StarTech.com BOX4MODULE, BEZ4MOD Quick Start Manual
Docking Station Module BOX4MODULE | BEZ4MOD
Quick-Start Guide
SKU #: MOD4DOCKACPD
Product Design
Actual product may vary from photos
Front View
LED
Indicator
Power
Button
USB-A
Port
Rear View
Speaker Out
Port
DC
20V 6A
Port
USB-B
Port
Mic In
Port
HDMI
IN
Port
HDMI
In Port
USB-C
Port
HDMI
OUT
Port
Requirements
For the latest requirements and full product manual, please visit
www.startech.com/MOD4DOCKACPD.
Installation
Note: StarTech.com is not responsible for any damages related to
the installation of this product.
See the Installation section in the Modular Table Box
(BOX4MODULE) or Single Module Table Box (BEZ4MOD) User
Manual for instructions on how to install a module into a table
surface.
Mounting Installation
Installation Requirements:
• Mounting Bracket x 1
• Bracket Screws (M5 x 20 mm) x 4
• Module Screws (#6-32 x 3/16) x 8
• Writing Utensil x 1
• Phillips Head Screwdriver x 1
Note: Before mounting the Module, consider the desired position
of the ports (top and bottom) as it will aect the mounting
orientation.
1. Align the Mounting Bracket with four of the Mounting Holes
on the Module.
Note: The Module has four Mounting Holes on each side on the
Module, which gives you two dierent mounting options.
2. Insert the Bracket Screws (x4) through the Mounting Bracket
and into the Mounting Holes.
3. Tighten the Mounting Screws using a Phillips Head
Screwdriver, be careful not to overtighten.
4. Before installing the Mounting Bracket, measure and position
the Mounting Bracket in the desired location. The Module can
be mounted on a vertical or horizontal surface.
RJ45
Port
USB-A
Ports
Package Contents
• Docking Station Module x 1
• Universal Power Adapter x 1
• Power Cords (NA / UK / EU) x 3
• USB-A to USB-B Cable x 1
• USB-C Cable x 1
• Mounting Bracket x 1
• Bracket Screws (M5 x 20 mm) x 4
• Module Screws (#6-32 x 3/16) x 8
• Quick-Start Guide x 1
For the latest information, specications, and support visit www.startech.com/MOD4DOCKACPD
Note: Depending on the surface you are using to install the
product, you may need to drill pilot holes prior to installing the
screws into the surface.
5. Mark the location of the Mounting Holes using a Writing
Utensil. These marks can be used as a guide to indicate where
the Mounting Screws will be installed in the surface.
6. Install the Bracket Screws (x4) through the Mounting
Bracket and into the mounting surface, using a Phillips Head
Screwdriver. Be careful not to overtighten.
Warning: To prevent the Mounting Screws from penetrating
the opposite side of the installation surface, be conscious of
the size of the Mounting Screw compared to the depth of the
surface.
Manual Revision: 11/09/2018
Quick-Start Guide
SKU #: MOD4DOCKACPD
Powering the Module
1. On the bottom of the Docking Station Module, connect the
Universal Power Adapter to the DC 20V 6A Port.
2. Tighten the Lock Screw on the Universal Power Adapter, to
ensure connectivity.
3. Connect the other end of the Universal Power Adapter into an
appropriate power source.
Note: By default the Power Button on the Docking Station
Module is set to On. If the LED Indicator on the Docking
Station Module does not light up when connected to the
Universal Power Adapter and power is present, press the
Power Button to turn on the Docking Station Module. The
LED Indicator will light up white.
Connecting Devices to the Module
For instructions on how to connect devices to the Module see
Connecting Devices to the Top of the Module and/or Connecting
Devices to the Bottom of the Module sections in the Module’s
User Manual (found at www.startech.com/MOD4DOCKACPD).
LED Indicators
Power
Solid LED (White)
• Indicates that the Docking Station Module is active (the
Universal Power Adapter is correctly connected to an AC
Electrical Outlet).
LED O
• Indicates that the Power Button is turned o, the Universal
Power Adapter is not correctly connected to an AC Electrical
Outlet or the Docking Station Module is not receiving power
from the AC Electrical Outlet.
RJ45 Port
Amber LED
• Solid LED
• Indicates that link speed is either 1000Mbps (1 GbE), 100Mbps,
or 10Mbps
• LED O
• Indicates no connectivity
Green LED
• Flashing LED
• Indicates that a link is established
• LED O
• Indicates that no link is established
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
• Wiring terminations should not be made with the product and/or electric lines under power.
• Product installation and/or mounting should be completed by a certied professional as per
the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed to avoid creating
electric, tripping or safety hazards.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous
tension.
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit et/ou les câbles
électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un professionnel certié et
dans le respect des normes locales et du code de construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent être placés et
acheminés de façon à éviter tout risque électrique, de chute ou de sécurité
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
• 電源が入っている状態の製品または電線の終端処理を行わないでください。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回しを行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよ
うにしてください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le linee elettriche
sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un tecnico
professionale certicato che conosca le linee guida locali sulle norme edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati e stesi in modo da
evitare pericoli di inciampo, rischi di scosse elettriche o pericoli per la sicurezza.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
• Montering av kabelavslutningar får inte göras när produkten och/eller elledningarna är
strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner och enligt
gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så sätt att risk för
snubblingsolyckor och andra olyckor kan undvikas.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and
on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help
To view manuals, FAQs, videos, drivers, downloads, technical drawing, and more, visit www.startech.com/support.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or
modications not expressly approved by StarTech.com could void the user’s authority to operate
the equipment.
For the State of California
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes only and do not represent an
endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of their
respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide
industry-leading solutions. If you ever need help with your product, visit www.startech.com/
support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a one-year warranty. StarTech.com warrants its products against defects
in materials and workmanship for the periods noted, following the initial date of purchase. During
this period, the products may be returned for repair, or replacement with equivalent products at
our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its
products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers,
directors, employees or agents) for any damages (whether direct or indirect, special, punitive,
incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss,
arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If
such laws apply, the limitations or exclusions contained in this statement may not apply to you.
StarTech.com Ltd.
45 Artisans Cres.
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
2500 Creekside Pkwy.
Lockbourne, Ohio
43137
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd., Brackmills
Northampton
NN4 7BW
United Kingdom
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
IT: it.startech.com
JP: jp.startech.com
NL: nl.startech.com
Loading...