Manual Revision: 11/24/2016
For the latest information, technical specications, and support for
this product, please visit www.StarTech.com.
FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com
DKWG30DPHPD
DKWG30DPHPDU
Wireless (WiGig) or USB-C Dual-Monitor Docking
Station for Laptops - Power Delivery
*actual product may vary from photos
Instruction manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Instruction manual
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.
Déclaration d’exposition à la radiation:
Cet équipement respecte les limites d’exposition aux rayonnements IC dénies pour un
environnement non contrôlé. Cet équipement doit être installé et mis en marche à une distance
minimale de 20 cm qui sépare l’élément rayonnant de votre corps.L’émetteur ne doit ni être utilisé
avec une autre antenne ou un autre émetteur ni se trouver à leur proximité.
Contains FCC ID: PD913100NG
Contains IC: 1000M-13100NG
EU - Declaration of Conformity
StarTech.com declares that the Wireless (WiGig) or USB-C Dual-Monitor Docking Station for
Laptops - Power Delivery (DKWG30DPHPD & DKWG30DPHPDU) complies with the essential
requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of
conformity is available on request.
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario N5V 5E9
Canada
Tel: 1-800-265-1844
Fax: (519) 455-9425
Instruction manual
i
Table of Contents
Introduction ............................................................................................ 1
Product diagram ........................................................................................................................................1
Package contents ...................................................................................................................................... 2
Requirements ............................................................................................................................................. 2
About the LED indicators ......................................................................3
About the buttons..................................................................................3
About USB 3.0 and USB 3.1 Gen 1 .......................................................4
About USB Power Delivery 2.0 .............................................................4
About USB-C ..........................................................................................4
About the dock’s USB-C port ................................................................ 4
Attach the dock to the stand ................................................................5
Install the dock through WiGig (wireless) ..........................................5
Power the dock .......................................................................................................................................... 5
Connect the dock ...................................................................................................................................... 5
Run the Intel® Wireless Dock Manager software ........................................................................... 6
Install the drivers and connect your peripherals ........................................................................... 6
Install the dock through USB-C (wired) .............................................. 7
Connect the dock ...................................................................................................................................... 7
Install the drivers ....................................................................................................................................... 7
Charge a device ......................................................................................7
Congure a display device ....................................................................8
Instruction manual
ii
Supported video resolutions ...............................................................8
Technical support ................................................................................... 9
Warranty information ............................................................................9
Instruction manual
1
Introduction
This laptop docking station lets you create a full-sized workstation using either wireless
(WiGig®) docking technology or the included USB-C™ cable. When connected through
USB Type-C™ (5Gbps) you can easily power and charge your laptop directly through its
USB-C port or Thunderbolt™ 3 port.
Product diagram
Front view
Rear view
Power button
USB 3.0 fast-charge
and sync port
Recovery button
Gigabit RJ45 port
3.5 mm headset port
(4 position)
HDMI port (video 2)
DC power input port
Power LED
Status LED
Connect and
disconnect
button
Stand
USB 3.0 port
USB 2.0 ports
DisplayPort port
(video 1)
USB-C host port
Instruction manual
2
Package contents
• 1 x laptop dock
• 1 x stand
• 1 x USB-C cable
• 1 x universal power adapter
• 2 x power cords (NA/JP, ANZ for DKWG30DPHPD) (EU, UK for DKWG30DPHPDU)
• 1 x instruction manual
Requirements
• An available AC electrical outlet
• HDMI® and DisplayPort equipped display(s) with cable(s) as needed (for additional
external display)
• A 4K-capable display is required to achieve 3840 x 2160p resolution (4K is also
known as 4K x 2K)
• A DisplayPort 1.2 (or better) equipped video card is required to support 4K
resolution
• Windows® 10
Requirements to connect through WiGig
• A WiGig (IEEE 802.11ad) equipped host laptop
Requirements to connect through USB-C
• A USB-C equipped host laptop (the host USB-C port must support USB Power
Delivery 2.0 in order to power and charge your laptop, it must also support DP alt
mode to enable video output)
Notes
• The dock can connect to a host laptop’s USB-C port even if it doesn’t support USB
Power Delivery 2.0 and DP alt mode. However, without support for these two
protocols, the dock will not pass power through to your host laptop or support
video output.
• Video output capabilities are dependent on the video card and hardware
specications of the host laptop it’s connected to. Certain video cards have limited
video support, and some monitors will also limit the available resolution.
• The dock’s DisplayPort port only supports active DisplayPort video adapters.
Requirements are subject to change. For the latest requirements, please visit www.
StarTech.com/DKWG30DPHPD or www.StarTech.com/DKWG30DPHPDU.
