
These precautions are intended to keep the user safe and to prevent
damage to properties.
Read carefully all contents below, and make sure to use safely.
Ignorance or violation of these safety precautions
/ instructions could cause a significant injury or
death in the worst case.
Ignorance or violation of these safety precautions
/ instructions could cause a minor injury or
damage to the Robot Cleaner.
Warning
Caution
Warnings
Do NOT let an
inflammable substance,
surfactant or liquid drink
sprayed or sucked over or
around the Robot Cleaner.
- Otherwise, fire or
malfunction could be
caused.
In case the Robot Cleaner
gets soaked in water,
make sure to consult the
Service Center
(Tel: 1566-3292)
even after it gets
completely dried.
- Otherwise, a disorderly
operation or malfuction
could be caused.
Do NOT touch the power
plug with wet hands.
- Otherwise, an electric
shock could be caused.
Do NOT disassemble or
modify the Robot Cleaner
unless you are a qualified
repairer.
- Otherwise, fire or an
electric shock could be
caused.
Do NOT place the charing
station and Robot Cleaner
near any heat source.
- Otherwise, the
appearance could be
deformed or fire or malfunction could be caused by
collision.
Do NOT forcibly use the
power plug if damaged,
bent or loose.
- Otherwise, fire or an
electric shock could be
caused.
Wipe moisture, if any, off
the power plug and keep it
clean.
- Otherwise, a disorderly
operation or electric shock
could be caused.
Make sure to keep a table
or cables away in order to
avoid entanglement.
- Otherwise, fire or an
electric shock could be
caused.
Page 4
3
●
Safety precautions
Make sure to keep any
inflammable, fragile or
fibrous substance away
before using the Robot
Cleaner.
- Otherwise, fire or a
disorderly operation could
be caused.
Make sure to use the power
plug solely in a socket with
a capacity larger than 5A.
- Otherwise, fire could be
caused by a heated
multi-plugged socket.
Refrain from using the
Robot Cleaner with a child
or pet alone around.
- A child or pet could be
curious about the Robot
Cleaner.
Take extra care of the
Robot Cleaner when used
in a room where a human
being or pet sleeps.
- Otherwise, injury or
damage to the device could
be caused.
Do NOT insert any human
body part like a finger or
toe under the rotating brush
or wheel.
- Otherwise, injury or
damage to the device could
be caused
Do NOT let a child play with
the Robot Cleaner.
- Otherwise, injury or
damage to the device could
be caused.
A human body part can get
injured if trapped into a
rotating part like the wheel.
- If you follow and distract
the movement of the Robot
Cleaner, it could be recognized as an obstacle, thus
leaving the area uncleaned.
Do NOT let a child sit on
the Robot Cleaner when
used. Do NOT let another
object tied to the Robot
Cleaner when used.
- Otherwise, fire or an
electric shock could be
caused.
Make sure to hold tight the
power plug body when
pulling it off and NOT to
allow any finger to touch
plug pins.
- Otherwise, fire or an
electric shock could be
caused.
Make sure to connect the
adapter to the charging
socket in case of
charging directly with the
adaptor.
- Otherwise, fire or an
electric shock could be
caused.
Do NOT push in and pull
out the power plug repetitively.
- Otherwise, fire or an
electric shock could be
caused.
Do NOT use the battery
and the charging station for
anything other than the
Robot Cleaner.
- Fire or malfunction could
be caused.
Page 5
5cm
5cm
Entry prevention tape
4
In case you experience an unidentifiable or unfamiliar noise, smell or
smoke, stop using the Robot Cleaner immediately and then call the
Customer service Center (Tel: 1566-3292).
- Fire or an electric shock could be caused.
-10°c
Cautions
5cm
10
●
Safety precautions
Take Precautions as
required when cleaning an
area or staircase with the
height of less than 5 cm,
thus having the risk of an
inadvertent fall.
- Make sure to apply the
entry prevention tape as
indicated before use.
Do NOT use the Robot
Cleaner on the floor with a
slope of over 10 degrees.
- Otherwise, the device
might not perform as
effectively as it should.
Manually re-locate the
Robot Cleaner in case it
gets stuck or trapped at the
threshold of a door or
veranda, etc.
Stop using the Robot
Cleaner if the brush is
found to have damaged
your carpet.
- Either long or thin carpet
threads could be damaged.
A scratches or damage
could be caused depending
on the
property or quality of a
specific wood floor.
- Refrain from using the
Robot Cleaner.
In case the Robot Cleaner
was left
unattended at a low
temperature (below -10 °C)
for a long time, let it stay at
a room
temperature / charged
for over 2 hours first and
then use.
