StarTech.com SV431DPUA User Manual

2/4 Port USB DisplayPort® KVM Switch with Audio
SV231DPUA / SV431DPUA
DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 01/13/2015
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Instruction Manual
Table of Contents
Introduction ...........................................................................................1
Features ........................................................................................................................................................1
Package Contents .................................................................................................................................... 1
System Requirements .............................................................................................................................. 1
Installation ..............................................................................................1
Hardware Installation .............................................................................................................................. 2
Driver Installation ...................................................................................................................................... 5
Operation ................................................................................................5
Front Panel ...................................................................................................................................................5
Port Selection Button .............................................................................................................................. 6
AutoScan ...................................................................................................................................................... 6
Scan Time ..................................................................................................................................................... 6
HotKey Control .......................................................................................6
Auto Scan ..................................................................................................................................................... 7
Manual Scan ............................................................................................................................................... 7
Alternative Hotkey Commands ............................................................................................................ 9
Change Leading Hotkey ......................................................................................................................... 10
Specications ..........................................................................................11
Technical Support .................................................................................. 13
Warranty Information ............................................................................13
Instruction Manual
i
Introduction
Features
• Easy installation, no drivers required
• Supports Plug and Play and hot swap to save time from rebooting the computer
• Supports data transfer rates up to 480Mbps when used on a USB 2.0 port
Package Contents
• SV231DPUA or SV431DPUA KVM switch
• Power Adapter
• Rubber Feet
• Instruction Manual
System Requirements
• DisplayPort enabled computer system/video card
• USB enabled computer system
• DisplayPort enabled display device (e.g. monitor, projector, TV, etc.)
• Standard 104-key wired USB keyboard
• Standard 3-button wired USB mouse
Installation
NOTE: Prior to the installation, please power o all devices that will be connected to this system. Ensure that all devices you will connect are properly grounded. Place cables away from uorescent lights, air conditioners, and machines that are likely to generate electrical noise.
If you experience any problems using a USB KVM switch, the following BIOS setup changes may be necessary for PC users and not necessary for Mac users:
• Set HALT ON ERROR to ALL BUT KEYBOARD.
• In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set USB IRQ to ENABLED.
Dierent systems may use dierent naming, so contact your system manufacturer for further assistance with these settings.
Instruction Manual
1
Hardware Installation
Front View - SV231DPUA
Port Selection/Link LED
Rear View - SV231DPUA
Instruction Manual
Port Selection
Button
2
Front View - SV431DPUA
Rear View - SV431DPUA
Port Selection/Link
LED
Power
LED
Port Selection
Button
Instruction Manual
3
*installation pictures are representations only
1. Plug a monitor into the Console’s DisplayPort connector; plug a USB keyboard and a USB mouse into the dedicated USB keyboard and mouse ports on the KVM switch. If using audio, also connect speakers and/or a microphone with 3.5mm mini-jack plugs.
2. Use a male-to-male DisplayPort video cable to connect the DisplayPort connector on the computer’s video card, to one of the KVM’s PC ports (i.e. PC1)
3. Use a USB type A-B Cable to connect the KVM’s USB port (type B, square connector) for the PC port used in Step 2, and the USB port on the computer (type A, at connector). If using audio, connect 3.5mm mini-jack cables from the PC port to the computer sound card.
NOTE: A DisplayPort + USB + Audio KVM combo cable is also available which can be
Instruction Manual
4
used in place of separate individual cables, StarTech.com ID: DP4N1USB6.
4. Repeat for Steps 2 and 3 for each PC port on the KVM switch, or each computer you wish to use on the KVM.
5. OPTIONAL: Connect any other USB peripherals you wish to share between the connected computers/devices to the extra USB Hub ports on the Console side.
6. Connect the external power adapter from a wall outlet to the power connector on the rear panel of the KVM switch. The Power LED should light up solid and/or the LED for the selected PC port.
7. Power up the rst computer/device and wait for it to fully boot and test keyboard/ mouse functionality.
8. Once operation has been successfully conrmed, switch to the next port and power up that computer/device and conrm.
9. Once completed for all computers/devices connected to the KVM switch, you should be able to switch between ports freely.
Driver Installation
No driver installation is required for the KVM switch, as the keyboard and mouse use generic USB keyboard/mouse drivers that are already installed on any operating system that fully supports USB.
Operation
Front Panel
Port Selection/Link LED
The LED turns green when the connected computer is powered-on. The corresponding LED will also illuminate red when that PC port is currently selected.
Instruction Manual
5
Port Selection Button
2-Port: Pressing the front panel “Select” button will toggle between the two ports on the KVM switch.
4-Port: Each push button on the front panel corresponds with a PC port. Pressing that button will immediately select that port.
AutoScan
The system automatically scans through the power-on computers in sequence with a xed interval (see Scan Time below).
4-Port: To activate AutoScan, press front panel push buttons “3” and “4” simultaneously. The port selection LED will ash during AutoScan. AutoScan will select active computers only. To exit AutoScan mode, just press any one of the front panel push buttons.
Scan Time
Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15 and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
4-Port: To change the Scan Time, press front panel buttons “1” and “2” simultaneously. The unit will respond with beep(s) of 1, 2, 3 or 4 times for a Scan Time of 3, 8, 15 or 30 seconds respectively.
