DVI to VGA Video Converter
DVI2VGA
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
*actual product may vary from photos
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 01/25/2012
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes only and do not represent an
endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to
which this manual applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges
that all trademarks, registered trademarks, service marks, and other protected names and/or
symbols contained in this manual and related documents are the property of their respective
holders.
Table of Contents
Introduction .......................................................................................................................................................1
Before You Begin ..............................................................................................................................................1
System Requirements ............................................................................................................................1
Contents .........................................................................................................................................................1
Installation............................................................................................................................................................2
Connecting Devices to the Scaler ..................................................................................................2
Using the Video Scaler ..................................................................................................................................3
Specications .....................................................................................................................................................5
Troubleshooting ...............................................................................................................................................6
Technical Support ...........................................................................................................................................7
Warranty Information ....................................................................................................................................7
Instruction Manual
i
Introduction
Thank you for purchasing a StarTech.com video scaler. This product allows you to convert
between DVI and VGA video formats and resolutions. The input resolution is automatically
detected while the output resolution and refresh rate can be selected through an on-screen
menu with the buttons located on the front of the panel.
Features
• Converts DVI-D video input to Analog RGBHV or YPbPr output. A DVI source can be displayed
onto a VGA or HDTV display using a VGA connector or component RCA connectors
• 48MB frame memory for frame rate conversion
• On-screen display allowing adjustments to brightness, contrast, color and
Horizontal/Vertical positioning
Before You Begin
System Requirements
• A DVI video source
• A display capable of using a RGBHV or YPbPr signal (15-pin connector)
• Cables necessary to make connections between input, scaler and VGA/HD display
Contents
• 1 x Video Converter box
• 1 x DVI Cable
• 1 x 5V DC 2Amp Power Adapter
• 1 x User Manual
Instruction Manual
1
Installation
These instructions assume that the display has at least one available input that uses either VGA
Video or YPbPr, and that all the devices have their cables attached. You may need to disconnect
an existing device from the display to make an input available and reconnect that device using
the video scaler.
Front Back
Connecting Devices to the Scaler
1. Place the scaler near the display and the devices you wish to use with the scaler.
2. Using the PC/HD Output port on the front of the scaler, onnect the input device (i.e. a DVD
player, satellite receiver) to the connector labeled DVI Input on the back of the video scaler.
3. Connect the scaler to the display device. If you require a VGA resolution output, use a 15-pin
D-Sub VGA cable to connect the VGA input on the display to the PC/HD output on the scaler.
If you require an HDTV resolution output, use a 15-pin D-sub to YPbPr/ RCA adaptor cable to
connect the PC/HDTV output to the YPbPr input of an HDTV device.
4. Connect the power adapter (provided) to the port marked DC 5V on the back of the video
scaler. Connect the opposite end to a wall outlet or other suitable power source. The light on
the back of the scaler will illuminate, once the unit is powered.
The DVI to VGA scaler is now ready to use.
Instruction Manual
2
Using the Video Scaler
Once you have connected the desired input and output devices to the video scaler, you can
proceed to test the connection to the television or other display. Turn on the display, and select
the input to which you connected the video switch. Consult the documentation for your display
if you are unsure on how to select A/V inputs. Usually, there will be a button on the display’s
remote or front panel labeled INPUT or A/V. If the display has multiple inputs, you will need to
ensure the input you have selected corresponds to the connectors on the television you used for
the scaler. Power on the devices you connected to the video scaler. Pressing the MENU button
will bring up the on-screen display controls on the screen as follows:
Using the + or - buttons, move the cursor to your desired selection, then press Menu to conrm
your selection and enter the corresponding sub-menu.
Input set up
When selected, a sub-menu for choosing either YPbPr or RGB as your input signal will appear.
Using the + or - buttons on the front of the scaler, select the signal format that matches the
format of your input. Pressing Menu will save your selection and exit this sub-menu.
Output set up
When selected, a sub-menu will appear giving you options as to the desired refresh rate and
resolution. Use the + or - buttons to choose the correct resolution/refresh rate. Pressing Menu
will save your selection and return you to the main menu.
