Industrial 4 Port RS232/422/485 to Dual
Ethernet Serial Device Server - PoE PD
NETRS42348PD
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 11/22/2013
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s authority
to operate the equipment.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Front View ....................................................................................................................................................1
Terminal Block Power Connector ........................................................................................................ 2
The server can be installed on a DIN rail or it can be wall-mounted.
Installation on a DIN-Rail:
1. Tilt the unit, making sure that the metal spring located at the back is positioned on
top of the DIN rail.
2. Push the unit towards the rail until a “click” sound is heard.
Installation on a Wall:
1. Remove the DIN-rail kit preinstalled on the unit.
2. Install the wall-mount panel included using the 6 screws found in the package.
3. Mount the unit on the wall using the appropriate hardware for the surface you are
mounting to.
Instruction Manual
4
Software Installation
1. Insert the provided CD into your DVD/CD-ROM drive.
2. Browse to the folder “fscommand\Utility\DS-Tool” and execute the installer
“Startech_V1.0_xxxxxxx”
3. Follow the on-screen instructions to complete the installation.
Operation
For full operating instructions, please visit www.startech.com/NETRS42348PD
1. Start the DS-Tool, allow the install of the driver
2. Allow access to the DS-Tool on the Windows Firewall
Instruction Manual
5
3. Once the utility opens, click the “Broadcast” button to detect the device server. The
default IP address of device is “192.168.10.2”.
4. Once detected, click the checkbox beside the device you would like to congure,
then click the “Add” button to congure your desired IP settings (Static / DHCP).
To add a virtual COM port, please use the VCOM Wizard and follow the steps.
Instruction Manual
6
Specications
InterfaceSerial
Ports4
Supported Protocols
Connectors
LED Indicator(s)
Supported Serial ProtocolsRS232/422/485
Ethernet Link Speed10/100 Mbps
Maximum Baud Rate460.8 Kbps
Power InputTerminal Block: 12~48VDC
Enclosure MaterialMetal
Operating Temperature-10 to 70°C (14 to 158°F)
Storage Temperature-40 to 85°C (-40 to 185°F)
Humidity5% to 95% Non-condensing
Dimensions106.1mm x 52mm x 144.3 mm
Weight682 g
Compatible Operating Systems
ICMP, IP, TCP, UDP, DHCP, BOOTP, ARP/RARP,
DNS, SNMP MIB II, HTTPS, SSH
4x DB-9 male,
1x Power over Ethernet RJ-45
1x 6pin Terminal Block
2x Ethernet Link, P.O.E, PWR1,PWR2, fault,
Windows® 8 (32/64bit), 7 (32/64),
Vista(32/64), XP(32/64),Windows® Server
2012, 2008 R2, 2003(32/64)
1x RJ-45
S1, S2, S3, S4
Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a ve year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
8
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.