Silent ATX PC Case
ATXSILENT
Instruction Guide
The Professionals’ Source For Hard-to-Find Computer Parts
SSIILLEENNTT AATTXX CCAASSEE
* Actual product may vary from photo
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
1
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing Your Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Using Your Front Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2
Introduction
Thank you for purchasing a StarTech.com silent ATX computer case. The walls in the
case are covered with noise-absorbing pads and coated with silicon to reduce noise and
vibration. With ten drive bays, seven expansion slots, tool-less entry, a clamshell full of
helpful accessories and room for a full-sized dual-processor ATX motherboard, you’ll be
able to build the custom computer of your dreams quickly and easily. The case also
features front-mounted USB 2.0, audio, and IDE ports for your convenience.
Features
•Noise-absorbing pads and silicon coating help eliminate noise and vibration
• Clam-shell full of screws, anti-vibration pads, and accessories make installation and
customization easy
• USB 2.0, audio, and IDE ports are located in the front with a pop-out door for
easy access
• Comes with 10 drive bays and 7 expansion slots
• Spacious interior provides plenty of room for a full-size dual-processor ATX
motherboard and ATX power supply
• Backed by StarTech.com’s three-year warranty
Before You Begin
To ensure a quick and easy case assembly, please read through the following instructions
before assembling your case.
WARNING: Do not attempt to install any computer components with the system
plugged in. Never open your computer case when your system is turned on. Always
make sure that the computer is off and unplugged before attempting to assemble or
alter your computer. Computer equipment can also be severely damaged by static
electricity. Be sure that you are properly grounded before opening your computer case or
touching any components. StarTech.com recommends that you wear an anti-static strap
when installing any computer equipment. If an anti-static strap is unavailable, discharge
yourself of any static electricity build-up by touching a large grounded metal surface
(such as the computer case) for several seconds. Also be careful to handle cards and
motherboards by their edges and not the gold connectors.
Contents
•1 x ATXSILENT case
•1 x clamshell with assorted screws, anti-vibration pads, and accessories
3
System Requirements
This case does NOT come with a motherboard, power supply, hard or floppy disk
drives, sound cards, I/O cards or any other computer component not listed above. You
will need to supply these components yourself.
NOTE: When purchasing a motherboard for this case, make sure that the motherboard
uses the same external/internal connections as the ATXSILENT. If your motherboard
does not match the case, you may not be able to use some of the front ports.
Installing Your Components
Install your internal components according to their manufacturer’s instructions. The
ATXSILENT can support full-sized dual-processor ATX motherboards and ATX power
supplies. The following are installation hints and suggestions that you might find useful.
Motherboards: The clamshell contains motherboard standoffs, screws, and buffers (red
circles). Be sure to place the buffers between the motherboard and the screws. Remember
to follow the manufacturer’s instructions and ensure that all your components are
properly connected.
Power Supplies: The ATXSILENT supports ATX power supplies. To complement the
ATXSILENT, StarTech.com recommends using a silent power supply, like the
StarTech.com ATXPOW350SL. To further dampen the noise of your power supply, you
can use some of the pads in the clamshell.
Peel the paper off the back of the power supply anti-vibration pad and stick the pad to
your power supply. Make sure you stick the pad to the side of the power supply that will
be facing the rear of the case. You can also stick the two rectangular anti-vibration pads
on the underside of the power supply to prevent vibration against the “lip” of the case.
The pads will act as a buffer between the power supply and the case, preventing
vibration.
Place the pad
on your power
supply, making
sure that the
fan is not
blocked.
4
Fans: As with power supplies, StarTech.com recommends using silent case fans (like the
StarTech.com FAN8X25TX3L) to maximize the effectiveness of your silent case. To further
dampen the noise and vibration from your fans, you can use the triangular fan antivibration pads in the clamshell.
Peel the paper off the back of the fan anti-vibration pad. Place one anti-vibration pad on
each corner of the fan, making sure that you have placed the pads on the side of the fan
that will be in contact with the wall of the case. The pads will act as a buffer between the
fan and the case to prevent vibration.
When installing rear fans, you can use the round black rubber rings to prevent vibration.
Place a rubber ring on the outside of your case so that the ring is between the head of the
screw and the case.
Disk Drives: The hard drive cage is removable with a thumbscrew. You may find it
easier to remove the drive cage before installing your hard drives. The screws in the
clamshell are color-coded to help make drive installation easier. Make sure you follow
manufacturer’s instructions when installing and connecting your disk drives.
Other Accessories: Also in the clamshell are optional accessories that can help you
organize the inside of your case. You can remove the sticker from the cable holder, secure
it to your case, and run your cables through it to keep them organized. You can also use
the cable ties to group cables to keep them organized and neat.
Stick a triangular
pad on each corner
of your fan
5
Using Your Front Ports
First, make sure that the cables from your front USB 2.0 and audio ports are connected to
your motherboard. Make sure that the IDE cable from the front IDE port is connected to
an IDE port on your motherboard. If your cables are not connected properly, your front
ports will not work. Check with your motherboard manufacturer for specifics on
connecting your front ports.
To open the front port panel, push on the door gently, then release. You can plug your
USB 2.0 or audio devices into the front ports and use them as normal.
Using the Front IDE Port
You can use the front IDE port to connect your IDE hard drives for making backups or
for testing. Use the provided IDE cable and power adapter to connect your hard drive to
the front IDE port.
6
Technical Specifications
Drive Bays 4 x external 5.25”
2 x external 3.5”
4 x internal 3.5”
Expansion slots 7 slots
Cooling 1 x 8cm fan
Enclosure 1mm steel
Motherboards Dual processor ATX including P4
Front I/O Ports 2 x USB 2.0 (Type A)
1 x Speaker
1 x Microphone
1 x IDE (40-pin)
1 x Power connector (4-pin)
Dimensions 8 x 20 x 18.25"
W x D x H (203 x 508 x 464 mm)
Weight 24.3lbs
(11 kgs)
7
Technical Support
The following technical resources are available for this StarTech.com product:
On-line help:
We are constantly adding new information to the Tech Support section of our web site. To
access this page, click the Tech Support link on our homepage, www.startech.com. In the
tech support section there are a number of options that can provide assistance with this
card.
Knowledge Base - This tool allows you to search for answers to common issues using
key words that describe the product and your issue.
FAQ - This tool provides quick answers to the top questions asked by our customers.
Downloads - This selection takes you to our driver download page where you can
find the latest drivers for this product.
Call StarTech.com tech support for help:
USA/Canada: 1-519-455-4931
UK/Ireland/Europe: 00-800-7827-8324
Support hours: Monday to Friday 9:00AM to 5:00PM EST (except holidays)
Warranty Information
This product is backed by a three-year warranty. In addition, StarTech.com warrants its
products against defects in materials and workmanship for the periods noted below,
following the initial date of purchase. During this period, the products may be
returned for repair, or replacement with equivalent products at our discretion. The
warranty covers parts and labor costs only. StarTech.com does not warrant its products
from defects or damages arising from misuse, abuse, alteration, or normal wear and
tear.
Limitation of Liability
In no event shall the liability to StarTech.com Ltd. (or its officers, directors, employees or
agents) for any damages (whether direct or indirect, special, punitive incidental,
consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss,
arising out of related to the use of the product exceed the actual price paid for
the product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement
may not apply to you.
Revised: July 17, 2003
Loading...