2 Way VGA to HDTV Converter/Scaler
VGA2TV2WAY
Instruction Guide
The Professionals’ Source For Hard-to-Find Computer Parts
VIDEO CONVERTER
* Actual product may vary from photo
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
1
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Connecting Devices to the Video Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connecting a VGA signal source to a HDTV display . . . . . . . . . . . . . . . . . . . . . .3
Connecting a HDTV signal source to a VGA display . . . . . . . . . . . . . . . . . . . . . .3
Using the Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Using the OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Tr oubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Supported Video Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Warranty Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2
Introduction
Thank you for purchasing a StarTech.com VGA to HDTV 2 way converter. This product
allows you to display your computer’s video signal on a HDTV-compatible display (such
as a LCD or plasma television) or converts a HDTV signal for display on a computer
monitor. With an easy-to-use interface and advanced conversion technology, you can
now maximize your video environment with minimum effort.
Features
• Automatic input signal detection and multiple output resolutions supports a wide
range of equipment.
• Easy to use interface gets you up and running in minutes.
• Onboard 48MB buffer for seamless frame rate conversion.
• Combines the functions of a format converter, scan converter, and video scaler in a
single product.
Before You Begin
Package Contents
•1 x VGA to HDTV 2-way converter/scaler
•1 x HD-15 male/male VGA cable
•2 x HD-15 male to YPbPr 3-prong composite RCA cable
• 1 x AC Power Adapter
•1 x User Manual
Site Preparation
Place the video converter near the source device and your display. It is highly
recommended that you use the cables provided in the package or other cables branded
by StarTech.com for the best possible performance. If you are using cables other than
those supplied in the video converter package, use the minimum amount of cable
possible to complete the connections. Excess cabling makes the signal more susceptible
to noise interference and may reduce performance. Need more cables? Contact your
dealer or visit www.startech.com for more information.
3
Connecting Devices to the Video Converter
Connecting a VGA signal source to a HDTV display
WARNING: The default output signal from the video converter is 1024 x 768 (XGA) at
60 Hz. Not all HDTV devices have the capability to display this resolution, so it is
advisable to consult the documentation for your display product befor
e attempting
installation. If your display does not support this resolution, you may not be able to
access the menu features through the on-screen display (OSD).
1. Disconnect the HDTV display from any existing video connections.
2. Disconnect the monitor or other display (if applicable) from the VGA signal source.
3. Use one of the provided HD-15 male to YPbPr 3-prong composite RCA cables and
connect the 15-pin (VGA) connector to the PC/HDTV OUT port on the rear panel of
the video scaler.
4. Connect the RCA composite connectors (red/green/blue) on the same YPbPr 3-prong
composite RCA cable to the appropriate connectors (usually marked as VIDEO IN or
similar) on the HDTV display. (This is the same set of connectors used by the previous
display that you removed in step 1, if applicable.)
5. Connect one end of the provided HD-15 male/male cable to the VGA Out connector
on the video source. (This is the same port used by the monitor you disconnected in
step 2, if applicable.)
6. Connect the opposite end of the HD-15 male/male cable to the PC/HDTV IN port on
the rear panel of the video converter.
7. Connect the AC power adapter to a suitable wall outlet. Connect the opposite end to
the DC 12V connector on the rear panel of the unit.
8. Power on both the VGA signal source and the HDTV display.
Connecting a HDTV signal source to a VGA display
1. Disconnect the HDTV signal source (i.e. satellite receiver) from any existing displays.
2. Disconnect the VGA display from any existing signal source (i.e. computer).
3. Use one of the provided HD-15 male to YPbPr 3-prong composite RCA cables and
connect the 15-pin (VGA) connector to the PC/HDTV IN port on the rear panel of
the video scaler.
4. Connect the RCA composite connectors (red/green/blue) on the same YPbPr 3-prong
composite RCA cable to the appropriate connectors (usually marked as VIDEO OUT
Rear Panel
Front Panel
4
or similar) on the HDTV source. (This is the same set of connectors used by the
previous display that you removed in step 1, if applicable.)
5. Connect the VGA connection from the VGA display to the PC/HDTV connection on
the front panel of the video converter.
7. Connect the AC power adapter to a suitable wall outlet. Connect the opposite end to
the DC 12V connector on the rear panel of the unit.
8. Power on both the HDTV signal source and the VGA display.
Using the Menu Options
The video converter uses an intuitive on-screen display (OSD) system that allows you to
fine-tune the video output to the display you are using.
By default, the video converter selects an output setting of XGA (1024 x 768 pixels, 60
Hz). If the video setting you select from the OSD menu system exceeds the capabilities
of the display you are using, you can reset the video converter to the default setting by
using the following button combination on the front panel:
Press + and - at the same time to force the unit to XGA, 60 Hz.
1. After you have connected the video source and display to the video converter using
the directions in the previous section, power on both the device and the display.
2. The display should show a bright-blue screen. Be sure that the video source is sending
a video signal to the video converter for testing purposes.
4. Once the correct a signal source is detected, the device will display the image source
on the screen. Depending on the requirements of the display, you may need to adjust
the output settings on the video scaler for best image quality. See the instructions
below for more information.
Using the OSD
The video converter automatically interprets the input resolution and scales it to the
output resolution selected in the menu system. While the default settings will provide
an image, the video scaler offers several settings that will allow you to adjust the output
signal for the best possible result.
NOTE: Changing the settings below may cause the signal to become unusable if the
settings you select are incompatible with your display. Should this occur, repeat the
steps outlined in the section above to reset the video scaler back to a compatible setting.
To activate the menu system, press the MENU key on the front of the video scaler once.