Picture Adjust
This sub-menu allows you to adjust the contrast, brightness and color of the displayed image.
Using the + and - buttons, select the attribute you wish to change, and use the Menu button to
conrm your selection. Use the + or - buttons to increase or decrease the amount of the element
you are modifying, followed by the Menu button to save. Repeat this procedure for each element
as desired. Once you have made the necessary adjustments, use the + or - button to navigate to
the Exit, which will take you back to the main menu. NOTE: using the Reset feature will return all
adjustments back to the factory reset values.
HV Adjust
When chosen, a sub-menu will appear, allowing you to adjust the best horizontal and
vertical position of the picture, using the + or - buttons.
OSD Adjust
Allows you to adjust the horizontal and vertical position of the on-screen menu.
Instruction Manual
3
System Information
Displays the current software version as well as the input and output resolutions and the
corresponding refresh rates.
Auto Adjust
When chosen, the scaler will automatically adjust all parameters to the factory preset values.
Exit
When selected, exits the on-screen display
Instruction Manual
4
Specications
Input Resolutions:
Digital PC (RGBHV) HDTV (YCbCr, YPbPr, RGBHV)
VGA
VESA85
VGA70
SVGA
XGA
Mac
WXGA
1280A
SXGA
Output Resolutions:
Analog PC (RGBHV) HDTV (YCbCr, YPbPr, RGBHV)
VGA
VESA85
VGA70
SVGA
XGA
Mac
WXGA
1280A
SXGA
640x480@85Hz
640x400@85Hz
720x400@70Hz
800x600@60/72/75/85Hz
1024x768@60/70/75/85Hz
1152x864@70/75Hz
1280x768@60Hz
1280x960@60Hz
1280x1024@60Hz
640x480@60/72/75/85Hz
640x400@85Hz
720x400@70Hz
800x600@60/72/75/85Hz
1024x768@60/70/75/85Hz
1152x864@70/75Hz
1280x768@60Hz
1280x960@60Hz
1280x1024@60/75Hz
1080i
720p
576p
480p
576i
480i
1080i
720p
576p
480p
1920x1080@60Hz
1280x720@60Hz
720x576@50Hz
720x480@60Hz
720x576@50Hz
720x480@60Hz
1920x1080@60Hz
1280x720@60Hz
720x576@50Hz
720x480@60Hz
Input Format: Digital RGBHV, YPbPr or YCbCr
Input Signal: Digital RGB data bitstream
Input Connector: 24-pin DVI-D connector
Output Format: Analog RGBHV, YPbPr
Output Signal: RGB: 0.7Vp-p, 75 ohm H/V: 3 to 5 Vp-p TTL
Output Connector: HD 15-pin female
Power: 5V 2A center-positive
Instruction Manual
5
Troubleshooting
If you’re having diculty using the video scaler, try the following solutions based on the nature
of the problem.
No image is being shown on the display.
1. Ensure the video scaler is plugged in and receiving power. One LED indicator on the front
panel will be lit when the switch is receiving power.
2. Try selecting another input on the display and verify which input the scaler is connected
to. Most displays will have their A/V inputs marked with a number, so ensure the input
selected on the screen matches the physical connection between the scaler and the
display.
3. Verify cable connections between the input device, video scaler and display are snug.
Video quality is poor.
1. Verify cable connections between the input device, video scaler and display are snug.
2. Using lengthy cables may cause signal degradation. Try to locate the scaler as close to the
input device and display, as possible.
3. Enter the Picture Adjust sub-menu, ensure that Contrast, Brightness and Color are set
appropriately.
Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide
industry-leading solutions. If you ever need help with your product, visit www.startech.
com/support and access our comprehensive selec tion of online tools, documentation,
and downloads.
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for
the periods noted, following the initial date of purchase. During this period, the products may
be returned for repair, or replacement with equivalent products at our discretion. The warranty
covers par ts and labor costs only. StarTech.com does not warrant its products from defects or
damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers,
directors, employees or agents) for any damages (whether direct or indirect, special, punitive,
incidental, consequential, or other wise), loss of prots, loss of business, or any pecuniary loss,
arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If
such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Instruction Manual
7
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...