VGA PC to TV Video Converter with
Remote Control
VGA2NTSCPRO
VGANTSCPROGB
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 07/20/2012
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
Table of Contents
Introduction ............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements .............................................................................................................................. 1
Installation ..............................................................................................2
Troubleshooting ........................................................................................................................................ 6
Specications ..........................................................................................7
Technical Support ..................................................................................8
Warranty Information ............................................................................8
Instruction Manual
i
Introduction
Thank you for purchasing a StarTech.com VGA to NTSC/PAL television converter. This
converter accepts your computer’s VGA signal and converts the graphic data into
video format (composite, S-Video and analog RGB for SCART implementation). With
great video quality and Zoom, Freeze, and numerous other adjustable functions, the
VGA2NTSCPRO is the ideal tool for synchronizing your monitor and television screens.
Packaging Contents
• 1 x VGA to NTSC/PAL TV converter
• 1 x remote control (with battery)
• 1 x 15-pin high-density VGA extension cable
• 1 x composite video cable
• 1 x S-Video cable
• 1 x 9V power adapter
System Requirements
• An IBM-PC (or compatible) computer
• TV set or video input device with Composite Video, S-Video, or SCART connector
• SCART users are required to provide an appropriate SCART video cable
Instruction Manual
1
Installation
1. Make sure that the converter, computer, monitor, and television are all turned o.
2. Unplug your monitor from your computer. Plug your monitor’s cable into the
converter’s Monitor port.
3. Connect the 15-pin high density extension cable to your computer’s VGA card/
monitor port and the converter’s VGA In port.
4. Depending on your television, use the appropriate cable to connect either the S-Out
(S-Video) port, the C-Out (composite video) port, or the RGB Out (SCART) port to
your television.
5. Make sure that the NTSC/PAL button is set appropriately: IN for NTSC systems, OUT
for PAL video systems.
6. Make sure that the Video/RGB button is set appropriately: IN for Composite or SVideo
systems, OUT for SCART systems.
7. Plug the DC 9V power adapter into the DC9V port and an available power source.
8. Turn on your computer, monitor, and television.
9. Make sure that your television is on the proper “Video Input” channel. Consult the
television manufacturer’s documentation if necessary. Turn on the converter. You
should now see an identical image on your monitor and television screen
Using the On-Screen Display
The On-Screen Display (OSD) allows you to easily navigate and select the dierent
settings and modes available on your converter. The OSD appears as a blue and white
menu bar across the top of your screen. To bring up and use the OSD menus, you can
use the four push-buttons on the top of the converter. The buttons are (from right):
Menu: Pressing this button will open/close the OSD main menu. The OSD menu
will also automatically close after several seconds of non-activity. Select: Pressing
this button will select an OSD menu option or setting. +/-: These two buttons scroll
through the available menu options or settings.
NOTE: You can also use the remote to access the OSD. See “Using the Remote” on page
7 for more details. There are eight functions available on the OSD menu:
To select the function you would like to adjust, use the +/- buttons to scroll between
the menu options. (The active option is marked with a yellow-orange highlight). Press
the Select button to view a function’s settings.
Instruction Manual
2
Sharpness
There are eight sharpness levels available to choose from. To adjust the sharpness:
1. Press the Menu button to call up the OSD menu.
2. Use the +/- buttons to scroll to the Sharpness icon. Press the Select button to view
the sharpness settings.
3. Use the +/- buttons to scroll through the sharpness settings until you reach your
ideal sharpness level.
4. Push the Select button to save the sharpness level and press the Menu button to
exit the sharpness function. You can also allow the converter to sit idle for a few
seconds. This will save the sharpness setting and exit the OSD automatically.
Zoom
The VGA2NTSCPRO performs a 2X zoom in both horizontal and vertical directions.
Using the zoom mode also involves selecting which quadrant of the screen you want
to zoom in on.
1. Press the Menu button to call up the OSD menu.
2. Use the +/- buttons to scroll to the Zoom icon. Press the Select button to view the
zoom settings mode.
3. Press Select to enter Zoom mode.
4. Use the +/- buttons to scroll between the four dierent quadrants of the screen. You
can also press the Select button again to exit Zoom mode and return to normal mode.
5. Once you are happy with your zoom settings, allow the converter to sit idle for a few
seconds. This will save the zoom settings and exit the OSD automatically.
Panning
The VGA2NTSCPRO allows you to pan across your image both vertically and horizontally.
1. Press the Menu button to call up the OSD menu.
2. Use the +/- buttons to scroll to the Panning icon. Press the Select button to view the
panning settings.
3. A pair of small arrows will indicate whether you are in Vertical or Horizontal pan
mode. Use the Select button to toggle between Vertical and Horizontal mode.
4. Depending on your mode, the + button will pan either up or right. The - button will
pan either down or left.
5. Once you are happy with your panning settings, allow the converter to sit idle for a
few seconds. This will save the panning settings and exit the OSD automatically.
Instruction Manual
3
Horizontal/Vertical Scaling
The VGA2NTSCPRO allows horizontal and vertical scaling so that an image can be
scaled to meet the visible part of your TV screen. If you are in Zoom mode, vertical
scaling is disabled.