Instruction manual
3
About the LED indicators
LED Behavior
Power Blue: The dock is powered and turned on
Not illuminated: The dock isn’t powered and is turned o
Status Amber: A WiGig connection is being set up
Green: A device is connected (your host laptop)
O: No device is connected
Blinking green: The rmware is being updated
About the buttons
Button Action
Power Press to power the dock on or o
Connect
Short press (less than two seconds):
• Connects to the host laptop during the initial setup
• Wakes up the dock and laptop when in sleep mode
(the dock goes to sleep when the laptop does)
• Puts the laptop to sleep when connected
Long press (more than two seconds):
• Disconnects the dock from the host laptop
Recovery
Press and hold for ten seconds:
• Restores the dock to the default settings
Press during power up:
• Restores the rmware to the default original
version
Instruction Manual
4
About USB 3.0 and USB 3.1 Gen 1
USB 3.0 is also known as USB 3.1 Gen 1. This connectivity standard oers speeds up
to 5Gbps. Any mention of USB 3.0 in this manual or on the StarTech.com website for
DKWG30DPHPD or DKWG30DPHPDU refers to the 5Gbps USB 3.1 Gen 1 standard.
About USB Power Delivery 2.0
USB Power Delivery 2.0 is a specication that allows power (up to 100 watts) to be sent
over a USB-C or Thunderbolt 3 cable that supports the specication.
The dock supports USB Power Delivery 2.0, delivering up to 60 watts of power through
the USB-C or Thunderbolt 3 port on your laptop.
Note: USB Power Delivery is only supported when connected to a host laptop through
USB-C. USB Power Delivery is not supported when connected through WiGig.
About USB-C
Not all USB-C ports support the full functionality of the USB Type-C standard. Some
ports might only provide data transfers, and might not support video (DP alt mode) or
USB Power Delivery 2.0.
To ensure that this dock powers and charges your laptop, check to conrm that your
host laptop supports USB Power Delivery 2.0.
To ensure this dock provides video output, check to conrm that your host laptop
supports DP alt mode. DP alt mode is a specication that allows a DisplayPort video
signal to transfer over USB-C. It enables the use of the USB-C interface for DisplayPort
signals.
Thunderbolt 3 technology also uses the USB-C connector, so you can connect the dock
to a Thunderbolt 3 port. The dock will connect to the Thunderbolt 3 port at the USB
speed of 5Gbps.
About the dock’s USB-C port
The dock features a rear-panel USB-C port. This port can only be used for connecting
to your host laptop. The port supports data throughput (up to 5Gbps), DP alt mode
(video over USB-C), and USB Power Delivery 2.0 (maximum 60 watts).
When connected through WiGig, this port cannot be used for data, power, charging, or
video throughput.
Note: Do not connect anything to the USB-C port while in WiGig mode.
Instruction manual
5
Attach the dock to the stand
To attach the dock to the provided stand, do the following:
1. Place the stand ush on a desk so that the rubber feet on the bottom of the stand
are resting on the desk’s surface.
2. Place the bottom of the dock into the stand’s opening and gently push downward
until you feel resistance and the dock will no longer move down any further.
Note: It is highly recommended that the dock be attached to the provided stand to
ensure optimal WiGig signal transmissions.
Install the dock through WiGig (wireless)
If you have a WiGig equipped host laptop with a supported WiGig card, you can
wirelessly connect the dock to your laptop.
When coupled with a WiGig equipped laptop, this dock can wirelessly connect to your
host laptop, eliminating the need for a traditional host connection cable such as a USB
3.0 or a USB-C cable.
The WiGig signal range is typically about two to four feet, which allows you to deploy
the dock at your desk, near your host laptop. After the initial pairing, you can dock and
undock as needed, by simply travelling in and out of the dock’s wireless range.
Notes:
• When connected to your host laptop through WiGig the dock only supports
2-channel audio (5 and 7-channel audio is not supported).
• HDCP content is not supported when connected in WiGig mode.
Power the dock
1. Select the appropriate power cord for your region and connect it to the power
adapter.
2. Connect the power adapter to an AC electrical outlet and to the dock’s DC power
input port.
3. Press the dock’s Power button.
Connect the dock
Connect your external display(s) to the dock’s video port(s) (for example, one
DisplayPort display and one HDMI display). On one of the displays, a dock ID will be
shown (for example, Dock_1449). If both displays are connected, a dock ID will be
Instruction manual
6
shown on each display.
Note: The indicated ID for the dock is unique and will vary from dock to dock.
