StarTech.com WIFI2HDMC, WIFI2HDMCGE User Manual
Wireless Display Adapter for Mobile Devices
WIFI2HDMC / WIFI2HDMCGE
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 12/11/2013
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
Table of Contents
Product Diagram ....................................................................................1
Rear View ...................................................................................................................................................... 1
Side View ...................................................................................................................................................... 1
Introduction ............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements .............................................................................................................................. 2
Preparing Your Site ................................................................................2
Initial Setup .............................................................................................4
Playing Media from a USB Stick ...........................................................6
AirFun Utility ...........................................................................................7
Installation ................................................................................................................................................... 7
Operation ..................................................................................................................................................... 8
ScreenShare Mode ................................................................................11
Installation ................................................................................................................................................... 11
Operation ..................................................................................................................................................... 13
Wi Direct – Miracast mode ..................................................................17
Android Wireless Display (Android 4.2 or higher) ......................................................................... 18
AllShareCast (Samsung) .......................................................................................................................... 19
Intel WiDi Application .............................................................................................................................. 20
Windows 8.1 Wireless Display ............................................................................................................... 21
Advanced Setup Menu ..........................................................................22
Instruction Manual
i
Specications ..........................................................................................28
Technical Support ..................................................................................29
Warranty Information ............................................................................29
Instruction Manual
ii
Product Diagram
Rear View
Analog Audio/Video out
(For included 4 position
A/V cable only)
Side View
Instruction Manual
HDMI Out
RJ45 LAN
USB Media
Input
1
Power
On/O
Mode Select
Button
DC
Jack
Introduction
Packaging Contents
• 1x Wireless Display Adapter
• 1x Universal Power Adapter (NA/UK/EU)
• 1x USB Cable to Power Adapter Port (optional for USB Power source)
• 1x 4 position A/V cable
• 1x Software Installation Disc
• 1x Quick Installation Guide
System Requirements
• HDMI enabled display device (i.e. television, projector)
• 802.11n/g Wireless enabled video source device (i.e. Smartphone, computer)
• HDMI cable
• Available AC electrical outlet or USB power source
Preparing Your Site
1. Determine where the display will be located and place/ mount the
display appropriately.
NOTE: The maximum distance of the display adapter is limited to the distance of your
802.11n/g Wireless network device. If the wireless signal is obstructed by walls, or other
interference the signal quality and maximum distance will likely be reduced.
Ensure the Receiver Unit is situated near an available AC electrical outlet.
Instruction Manual
2
Hardware Installation
1. Connect an HDMI video cable from the HDMI out port on the Wireless Video
Adapter to the HDMI in port on the HDMI enabled display device.
2. Connect the power adapter from an available AC outlet to the power adapter port
on the Wireless Video Adapter.
or
Connect the USB to power cable from an available USB power source to the power
adapter port on the Wireless Video Adapter.
3. Press the Power button to the in position to turn on the device, the Power LED will
be activated.
4. (Optional) If you intend to use the device for Screen sharing over a wired LAN
Network, connect an Ethernet cable from the RJ45 LAN port on the Rear of the
WIFI2HDMC, to an available LAN port on your local network gateway device
(router/hub).
5. (Optional) If you intend to output to an analog audio or video source, connect
the included “4 Position A/V cable” from the Analog Audio/Video out port to
Component video/RCA Audio input source on your analog audio or video device.
Note: Analog output will only work with the included 4 Position A/V cable. Analog
Audio/Video is not supported in Miracast mode.
Instruction Manual
3
Initial Setup
Once the WIFI2HDMC device is connected to your TV and powered on, the following
screen will show on the display.
1. Connect your Smartphone / Tablet or Notebook to the SSID of the device. By default
the SSID for the device is “WIFI2HDMC xxx” with no security key.
2. Once you have connected to the device, open your web browser and enter the
Setup IP address listed on the display which will bring up the remote control
interface. The default is http://192.168.59.254/remote
3. Select OK on the remote interface.
Instruction Manual
4
4. From the Initial Setup menu, modify the following options to suit your application.
Language: Select your desired language for the interface.
TV System: Congure WIFI2HDMC to use a specic resolution if needed. Note: It is
recommended to leave this option as HDMI Auto
WiFi Connection (optional): You may want to connect the device to your WiFi
network for one of the following reasons.
a. Create a network bridge. When your mobile device is connected to the WIFI2HDMC
SSID directly, this option enables you to still browse the internet or access your LAN,
through the WIFI2HDMC device.
b. Enable the WIFI2HDMC to access DLNA servers on your network.
c. Access the WIFI2HDMC remote interface from your LAN instead of a direct
connection to WIFI2HDMC SSID.
Virtual AP Bridge: Select one of the following options.
a. Bridge to Wireless – This will bridge the WIFI2HDMC network with your wireless LAN
so that you can access the internet or LAN devices through the WIFI2HDMC.
b. Bridge to Ethernet– This will bridge the WIFI2HDMC network with your wired LAN so
that you can access the internet or LAN devices through the WIFI2HDMC.
c. Virtual AP only – Devices connected to the WIFI2HDMC network can only access the
WIFI2HDMC device.
Save Change: Saves all changes.
Instruction Manual
5
5. Once complete, you should see the following screen to indicate the device is ready
to stream media.
Playing Media from a USB Stick
1. Connect your Smartphone / Tablet or Notebook to the WIFI2HDMC device and
navigate to the Setup (remote) page using a web browser.
2. Plug your USB stick into the port located on the side of the WIFI2HDMC device.
3. Navigate the USB stick contents using the web remote to choose the video, music or
picture le you would like to view.
Instruction Manual
6
AirFun Utility
Installation
The AirFun utility is available for PC (on the included software CD), iPhone or Android
platforms.
Android / iPhone
1. Download and install the latest version of the AirFun utility from your mobile app
store
PC
1. Insert the included software CD into the computer’s CD/DVD drive, or download the
latest drivers from http://www.starTech.com.
2. Run the Autorun.exe application from the Autoplay menu. If Autoplay is disabled
on your system, browse to your CD/DVD drive and run the application.
3. Select Software Installation from the menu.
4. Choose Typical Installation from the following screen and click Install.
Note: This will install both the AirFun and the ScreenShare utilities (outlined later in
this manual). Should you only desire to install only the AirFun utility, choose Custom
Installation and de-select Screenshare.
Instruction Manual
7
Loading...