Wireless Travel Router for iPad® - USB
Powered with Charge Port
R150WN1X1T
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 04/08/2014
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try correct
the interference by one or more of the following measures:
1. Reorient the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into and outlet on a circuit dierent from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specied in the instruction manual.
WARNING: A shielded-type power cord is required in order to meet FCC emission limits and
also to prevent interference to the nearby radio and television reception. It is essential that
only the supplied power cord be used. Use only shielded cables to connect I/O devices to this
equipment.
CAUTION: Any changes or modications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
FCC ID: JY8DW06
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.This
device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Instruction Manual
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
Déclaration d’exposition à la radiation:
Cet équipement respecte les limites d’exposition aux rayonnements IC dénies pour un
environnement non contrôlé. Cet équipement doit être installé et mis en marche à une
distance minimale de 20 cm qui sépare l’élément rayonnant de votre corps.
L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver à
leur proximité.
IC: 11232A-R150WN1X1T
IC statement CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
Table of Contents
Introduction ............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements .............................................................................................................................. 1
Product Overview ..................................................................................1
LED Indicator .............................................................................................................................................. 2
Reset Button ................................................................................................................................................ 2
Installation .............................................................................................2
Default Settings ......................................................................................................................................... 2
Hardware Installation .............................................................................................................................. 2
Web Interface ............................................................................................................................................. 3
Specications ..........................................................................................6
Technical Support .................................................................................. 7
Warranty Information ............................................................................7
Instruction Manual
i
Introduction
Packaging Contents
• 1 x Travel Router
• 1 x USB Extension Cable
• 1 x Instruction Manual
System Requirements
• iPad charger, or other USB power adapter / charge port
• Wired network connection
Product Overview
Instruction Manual
1
LED Indicator
Power (Green) The AP is powered on
Wi (Red) Wi is operational
Reset Button
In order to reset the device to factory defaults:
1. Ensure the AP is connected to a power source.
2. Press and hold the reset button for 3 seconds (the red Wi LED will turn o),
then release.
Installation
Default Settings
SSID: ComWi_xxxxxx
IP Address: 10.10.1.1
Hardware Installation
1. Connect an Ethernet cable to the WAN port on the bottom of the AP (with the
other end connected to the hotel wall jack/switch).
2. Slide the AP over your iPad power adapter and plug into a wall outlet, or use the
included USB extension cable to power the device through an available USB port /
other USB wall charger.
3. Connect your iPad / wireless devices to the “ComWi_xxxxxx” SSID and open
your web browser to access the Internet.
NOTE: If your hotel Internet requires a password or has a captive portal login,
contact the front desk to obtain that information from them.
Instruction Manual
2
Web Interface
Once connected to the “ComWi_xxxxxx” SSID , you are able to congure security
settings for the WiFi connection and adjust settings / operating modes using
a standard web browser. The Setup Wizard will guide you through the basic
requirements to congure and secure your AP.
NOTE: It is recommended to secure your wireless access point in public locations
to avoid unwanted access and/or conguration changes.
1. Open your desired web browser and enter http://10.10.1.1/ into the address bar.
2. Select the Operation Mode that ts your application (default: Gateway), then
click Next.
3. If you would like to change the default IP address of the R150WN1X1T device,
enter a new IP here, or click Next.
Instruction Manual
3
4. Select your WAN interface setting such as DHCP (default), PPPoE, PPTP or L2TP, then
click Next.
5. Congure your Wi-Fi settings as desired, then click Next.
6. Choose your desired encryption and create a wireless key for secured access, then
click Next.
Instruction Manual
4
7. To restrict access to the web interface of your AP, it is also recommended to
congure a password, which can be done by selecting Management, then
Password from the left column of the web page.
Instruction Manual
5
Specications
Antenna Conguration 1x1:1(TxR:S)
Supported Standards
External Ports
Internal Ports 1 x USB A (4 pin) Male
Max. Data Transfer Rate 150 Mbps
Wireless Frequencies 2.4 ~ 2.4835 GHz
Supported Security Schemes WEP, WPA, WPA2, TKIP/AES
Max. Distance 10 m / 33 ft
Modulation
Compatible Networks 10/100 Mbps (Wired)
Operating Temperature 0°C to 55°C (32°F to 131°F)
Storage Temperature -20°C to 55°C (-4°F to 131°F)
Humidity 0~90% RH (Non-Condensing)
Dimensions 47 x 55 x 35 mm
Weight 335 g
IEEE 802.11b, IEEE 802.11g, IEEE 802.11n,
IEEE 802.3, IEEE 802.3u
1 x USB A (4 pin) Female
1 x RJ-45 Female
DSSS (BPSK/QPSK/CCK), OFDM (BPSK/
QPSK/16QAM/64QAM)
Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
7
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...