StarTech.com PEX4S553S User Manual

4 Port PCI Express RS232 Serial Card with Power Output and 15kV ESD Protection
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 06/03/2013
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Instruction Manual
Table of Contents
Introduction ............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements .............................................................................................................................. 1
Product Overview ..................................................................................2
Jumper Settings ......................................................................................................................................... 2
IDC Header Pinout ....................................................................................................................................4
Installation ..............................................................................................4
Hardware Installation ..............................................................................................................................4
Driver Installation ...................................................................................................................................... 5
Verifying Installation ................................................................................................................................ 6
Specications ..........................................................................................7
Technical Support ..................................................................................8
Warranty Information ............................................................................8
Instruction Manual
i
Introduction
The PEX4S553S 4-Port PCI Express Serial Card lets you add four ESD-Protected (15kV) RS232 ports, with 5V or 12V selectable power output through a PCI Express slot.
Packaging Contents
• 1 x Serial Card
• 1 x Breakout Cable
• 1 x Low Prole Bracket
• 1 x Driver CD
• 1 x Instruction Manual
System Requirements
• Available PCI Express slot
• Available SP4 power connector (if additional power is required that can’t be supplied through the PCI Express slot)
• Windows® 8 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), 2000, Windows® Server 2008 R2, 2003(32/64), Linux
Instruction Manual
1
Product Overview
Power over Serial Enable/Disable jumpers (per-port)
DB44 External Connector
4-port DB44 to DB9MX4 Breakout Cable
Jumper Settings
Power over serial Enable/Disable (per-port):
DISPWR
Each port can be individually congured to provide
S1
S2
S3
S4
power over Pin 9, or not.
“DIS” (far right – factory default) position: Pin 9 will not provide power.
“PWR” (far left) position: Pin 9 will provide the auxiliary power specied using the Aux Power Source Selector jumpers (outlined below)
Aux Power Source Selector
SP4 Aux Power Connector
S1~S4 Internal header Connector
Instruction Manual
2
Aux power source selection:
X5V
X12V
I12V
X5V
X12V
I12V
X5V
X12V
I12V
RS232 Pinout
X5V: DC5V, from SP4, an SP4 power connection is required
X12V: DC12V, from SP4, an SP4 power connection is required
I12V (factory default): DC12V, from PCI Express slot,
Pin 1 DCD
Pin 2 RXD
Pin 3 TXD
Pin 4 DTR
Pin 5 GND
Pin 6 DSR
Pin 7 RTS
Pin 8 CTS
Pin 9 RI
NOTE: Pin 9 of the DB9 connector will output DC power if the corresponding jumper
was enabled.
Instruction Manual
3
IDC Header Pinout
The internal IDC header connectors can be used in place of some / all external ports on this card. They are labeled S1 – S4 and each corresponds to the external port of the same number (marked on the breakout cable). Do not connect the internal and external port of the same number simultaneously.
Pin# Signal Pin# Signal
1 DCD 6 DSR
2 10
1 9
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI (*)
5 GND 10 NC
Installation
WARNING! PCI Express cards, like all computer equipment, can be severely damaged by static electricity. Be sure that you are properly grounded before opening your computer case or touching your PCI card. StarTech.com recommends that you wear an anti-static strap when installing any computer component. If an anti-static strap is unavailable, discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds. Also be careful to handle the card by its edges and not the gold connectors.
Hardware Installation
1. Turn your computer o and any peripherals connected to the computer (i.e. Printers, external hard drives, etc.). Unplug the power cable from the rear of the power supply on the back of the computer and disconnect all peripheral devices.
2. Remove the cover from the computer case. Refer to documentation for your computer system for details.
3. Locate an open PCI Express slot and remove the metal cover plate on the rear of the computer case.
4. Gently insert the card into the open PCI Express slot and fasten the card’s bracket to the rear of the case.
NOTE: If installing the card into a low prole system, replacing the pre-installed standard prole bracket with the included low prole bracket may be necessary.
Instruction Manual
4
5. (Optional) Connect an available SP4 power connection from your system power supply to the card if additional power is required.
6. Place the cover back onto the computer case.
7. Connect the 4 Port breakout cable to the large connector on the card.
8. (Optional) If using the IDC header connections instead of some / all of the external ports, connect them to the appropriate header(s), noting proper orientation of the cable using the pinout provided above
NOTE: Do not connect the matching internal and external port simultaneously. The IDC headers are labeled S1 – S4 and correspond with the numbered ports on the breakout cable.
9. Insert the power cable into the socket on the power supply and reconnect all other peripherals removed in Step 1.
Driver Installation
1. Upon starting Windows, if the Found New Hardware wizard appears on the screen, cancel/close the window and insert the included Driver CD into the computer’s CD/ DVD drive.
2. AutoPlay should automatically launch and display all of the folders on the CD. If not, open the Computer (My Computer in Windows XP/Server 2003) and double-click on the CD/DVD drive.
3. Navigate to X:\IO\MOSCHIP\MCS99xx (where X:\ is your CD/DVD drive letter) and then choose the appropriate folder for the operating system you are installing on.
4. Where applicable, choose 32bit or 64bit depending on your operating system
5. Double-click the le StnSetup.exe application and the drivers will automatically install.
Instruction Manual
5
Verifying Installation
1. Open the Device Manager by right-clicking on Computer, and then select Manage. In the new Computer Management window, select Device Manager from the left window panel (For Windows 8, open the Control Panel and select Device Manager).
2. Expand the Multifunction Adapters and Ports (COM & LPT) sections. On a successful install, you should see 4 PCIe to Multifunction Peripheral Controller devices in the Multifunction Adapters section, and 4 PCIe to High Speed Serial Port (COMx) devices installed with no exclamation points or question marks.
Instruction Manual
6
Specications
Host Interface PCI Express
Form Factor Standard Prole (Low Prole bracket incl.)
Chipset ID ASIX/MOschip - MCS9904
External Connectors 4x DB-9 (9 pin; D-Sub)
Supported Protocols RS-232
Maximum Baud Rate 921.6 Kbps
ESD Protection 15kV
Data Bits 5, 6, 7, 8, 9
Parity Even, Odd, Mark, Space, None
Stop Bits 1, 1.5, 2
Flow Control None, Xon/Xo, RTS/CTS
Operating Temperature 0°C to 55°C (32°F to 131°F)
Storage Temperature -20°C to 85°C (-4°F to 185°F)
Humidity 5~95% RH
Dimensions 66 x 18 x 87 mm
Weight 350 g
Compatible Operating
Systems
Windows® 8 (32/64bit), 7 (32/64), Vista(32/64),
XP(32/64), 2000, Windows® Server 2008 R2,
2003(32/64), Linux
Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a lifetime warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Instruction Manual
8
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...