- Otherwise, malfunction
could be caused.
Do NOT leave the Robot
Cleaner with power on
unattended on the desk or
chair.
- Otherwise, injury or
damage to the device could
be caused.
Do NOT let strong
external shock applied to
the Robot Cleaner. Do NOT
drop it either.
- Otherwise, injury or
damage to the device could
be caused.
Refrain from using the
Robot Cleaner in a
no-entry area.
- When unavoidable, make
sure to apply the entry
prevention tape first and
then use.
Refrain from using the
Robot Cleaner in an area
with the height of more than
5 cm, thus having the risk
of an inadvertent fall (e.g.
veranda, front door,
restroom, etc).
- Make sure to apply the
entry prevention tape as
indicated before use.
Page 6
5
●
Safety precautions
Do NOT let any metallic
object in contact with the
main body or charging port.
- Otherwise, a disorderly
operation or malfunction
could be caused.
Mop or clean fluid, oil or
animal excretion away from
the floor before use.
- Otherwise, a disorderly
operation or malfunction
could be caused.
Empty the dust box before
using the Robot Cleaner.
- If the dust box is full,
suction power could be lost.
Remove any large trash or
vinyl bag immediately if
sucked by the Robot
Cleaner.
- Use of the Robot Cleaner
with the inlet blocked for a
long time could lead to fatal
damage to the device.
Before use, make sure that
all key components - filter,
brush, dust box, etc. - are
correctly assembled .
- Otherwise, cleaning might
not be completed properly
or malfunction could be
caused.
The Robot Cleaner could
collide, when in
operation, with long and thin
furniture items like chair
legs.
- Make sure to put such
potential obstacles aside…
e.g on the table so that
cleaning can be processed
fast and effectively.
Do NOT press the bumper
hard or apply strength
forcibly to it.
- Otherwise, a disorderly
operation could be caused.
Do NOT use in an outdoor
environment.
- Otherwise, malfunction
could be caused.
Do NOT let chopsticks or
pins inserted into the sensor
holes of the Robot Cleaner.
- Otherwise, a disorderly
operation or malfunction
could be caused.
Do NOT let liquid, blades,
thumbtacks or ember
sucked into the Robot
Cleaner.
- Otherwise, a disorderly
operation, malfunction or
fire could be caused.
Page 7
After use
●
Safety precautions
6
Warnings
When you maintain the Robot Cleaner, do NOT spray water directly on
its surface or clean it with any inflammable liquid such as benzene,
thinner or alcohol.
Cautions
Unwanted or foreign
substances placed on the
sensor area could cause a
disorderly operation.
- Make sure to clean the
sensor area periodically.
Make sure to pull out the
power plug first for your
safety when you need to
conduct a maintenance
work on the the charging
station.
Do NOT throw away any
used battery into a live
flame in order to avoid the
risk of explosion.
Contact the manufacturer or
Customer Service Center
(Tel: 1566-3292) for help in
case the Robot Cleaner or
its component gets damaged.
- Otherwise, fire or an
electric shock could be
caused.
Make sure to turn off the
power switch located on the
side of the device when you
use the
cleaning brush to remove
foreign substances from the
main brush and side
brushes.
- Otherwise, the Robot
Cleaner could suddenly
start operation and cause
injury or fatal damage to the
device.
Page 8
YCR-M08-10
www.iclebo.com
7
●
Components and their details
Components
Component Details
Robot Cleaner Charging station
Side brush (R)
Side brush (L)
HEPA filter (2 ea)
Cleaning brush
(※ Located inside the
charging station.) Entry prevention tape
Mop platewet ultrafine
fibrous mop (2 ea)
● Upper part of the Robot Cleaner
● Lower part of the Robot Cleaner
Main
brush
fixing clip
Front wheel
station
Lithium-ion
battery
Charging
port
Wheel
Side brush
fixing pin
Side brush
Mannual
charging jack
Power switch
Power button
Camera
Mode button
Start / stop button
Dust box
Bumper
Obstacle
sensor
Front wheel
Front
wheel
fixing cover
Main brush
Main
brush
cover
Mop plate
User guide
※Separately purchasable
Remote Controller
MODE
CLOCK TIMER
MAX
www.iclebo.com/shop
Adapter
Make sure that the adapter plug is
assembled properly to avoid the risk
of fire.
User Guide
Robot Vacuum Cleaner iClebo STAR WARS
■Make sure to read "safety precautions" before use and then use strictly in accordance with instructions.
■Included in this User Guide is the device Warranty.