HotKey Control
A Hotkey command is a short keyboard sequence for selecting a computer, activating computer scan, etc. A hotkey sequence starts with two left <CTRL> keystrokes (successively within 0.2 seconds) followed by one or two more keystrokes. A built-in tone generator creates a high-pitch beep for correct hotkey command; otherwise, one low-pitch beep is generated for errors and the bad key sequence will not be forwarded to the selected computer.
NOTE: Press and hold Left <SHIFT> and press <NumLock> twice, then release <SHIFT> followed by pressing left <CTRL> once, which will enable / disable the hotkey feature.
Instruction Manual
6
To select a computer:
Left <CTRL> + Left <CTRL> + <1>
(Example: Selects the computer at port 1.)
Left <CTRL> + Left <CTRL> + <2>
(Example: Selects the computer at port 2.)
NOTE: Do not use the keypad on the right-side of the keyboard.
Auto Scan
The KVM automatically scans through the powered-on computers in sequence on a xed time interval (see Scan Time below).
Note: The keyboard and mouse are not operable during Auto Scan.
To start Auto Scan:
Left <CTRL> + Left <CTRL> + <F1>
To abort the Auto Scan mode, press the left <CTRL> key twice. When Auto Scan detects any keyboard or mouse activity, it suspends the scanning till the activity stops; it then resumes with the next computer in sequence. The length of the Auto Scan interval (Scan Time) is adjustable, see below.
Manual Scan
Manual Scan allows users to manualls switch back and forth between powered-on computers.
Left <CTRL> + Left <CTRL> + <F2>
To select the previous or the next computer, press <UP> or <DOWN> arrow keys. To abort the Manual Scan, press any other key.
Instruction Manual
7
Scan Time
Four options are available for users to set the Scan Time duration, it includes 3, 8, 15 and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
To adjust Scan Rate, set the scan time of duration before switching to the next computer:
Left <CTRL> + Left <CTRL> + <F3>
The KVM Switch generates 1 to 4 beeps indicating a scan time duration for 3, 8, 15 or 30 seconds respectively.
Audio Lock
There are two options for Audio Lock: ON and OFF. When ON, audio selection follows computer selection. When OFF, audio selection stops following computer selection. It is useful if you want to listen to a particular computer’s audio signal while operating other computers.
Left <CTRL> + Left <CTRL> + <F5>
The KVM switch beeps once or twice corresponding to ON and OFF respectively.
To change which computer port the audio stays on to the currently selected port, press the following hotkey:
Left <CTRL> + Left <CTRL> + <A>
Instruction Manual
8
Alternative Hotkey Commands
In addition to the Left <CTRL> + Left <CTRL> hotkeys, there are two
alternative hotkey sequences available.
1. 1. For the following operations, users may press <ScrollLock> twice instead of pressing left <CTRL> twice.
To select a computer:
<ScrollLock> + <ScrollLock> + <1>
(Example: Select the computer at port 1.)
<ScrollLock> + <ScrollLock> + <2>
(Example: Select the computer at port 2.)
NOTE: Do not use the keypad at the right of the keyboard.
Instruction Manual
9
2. For those keyboards that do not have or support <ScrollLock>, please press and HOLD the Left <SHIFT> and press <NumLock> twice instead of pressing Left <CTRL> twice.
To select a computer:
hold Left <SHIFT> + press <NumLock> + press <NumLock>
then release <SHIFT> + press <1>
Example: Select the computer at port 1.)
hold Left <SHIFT> + press <NumLock> + press <NumLock>
then release <SHIFT> + press <2>
(Example: Select the computer at port 2.)
NOTE: Do not use the keypad at the right of the keyboard.
Change Leading Hotkey
The default leading hotkey sequence involves pressing the left <CTRL> twice in succession (e.g. left <CTRL> + left <CTRL>). This can be changed to the right <CTRL> key instead, to avoid accidental activation due to using the left <CTRL> key for functions such as Copy/Paste.
To change the leading hotkey sequence to Right <CTRL>:
Left <CTRL> + Left <CTRL> + hold <ALT> + press Right <CTRL>
All hotkey commands that previously required pressing the Left <CTRL> will be switched to requiring the right <CTRL> instead.
To change the leading hotkey sequence back to Left <CTRL>:
Right <CTRL> + Right <CTRL> + hold <ALT> + press Left <CTRL>
Instruction Manual
10
Specications
SV231DPUA SV431DPUA
Number of Ports 2 4
Computer Connectors (per port)
Console Connectors
LEDs 2 x Port Select/Power
Maximum Video Resolution
Switching Modes Front Panel Button, Hotkey
Rack Mountable No Yes (optional kit)
Cascadable No
On Screen Display No
DDC2B Support Yes
Audio Yes
Enclosure Material Metal
Power Adapter 9-12VDC, 1.5A
(higher resolutions may be supports at lower refresh
1 x DisplayPort
1 x USB type B
2 x 3.5mm mini-jack
1 x DisplayPort
1 x USB type
2 x 3.5mm mini-jack
1 x Power
4 x Port Select/Power
2560 x 1600 @ 60Hz
rates)
Instruction Manual
11
SV231DPUA SV431DPUA
Operating
Temperature
0°C ~ 40°C (32°F ~ 104°F)
Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F)
Humidity 0 ~ 80% RH
Dimensions (WxHxD)
160.0mm x 44.0mm x
100.0mm
220.7mm x 44.0mm x
130.6mm
Weight 1050g 1100g
Instruction Manual
12
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a three year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Instruction Manual
13
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...