1. Press the Menu button to call up the OSD menu.
2. Use the +/- buttons to scroll to the H/V Scaling icon. Press the Select button to view
the scaling settings.
3. A pair of small arrows will indicate whether you are in Vertical or Horizontal scale
mode. Use the Select button to toggle between Vertical and Horizontal mode.
4. The + button will spread your screen out towards the edges. The - button will
“tighten” or shrink the screen.
5. Once you are happy with your scaling settings, allow the converter to sit idle for a
few seconds. This will save the scaling settings and exit the OSD automatically.
Positioning
The positioning function allows you to move your TV image both vertically and horizontally.
1. Press the Menu button to call up the OSD menu.
2. Use the +/- buttons to scroll to the Positioning icon. Press the Select button to view
the positioning settings.
3. A pair of small arrows will indicate whether you are in Vertical or Horizontal positioning
mode. Use the Select button to toggle between Vertical and Horizontal mode.
4. Depending on your mode, the + button will shift the display either up or right. The button will shift the display either down or left.
5. Once you are happy with your position settings, allow the converter to sit idle for a
few seconds. This will save the position settings and exit the OSD automatically.
Brightness
There are four brightness levels supported by the VGA2NTSCPRO.
1. Press the Menu button to call up the OSD menu.
2. Use the +/- buttons to scroll to the Brightness icon. Press the Select button to view
the brightness settings.
3. Use the +/- buttons to set the desired brightness level.
4. Once you are happy with your brightness settings, allow the converter to sit idle for
a few seconds. This will save the brightness settings and exit the OSD automatically.
Instruction Manual
4
Color Bar
1. Press the Menu button to call up the OSD menu.
2. Use the +/- buttons to scroll to the Color Bar icon. Press the Select button to view
the color bar settings.
3. Use the +/- buttons to turn on/o the color bar.
4. When you are happy with the color bar settings press the Menu button or leave
theconverter idle to save your settings and exit the OSD.
Reset
This function will reset all your functions back to their default settings.
1. Press the Menu button to call up the OSD menu.
2. Use the +/- buttons to scroll to the Reset icon.
3. Press the Select button to return all your functions to their default settings.
Using the Remote
When using the remote control, be sure to aim the remote in the direction of the IR
receiver on the front of the converter. The functions on the remote generally operate in
a similar manner to the functions on the converter, with a few exceptions:
• There is no OSD main menu with the remote. Pressing a button on the remote
will automatically take you to the settings for that function. To toggle through
the settings for a function, press the function button. (For example, to change
the brightness settings with the remote, press the Bright button to bring up the
brightness settings on the OSD. Now toggle through the brightness settings by
pressing the Bright button again.) To save your settings and exit the OSD, leave the
remote idle for a few seconds.
• The arrow and Home buttons on the remote correspond to the Position function.
The arrow keys position the display and the Home button returns the screen to its
default position.
• The Reset button will return the Brightness and Sharpness values to their default settings.
• The Zoom button toggles between Zoom and normal modes. When in Zoom mode,
the Z-Q button scrolls between the four quadrants of the screen.
• The remote also features a Freeze button that allows you to pause the image on
your TV screen. Toggle Freeze mode on and o by pressing the Freeze button. While
in Freeze mode, your computer monitor will stay active and the Power LED on the
converter will ash. When you exit Freeze mode, the VGA signal will convert to the
TV screen as usual.
Instruction Manual
5
Troubleshooting
If you are experiencing any diculties with your converter, rst make sure that all
cables are rmly seated and connected to their proper ports.
No video output.
• Make sure the power is turned on. Your computer screen will still have a display
even if the converter is turned o, but you will not have a display on the T V unless
the converter is powered on.
• Make sure that your television is on the proper “Video Input” channel. Consult the
television manufacturer’s documentation if necessary.
• Make sure that your 15-pin VGA extender cable is attached to the proper ports.
• Make sure the Video/RGB and NTSC/PAL settings on the converter are correct.
Consult your television manufacturer’s documentation for details on your
television’s settings.
• If you are connecting from a notebook computer, make sure that the CRT output on
your notebook is enabled.
Output on TV is mono (black and white).
• Make sure the NTSC/PAL setting on the converter is correct. Consult your television
manufacturer’s documentation for details on your television’s settings.
• Make sure the color or saturation setting on your TV is not minimized. There is a line
icker on the TV.
• Adjust the Sharpness settings to nd an appropriate level for your system. My TV
doesn’t have an extra video input connector.
• You may need to purchase a special RF Modulator. This device can convert the
composite video signal of the converter into an antenna signal that can be read by
many older televisions.
Instruction Manual
6
Specications
Input Signal VGA
Horizontal Frequency 25 KHz - 58.464 KHz
Vertical Frequency 50 Hz - 100 Hz
Output Signal
Power Supply 9V DC power adapter
Weight 230g (0.51 lbs)
Dimensions
Compliance FCC Class B and CE
Composite video, S-Video, analog RGB video
for SCART, computer monitor pass-thru
Base Unit: 6.50 x 4.13 x 1.02 in. (165x 45x
26mm) Remote: 3.39 x 1.77 x 0.28 in. (86x 45x
7mm)
Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
8
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...