Customer Service Center Tel: 1566-3292
Page 9
8
●
Components and their Details
● Charging station
● Display window
● Dust Box
Dust box
Blades
Dust filter
Anti-microbial filter
/ Electrostatic filter
Filter case
Start / stop button
Time
/ cleaning
duration
Threshold
mode
Scheduling
status
Nav
mode
Random
mode
Wet mop
mode
Battery
level
Power
Mode selection
Anti-slip
pads
Infrared generator
Charging status
indicator
Charging ports
Notes
Respect the following instructions to enhance cleaning efficiency:
-Empty the dust box after using the Robot Cleaner.
-An area intended not to be cleaned should be clearly marked or bordered by applying the entry
prevention tape or by having the door(s) closed.
-Keep aside any movable obstacles like toys, magazines or shoes before using the Robot
Cleaner.
-Do NOT manually lift or re-locate the Robot Cleaner when in operation.
(Otherwise, a memorized cleaning course or uncleaned area could be caused.)
Tips for effective cleaning
Page 10
9
●
Notes
Operating principles of the Robot Cleaner
Operating principles of the Robot Cleaner
The device uses a camera and various sensors to detect and recognize the ceiling and obstacles,
information on which is then used to create a virtual map located inside the CPU installed at the
main body as it cleans. It decides on either cleaned areas or to-be-cleaned areas by itself as it
generates the most effective map when in operation(except under the random mode or max mode
of operation). 15 built-in detection sensors allow the Robot Cleaner to minimize butts to the wall
or other objects such as chairs and flowerpots. The Robot Cleaner can be operational on the floor
with a threshold of as high as 18 mm, and it detects the staircase using the floor sensor to prevent
itself from falling down.
Suction of the Robot Cleaner
The Robot Cleaner is equipped with one main brush, two side brushes and one vacuum
suction inlet. Dust on the floor is collected by the rotating side brushes and then swept
by the rotating main brush into the dust box.
●
Installation of the Robot Cleaner
Before use
1. Turn upside down the Robot Cleaner, and check the
locations of the left and right side brushes.
2.
3.
※ A soft fabric patch laid on the floor would help reduce
scratches on the upper plate of the Robot Cleaner.
Installation of the side brushes
1 2
※ Caution :
Make the hole and pole of the side brush fit each
other correctly and then push into the position.
※ Adapter Connection
illustrated
Installation
of the
charging
station
4
1
2
1. Open the rear cover of the charging station and then
mount the adapter with a power plug connected, as
illustrated here.
2.
Completely connect the charging jack of the adaptor to
the jack inside the charging station.
3. Place the cable in an orderly way inside the rear space
of the charging station.
4. Secure space as wide as 0.5 m on both sides and deep
at least 1.5 m from the front of the charging station.
3
Place the L-side brush over the axis of a pole near the
L mark and then push forcibly into the position.
Place the R-side brush over the axis of a pole near the
R mark and then push forcibly into the position.
Page 11
10
●
Installation of the Robot Cleaner
Mounting of the wet ultrafine fibrous mop
Charging
1
2
Mop plate
1. Turn the Robot Cleaner upside down
and then fit the mop plate into the
mounting area of the main body.
2.
※ The threshold mode will not be set
up when the mop plate is mounted
on the device.
Soak the wet ultrafine fibrous mop
into water, squeeze a good amount of
water out of the mop and then mount
it onto the mop plate.
Wet ultrafine
fibrous mop
1. Turn on the power switch at the side of the Robot Cleaner.
2. Align the charging pin located under the main body into the charging station port and then start
charging.
▶▶ The battery level blinks on the display window, indicating that charging has started.
"Lo" in the time display section indicates that no charged battery is left.
3. A green light blinks while charging is in progress. Once fully charged, the battery level remains
green on the display window. A red light turns off at the charging station once the docking stage
has reached.
[Automatic charging when in use]
※ The Robot Cleaner moves to the charging station by itself when the battery level becomes low while
it is operating. Once charging has been completed, it returns to the area left uncleaned, completes
the cleaning job and then returns finally to the charging station.
※ Press the ‘Charge' button on the app in case you want to charge while the Robot Cleaner is operating.
(Refer to Charging on p.14.)
※ The Robot Cleaner is set to return to the area where the cleaning job originally started when the
battery level becomes low. Therefore if the cleaning job started in an area other than the charging
station, it returns to the area where the cleaning job originally started.
※ The Robot Cleaner stays in an operation mode when while the power switch is turned on, but in a
charging only mode when the power switch is turned off.
※ In case you wish to charge the Robot Cleaner manually,
connect the charging jack of the adaptor directly with the
main body.
[Manual charging]
1 2 3
Main body
Red Green
Green
Charging station
power
Charging display Charging in progress Changing completed
Loading...