Manual Revision: 03/28/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
UNI3510U2EB
UNI3510UEBEU
UNI3510UEBGB
3.5 eSATA USB 2.0 to IDE SATA External
Hard Drive Enclosure
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ............................................................................................1
Packaging Contents .................................................................................................................................1
System Requirements .............................................................................................................................. 1
Hardware Guide .....................................................................................2
Front Panel ................................................................................................................................................... 2
Rear Panel .................................................................................................................................................... 2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
Driver Installation ...................................................................................................................................... 4
Software Installation ................................................................................................................................4
Recognizing the Hard Drive .................................................................6
Windows XP ................................................................................................................................................ 6
Windows Vista ............................................................................................................................................ 7
Specications ..........................................................................................8
Technical Support ..................................................................................9
Warranty Information ............................................................................9
Instruction Manual
1
Introduction
This enclosure lets you turn almost any high capacity 3.5” Serial ATA (SATA) or IDE hard
drive into an eSATA (SATA only) or USB (SATA or IDE) external hard drive, allowing you
to customize your external storage solution based on your preference of hard drive
model and manufacturer.
Packaging Contents
• Hard Drive Enclosure
• USB Mini B Cable
• eSATA Cable
• IDE Cable
• Driver CD
• Enclosure Stand
• Power Adapter
• SP4 to LP4 Adapter Cable
• SATA 7+15 pin cable
System Requirements
• Available USB 2.0 or eSATA port on computer system
• Microsoft® Windows® 2000/XP/Vista/Server 2008 R2/7 (32/64-bit)
• Apple® Mac OS® 9.x/10.x, or Linux® kernel 2.4.1.0 and above
Instruction Manual
2
Hardware Guide
Front Panel
Rear Panel
1
2
3
4
1
2
1. Power Button/LED
2. Backup Button
1. DC In Port
2. eSATA Port
3. Mini USB Port
4. Hard Drive Release Switch
Instruction Manual
3
Installation
Hardware Installation
1. Open the hard drive enclosure by pushing the rear panel release button to the right
and sliding the hard drive bracket out of the external casing from the front.
2. If using an IDE/ATA hard drive, ensure that the hard drive you are using is set to MASTER.
3. Pull the two tabs on either side of the hard drive holding mechanism up, then
connect the provided SATA or IDE data and power supply cables to the rear ports of
the drive.
4. SATA HDD: If you will be using the USB 2.0 interface to connect to the enclosure,
plug the SATA data cable into the port labelled CN5 on the enclosure’s PCB board.
If using the eSATA interface to connect to the enclosure, plug the SATA data cable
into the port labeled CN6 on the enclosure’s PCB board. The locations of the CN5
and CN6 ports are shown below. Plug the power connector into the J1 port on the
PCB board.
Instruction Manual
4
5. IDE HDD: Only the USB 2.0 interface is available for connecting an IDE hard drive to
the host computer. Plug the 40-pin IDE data cable into the port labelled CN1 on the
enclosure’s PCB board. Plug the included 4-pin SP4 to LP4 power adapter cable into
the J1 connector.
6. To mount the hard drive, place it into the holding tray and press the tabs on either
side down to secure the drive in the enclosure.
7. Slide the hard drive holding mechanism into the external casing, ensuring that the
release button on the rear panel returns to its original, locked position.
Driver Installation
Windows® 2000/XP/Vista/7, Mac OS® 9.x/10.x, Linux Kernel® 2.4.x +
No driver installation is required for these operating systems, as this enclosure is
natively supported, so the drivers are already installed.
CN5
CN6
J1 CN1
Instruction Manual
5
Software Installation
The following steps outline the procedure to install the software included with your
drive enclosure in Windows.
1. Insert the Drivers CD into your computer’s CD-ROM. Open the DRIVERS.exe
application to begin the installation process.
2. Once the installer is running, there are a number of options available to you from
the DRIVERS.exe home screen. To install the backup software, click Install Backup
Program under the heading that corresponds with your drive-type (IDE or SATA).
3. The PCClone EX Lite Installer window will appear. Click Install to proceed with the
installation process.
4. The License and Warranty Agreement will appear. To continue, click Agree.
Instruction Manual
6
1. Click Browse to designate the directory in which the software will be installed. Once
you have made your selection, click Install to continue.
2. The installation will now take place. Once the installation is complete, you may exit
the DRIVERS.exe application.
Recognizing the Hard Drive
Windows XP
USB 2.0
If you are using the USB 2.0 interface to connect the hard drive enclosure to your
computer, no setup is required. Simply plug the hard drive enclosure into an available
USB port and turn the power on to the hard drive enclosure. Open My Computer and
the drive should be visible under the heading “Devices with Removable Storage.”
Instruction Manual
7
eSATA
If you are using the eSATA interface to connect the hard drive enclosure to your
computer, there are two setup processes you can follow. If the hard drive enclosure
is powered on upon booting up the computer, it will automatically detect the drive.
Otherwise, if you connect and power on the hard drive enclosure once the computer
has already been booted up, you will need to open the Device Manager to scan for it.
The following directions outline the necessary steps to access your hard drive when
the computer has already been booted up:
1. Right click My Computer and click Manage.
2. In the left pane, select Device Manager.
3. In the Device Manager window, click the + next to the Disk Drives icon. Since your
drive was not powered on during the boot up process, it should not yet be visible.
4. Turn on the hard drive enclosure. Once the power indicator is illuminated, click the
Scan button.
5. The Device Manager will scan for plug and play hardware. Once it has completed
the scan, your drive should be visible below the Disk Drives heading.
Windows Vista/7
USB 2.0
If you are using the USB 2.0 interface to connect the hard drive enclosure to your
computer, no setup is required. Simply plug the hard drive enclosure into an available
USB port and turn the power on to the hard drive enclosure. Open My Computer and
the drive should be visible under the heading “Devices with Removable Storage.”
Instruction Manual
8
Specications
Bus Interface
SATA 3.0Gb/s
USB 2.0
Chipset ID JMicron JMB20337
External Connectors
1 x eSATA connector*
1 x USB Mini B connector
1 x DC Power connector
Internal Connectors
2 x SATA 7-pin
1 x SATA Power 15-pin
1 x 40-pin IDE/ATA
1 x LP4 Power 4-pin
Maximum Data Transfer Rate
3.0 Gb/s (eSATA)
480 Mb/s (USB 2.0)
Fans 1 x 80mm
Power Adapter 12VDC, 2000mA, type M plug
Enclosure Material Aluminum
Operating System Support
Windows® 2000/XP/Vista/Server 2008 R2/7,
Mac OS® 9.x/10.x,
Linux Kernel® 2.4.x +
Instruction Manual
9
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...