Run the Intel® Wireless Dock Manager software
To connect the dock to your laptop wirelessly, you need to use Intel Wireless Dock
Manager software. The software should be pre-installed on any WiGig equipped
laptop. The software must be intially run on each laptop you want to connect the dock
to.
1. If you do not have Intel Wireless Dock Manager software, download, install, and
run the latest version from Intel, or contact your laptop manufacturer.
Note: Ensure the version you are running is 2.6.1.102 or higher. If you have the
software installed but are unsure of which version you are running click the About
icon (question mark) within the software. You can also click the Settings icon (gear) to
be given an option to check for updates at Intel.com.
2. Run the Intel Wireless Dock Manager software. If you receive a notication that says:
“Your PC is not currently connected to a dock. To connect to a dock, click here and
select the dock you want”, click the word “here”. Otherwise, proceed to step three.
3. Click on your dock ID to connect the dock to your laptop.
4. Push the Connect button on the dock to continue the installation and to wirelessly
connect the dock to your laptop. Once connected the software will display a
message that says “Successfully Connected to Dock_****.”
Notes
• If you receive a pop-up notication that says “Connection is weak” move the dock
closer to the laptop.
• For dual-display congurations, see the “Congure a display device” section.
Install the drivers and connect your peripherals
The required drivers will install automatically when the dock is powered and wirelessly
connected to your host laptop.
• Connect your peripherals to the dock (for example, USB devices, RJ 45 network).
• Do not connect anything to the USB-C port while in WiGig mode.
Instruction manual
7
Install the dock through USB-C (wired)
If you have a USB-C equipped host laptop that supports USB Power Delivery 2.0 and
DP alt mode, you can connect the dock to your laptop using the provided USB-C cable.
Note: The dock can connect to a host laptop’s USB-C port even if it doesn’t support
USB Power Delivery 2.0 and DP alt mode. However, without support for these two
protocols, the dock will not pass power through to your host laptop or support video
output.
Power the dock
1. Connect the appropriate power cord for your region to the power adapter.
2. Connect the power adapter to an AC electrical outlet and to the dock’s DC power
input port, then press the dock’s Power button.
Connect the dock
1. Connect your external display(s) to the dock’s video port(s) (for example, one
DisplayPort display and one HDMI display).
2. Connect your peripherals to the dock (for example, USB devices, RJ 45 network).
3. Connect the provided USB-C cable to a USB-C port on your host laptop and to the
dock’s USB-C port.
Notes:
• For dual-display requirements, see the “Congure a display device” section.
• Do not connect anything to the USB-C port while in WiGig mode.
Install the drivers
The required drivers will install automatically when the dock is powered and
connected to your host laptop.
Charge a device
You can use the dock’s front and rear USB 3.0 ports to charge a mobile device, even
when the dock isn’t connected to your host laptop. The dock’s USB 2.0 ports will not
charge mobile devices without a connection to a host laptop.
The dock’s front USB 3.0 port is a fast-charge and sync port that is compliant with USB
Battery Charging Speciciation Revision 1.2.
• To fast-charge a device, connect it to the front USB 3.0 port.
Instruction manual
8
Note: This front USB 3.0 port can only fast charge connected devices that comply with
USB Battery Charging Specication Revision 1.2.
Congure a display device
Use your Windows operating system to adjust display settings for multiple monitors.
Your laptop hardware must support dual external displays.
• You can set up dual monitors by using the video output ports (1x DisplayPort and
1x HDMI).
Supported video resolutions
The dock supports the following maximum resolutions.
WiGig host - maximum resolutions
Video output
conguration
Max DisplayPort
Resolution
Max HDMI Resolution
DisplayPort and HDMI
(two monitors)
1920x1200p (60Hz) 1920x1200p (60Hz)
DisplayPort (one monitor) 2560x1600p (60Hz) N/A
HDMI (one monitor) N/A 2560x1440p (60Hz)
USB-C host - maximum resolutions
DisplayPort and HDMI
(two monitors)
1920x1200p (60Hz) 1920x1200p (60Hz)
DisplayPort (one monitor) 3840x2160p (30Hz) N/A
HDMI (one monitor) N/A 3840x2160p (30Hz)
Notes
• Depending on the conguration and the supported resolution of your connected
monitor(s), the dock can support video resolutions lower than specied above.
• In a multi-display conguration, set the refresh rates on each of your connected
monitors to the same values, otherwise your monitors might not display properly.
• Video output capabilities are dependent on the video card and hardware
specications of your connected host laptop.
Instruction manual
9
Technical support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Warranty information
This product is backed by a three-year warranty.
StarTech.com warrants its products against defects in materials and workmanship
for the periods noted, following the initial date of purchase. During this period,
the products may be returned for repair, or replacement with equivalent
products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...