StarTech.com MCM110ST2 User Manual
Instruction Manual
10/100 Ethernet to Multi Mode Fiber Media Converter SC/ST 2km
MCM110SC2 / MCM110SC2GB / MCM110SC2EU
MCM110ST2 / MCM110ST2GB / MCM110ST2EU
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
Packaging Contents
• Fiber/Ethernet media converter
• Power Adapter
• Instruction Manual
System Requirements
• 10/100Base-TX compatible Ethernet network
• 100Base-FX ber network
• SC/ST multi-mode ber cable
• Available AC electrical outlet
RJ45 Ethernet
DIP Switches
DIP Switches
Connector
LED Indicators
*actual product may vary from photos
RJ45 Ethernet
Connector SC Fiber
LED Indicators
ST Fiber
Connectors
Connectors
Installation
1. Connect the Ethernet cable to the Fiber Media Converter “LAN” port.
2. Connect the other end of the Ethernet cable to the router/switch/
computer NIC.
3. Connect the ber cable into the ber receptacle on the media converter.
4. Plug the provided power adapter into the media converter, and
into an available AC power outlet.
5. Connect the other end of the ber cable into the router/switch/
computer NIC/another media converter. Remember to reverse
the TX and RX leads between the two devices.
DIP Switch Settings
Switch Function State Status
SW1 UTP Mode
SW2* UTP Speed
SW3* UTP Duplex
SW4
*not enabled when SW1 set to ‘Auto’
Link Fault Pass-
through
Auto Auto UTP detection
Manual Use manual UTP settings
100 100Mbps link speed
10 10Mbps link speed
Full Full duplex
Half Half duplex
LFP LFP mode o
ON LFP mode on
LED Indicators
LED Function State Status
PWR
FX Link/Act
FEF Far End Fault
100 Mode
Full Duplex Mode
TX Link/Act
Power
Indicator
Fiber Link/
Activity
Ethernet Link/
Activity
ON Converter has power
OFF
ON Fiber link OK
OFF No link detected
Flashing Receiving data
ON Far end link failure
OFF No failure detected
ON 100Mbps
OFF 10Mbps
ON Full duplex mode
OFF Half duplex mode
ON
OFF No link detected
Flashing Receiving data
Converter has no
power
Ethernet link
detected
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 08/14/2012
Specications
MCM110SC2 MCM110ST2
1 x RJ45 Ethernet
Connectors
2 x SC Fiber
1 x Power
connector
LEDs
Power, Fiber Link/Activity, Ethernet Link/
Activity, 10/100, Full/Half Duplex, FEF
Fiber Type Multi-Mode (62.5 or 50/125 micron)
Optical Wavelength 1310nm
Maximum Distance 2 km
Transmission
Standards
Duplex Modes
Power Adapter
IEEE802.3 10BASE-T, IEEE802.3u
100BASE-TX, l00BASE-FX
Full/Half Duplex (Ethernet)
Full Duplex (Fiber)
12VDC, 200mA, center positive,
type M plug
Enclosure Material Plastic
Operating
Temperature
0°C ~ 50°C (32°F ~ 122°F)
Storage Temperature -10°C ~ 70°C (14°F ~ 158°F)
Humidity 10% ~ 90% RH
Dimensions 95.0mm x 7
Weight 90.5
1 x RJ45 Ethernet
2 x ST Fiber
1 x Power
connector
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access
our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned
for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow
the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Loading...