Manual Revision: 10/21/2013
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
RACKCOND17HD
RKCOND17HDGB
1U 17in 1080p Dual Rail LCD Rack Console
with Front USB Hub
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Front View .................................................................................................................................................... 1
Rear View ......................................................................................................................................................1
Introduction ............................................................................................ 2
Packaging Contents .................................................................................................................................2
Front Panel Controls ..............................................................................2
Installation ..............................................................................................3
Rack Installation......................................................................................................................................... 3
PC / Server Connection ........................................................................................................................... 5
Connecting to a KVM Switch ................................................................................................................5
Operation ................................................................................................5
Dual Rail Slide ............................................................................................................................................. 6
Fingerprint Reader ....................................................................................................................................7
Specications .......................................................................................... 10
Technical Support ..................................................................................11
Warranty Information ............................................................................ 11
Instruction Manual
1
Product Diagram
Front View
Rear View
Keyboard Tray Handle
USB 2.0 Hub Ports
Power Switch
Fingerprint
Reader
Menu Buttons
Key Lock
Top Handle
USB 2.0 Hub Ports
Power Switch
Hidden Keyboard Tray Handle
Top Handle
USB Hub PC
Connection
PS/2 - USB
Selector Switch
Modular KVM
Dock Port
DC
Jack
PC/KVM
Connections
Instruction Manual
2
Introduction
Packaging Contents
• 1 x Dual Rail Rack Console
• 1 x Set, Mounting Rails
• 1 x VGA USB KVM Cables
• 2 x USB A to A Cables
• 1 x DVI-I Cable
• 1 x VGA PS/2 KVM Cable
• 2 x Blockers w/ screws
• 6 x 6mm Flat Screws
• 2 x Keys
• 1 x NA Power Cord
• 1 x Power Adapter
• 1 x Instruction Manual / Software CD
Front Panel Controls
Controls Description
Soft power on/o button. Adjacent LCD is lit when on.
Auto
Auto-synchronize and scale down display to any valid
factory preset timings.
Up Press to scroll the function you want to adjust.
Down Press to scroll the function you want to adjust.
Menu
To access the main menu. This button also acts as
the “Enter” button.
Power Indicator
GREEN
RED
RED
RED
ON
STANDBY
SUSPEND
OFF
Instruction Manual
3
2. Secure the front and rear brackets onto the rack using screws and cage nuts
appropriate to your rack (not included).
Installation
Rack Installation
NOTE: The cabinet depth must be within 22.4 – 34.2” (570 - 870 mm).
1. Adjust rail with rear bracket to t your rack.
3. Repeat steps 1-2 for the other side.
Instruction Manual
4
4. Slide the console into the rails and leave about 5-10cm of space to install the
blockers.
5. Install one of the Blockers onto the back of the console as shown, and use the
included screw to secure it. Repeat on the other side.
Instruction Manual
5
6. Install three of the included 6mm Flat Screws to secure the console to the bracket.
Repeat on the other side to complete the installation.
PC / Server Connection
1. Turn o the PC / Server you are connecting to the console.
2. Using one of the included cable sets, connect the appropriate video (VGA / DVI)
connector to the video output of your PC / Server. Then connect either the PS/2
keyboard/mouse connectors, or use the USB interface.
3. Connect the other end of the cables to the rear of the console.
NOTE: Move the PS/2-USB Selector Switch on the rear of the console to either side
to select your desired interface
4. Connect the USB Hub connector using one of the included USB A-A cables to the
USB connector on your server / KVM switch to enable the front USB hub ports and
ngerprint reader (optional).
5. Connect the AC to DC power adapter to the power inlet on the console and then to
a power outlet.
Connecting to a KVM Switch
When cascading with a KVM switch, KVM Module can be used to control additional
computers from the console. The connection is exactly the same as is shown above
(see PC / Server Connection section above). The only dierence is the connection
would be made to the “CONSOLE PORT” of the KVM switch instead, of a computer.
Instruction Manual
6
Operation
1. Once all cables are securely connected and all mounting screws are properly
tightened, loosen the thumbscrews on the front of the console.
2. Grasp the Top Handle and pull the console outward and then lift upward to open.
3. Turn the Power Switch on the front of the console to the On position, and power on
the connected Server or KVM switch.
NOTE: There is also a soft Power On/O button located with the menu controls
below the LCD panel. If the display does not turn on automatically, press the power
button
4. Use the OSD controls to adjust the image as necessary – see the Front Panel
Controls section above for instruction.
Instruction Manual
7
Dual Rail Slide
The dual-rail console design allows the LCD display and keyboard/mouse to slide
independently from the keyboard/touchpad tray.
1. With the console lid open (keyboard tray can be in the rack or pulled out), grab both
sides of the LCD panel at the bottom and pull towards you to slide the LCD forward.
2. You can then disengage the locks on the keyboard tray rails to slide the console
back into the rack if desired, leaving the LCD panel visible.
Instruction Manual
8
Fingerprint Reader
Once installed, the ngerprint reader software oers several options to congure
biometric access, application / le launching and virtual secure storage drives.
Windows
1. Insert the included CD and navigate to your CD/DVD drive to install the included
ngerprint reader application. The software will create an icon in your system tray.
NOTE: You may be prompted to restart after the install
2. Open the software to view the main menu window. The following sections will
provide instruction on the options available.
Finger Convenience:
Enrollment – Lets you enroll one or more
ngerprints.
Instruction Manual
9
Password Bank Management – Manages passwords for both websites
and applications.
Finger Launch Management – Congures application or le launch at the
swipe of a nger.
Data Protection:
Change Default Password – Create or change a default password for data encryption.
Yo-Safe Management – Create and manage a secure virtual disk.
Instruction Manual
10
Advance Settings:
BioExcess™ Functions Settings – Enable or disable Fast User Switching for all
accounts.
Data Backup – Backup enrolled ngerprints and Password Bank items.
Data Restore – Restore backed up data from a le.
Information:
About – Display software version information
Help – Access help les
Tutorial – Launch software tutorial
Instruction Manual
11
Specications
Display Size 17.3”
Panel Type Active Matrix TFT LED
Maximum Screen Resolution 1920x1080 (Full HD)
Supported Platforms USB or PS/2
Server / KVM Video Type DVI or VGA
Response Time 2ms
Contrast Ratio 650:1
Brightness 300cd/m²
Viewing Angle 140° (H), 120° (V)
Pixel Pitch 0.264 x 0.264 mm
Keyboard/Mouse 106-key USB keyboard with touchpad
Console Interface(s)
2x PS/2 (6 pin; Mini-DIN)
1x VGA (15 pin; High Density D-Sub)
1x DVI-I (29 pin)
2x USB A (4 pin)
Other Interface(s) 2x USB A (4 pin)
Chassis Material Heavy-duty steel
Minimum/Maximum Mounting
Depth
22.4 x 34.2 inches (570 – 870 mm)
Power Supply 100~240V AC Input
Power Consumption 10.2W
Operating Temperature 0°C to 50°C (32°F to 122°F)
Storage Temperature -20°C to 60°C (-4°F to 140°F)
Humidity 10~90% RH
Dimensions (LxWxH) 21.2 x 17.6 x 1.7 inches (540 x 448 x 44 mm)
Weight 28.7 lbs (13 kg)
Instruction Manual
12
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...