StarTech.com USB2DVIMM6 User Manual

USB2DVIMM6

Instruction Manual

USB to DVI Video Adapter

6ft. USB 2.0 to DVI External Multi

Monitor Video Adapter Cable -

Male/Male

*Please ensure that the driver
installation is complete prior to
the physical installation of the
USB 2.0 to DVI adapter

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.•

Increase the separation between the equipment and receiver.•

Connect the equipment into an outlet on a circuit different from that to which the receiver •

is connected.

Consult the dealer or an experienced radio/TV technician for help.•

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative pur poses only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.

Table of Contents

Introduction ..................................................................... 1

Packaging Contents.....................................................................1

System Requirements .................................................................1

Installation ....................................................................... 1

Windows 2000/XP/Vista ..............................................................1

Mac OS X ....................................................................................3

Configuration .................................................................. 4

Windows 2000/XP/Vista ..............................................................4

Mac OS X ....................................................................................6

Specifications .................................................................. 9

Supported Resolutions ................................................... 9

Technical Support ........................................................... 10

Warranty Information ...................................................... 10

i

Introduction

Packaging Contents

1 x USB2DVIMM6 video adapter•

1 x Driver CD•

1 x User Manual•

System Requirements

Processor: 1.2GHz or higher clock speed•

RAM: 512MB or higher•

30MB of available disk space•

An available USB 2.0 port•

DVI capable monitor•

CD/DVD-ROM drive (driver installation)•

Microsoft Windows•
Mac OS® 10.4/10.5

®

2000/XP(32-bit)/Vista(32/64-bit) or

Installation

Please ensure that the driver installation is complete prior to *
the physical installation of the USB 2.0 to DVI adapter

Windows 2000/XP/Vista

Insert the Driver CD (included) into the CD/DVD-ROM drive.1.

Browse through the Driver CD and locate the “DisplayLink.exe” file. 2.
Double-click on the “DisplayLink.exe” file to begin the installation
process:

DisplayLink.exe

1

When the End User License 3.
Agreement appears, please
read and accept it to proceed
with the installation.

Please wait while the 4.
installation package copies
the necessary files.

Once the installation is complete, click the Restart button. The 5.
computer will automatically reboot, so please make sure to close/
save any files/programs you have opened before pressing the
button.

After Windows has loaded, plug in the USB2DVIMM6 adapter to the 6.
computer. Windows should start to automatically load the drivers.
Once complete, you should see this icon in your System Tray:

To verify the installation, right-click on “My Computer” and select 7.
Manage to open the Computer Management window. In the left
pane of the Computer Management window, click on Device
Manager. In the right pane of the Computer Management window,
click on Universal Serial Bus Controllers, and ensure that the
USB2DVIMM6 is listed underneath.

*actual device name may vary

If you wish to add additional USB2DVIMM6 adapters, simply 8.

plug them into available USB 2.0 ports. A maximum total of 5
USB2DVIMM6 video adapters can be used on a computer.

2