The OSD will display the available option on the left-hand side of the screen. To
navigate the menu system:
1. Use the + and - keys on the front of the video converter to move
between options.
2. Use the MENU key to select an item to adjust or display a
sub-menu.
3. Once an item is selected, use the + and - keys to adjust the
5
setting.
4. When you are satisfied with your changes, press MENU to
activate the setting.
5. You can continue to adjust other settings, or select Exit
from
the OSD menus until the OSD disappears.
The following options can be adjusted from the OSD menu
system:
Input Setup (Adjusts the sampling rate)
Clock
Phase
Output Setup (Adjusts the output resolution/refresh)
Resolution-Refresh Rate (Hz.)
Picture Adj. (Adjusts picture quality/appearance)
Contrast
Bright(ness)
Color
Red
Green
Blue
Reset
H V Adjust (Adjusts the position of the image on the display)
H Pos(ition)
V Pos(ition)
OSD Adjust (Adjusts the position of the OSD menu on the display)
H Pos(ition)
V Pos(ition)
Auto Adjust (Resets to factory default settings when selected)
System Information (Displays the current settings of the video scaler)
INPUT [Resolution-Refresh Rate (Hz.)]
OUTPUT [Resolution-Refresh Rate (Hz.)]
The video converter will store your changes until it is reset to its default settings.
NOTES:
• The System Information OSD menu does not allow you to modify any settings and
shows the current state of the video converter settings.
• The Output Setup menu allows you to adjust the output resolution and frequency of
the video converter. For more information about the resolution and refresh setting
supported by the device and correlating pixel counts for various settings (i.e. “SVGA”),
please see the “Specifications” section of the manual. You should exercise caution in
adjusting this setting, since a setting that exceeds the capabilities of your display could
cause damage in some situations. Consult the documentation for your display to
determine if the setting you wish to use is supported.
• Selecting Auto Adjust from the OSD menu is the same as using the reset procedure on
the front panel.
Input set up
Output set up
Picture Adjust
HV Adjust
OSD Adjust
System Information
Auto Adjust
Exit
6
Troubleshooting
Problem: I can’t see an image from the video source or the OSD.
Cause: The input setting or output timing (resolution and refresh rate) is incorrect.
Resolution: a) Adjust the settings back to the default setting.
b) Ensure all cables are securely connected in the proper connectors.
Problem: The image is distorted or blurry.
Cause: The output timing settings/image quality settings are not optimized, or there is
interference degrading the cable signal.
Resolution: a) Adjust the timing settings and image settings using the menu system to
improve image quality and ensure the video source is working normally.
b) Use the shortest cable length possible, and ensure that they are of a high
quality. Heavily-shielded cables with gold-plated connectors offer superior
performance and signal protection.
7
Specifications
Supported Video Modes
Bolded entries indicate that the value applies to output resolutions only. All other
modes are supported for both input and output.
PC Resolutions Vert Rate Format Scan Type
VGA 640 x 480 60/72/75/85 Hz. RGBHV Progressive
VESA85 640 x 400 85 Hz. RGBHV Progressive
VGA70 720 x 400 70 Hz. RGBHV Progressive
SVGA 800 x 600 60/72/75/85 Hz. RGBHV Progressive
XGA 1024 x 768 60/70/75/85 Hz. RGBHV Progressive
Mac 1152 x 864 70/75 Hz. RGHHV Progressive
WXGA 1280 x 768 60 Hz. RGBHV Progressive
1280A 1280 x 1024 60 Hz. RGBHV Progressive
SXGA 1280 x 1024 60/75 Hz. RGBHV Progressive
HDTV Resolutions Vert Rate Format Scan Type
480p 720 x 480 60 Hz. YPbPr, RGBHV Progressive
480i 720 x 480 60 Hz. YCbCr, RGBHV Progressive
576p 720 x 756 50/60 Hz. YPbPr, RGBHV Progressive
576i 720 x 756 50 Hz. YCbCr, RGBHV Progressive
720p 1280 x 720 60 Hz. YPbPr, RGBHV Progressive
1080i 1920 x 1080 60 Hz. YPbPr, RGBHV Progressive
Input Format RGBHV, YPbPr, YCbCr
Input Signal Levels RGB @ 0.7V p-p, 75 ohm. H&V sync @ 3-5V p-p, TTL
Y@ 1V p-p, 75 ohm. Pb,Cb,Pr,Cr @ 0.7V p-p, 75 ohm
Output Format RGBHV, YPbPr
Output Signal Levels RGB @ 0.7V p-p, 75 ohm. H&V sync @ 3-5V p-p, TTL
Y@ 1V p-p, 75 ohm. Pb,Pr @ 0.7V p-p, 75 ohm
Input/Output Connector HD-15 (female)
Controls Front panel buttons utilizing on-screen display
Weight 10 oz. (280 g)
Dimensions (H x W x D) 1.2 x 3 x 5.5 in. (30 x 75 x 140 mm)
Power Adapter 12V DC, 800 mA
8
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit our
Web site to access our comprehensive selection of online tools, documentation, and
downloads:
www.startech.com/support
Warranty Information
This product is backed by a one-year warranty. In addition, StarTech.com warrants its
products against defects in materials and workmanship for the periods noted,
following the initial date of purchase. During this period, the products may be
returned for repair, or replacement with equivalent products at our discretion. The
warranty covers parts and labor costs only. StarTech.com does not warrant its products
from defects or damages arising from misuse, abuse, alteration, or normal wear and
tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the actual
price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement
may not apply to you.
Revised: 6 April 2005 (A)
Loading...