Manual Revision: 01/25/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
ATX2POW400HS
ATX2POW450HS
ATX2POW500HS
ATX2POW550HS
400 Watt Silent ATX12V PC Computer
Power Supply w/ 120mm Fan
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements .............................................................................................................................. 1
Installation ..............................................................................................2
Software Installation ................................................................................................................................ 3
Conguration Diagram ........................................................................................................................... 4
Operation ................................................................................................5
Front Panel Pushbuttons ........................................................................................................................ 5
Keyboard Hotkeys ..................................................................................................................................... 5
KVM Switcher Software ........................................................................................................................... 6
Specications ..........................................................................................9
Technical Support ..................................................................................10
Warranty Information ............................................................................10
Instruction Manual
1
Introduction
Thank you for your purchase of a StarTech.com ATX 12V Silent Power Supply. Designed
to deliver more power for high-end and dual core systems, this Power Supply oers a
generous number of power connections, including PCI Express and SATA, for maximum
compatibility. A 12cm fan oers quiet operation and superior performance, designed
for extra-long life in personal and industrial computers.
Packaging Contents
• 1 x Power supply
• 1 x Standard power cable
• 1 x Instruction manual
Instruction Manual
2
Installation
CAUTION: Computers contain sensitive electronic components that are easily
damaged by static electricity and excessive shock. When handling the power supply
and other components, ensure you are properly grounded using an anti-static mat or
similar device. If anti-static equipment is not available, ground yourself by touching
the exterior of the computer case or another large metal surface before handling any
peripherals.
1. Installation of a power supply requires some mechanical skill and requires that you
open your computer case to disconnect and reconnect wires. If you are unfamiliar
with this kind of work, consider bringing your computer and new StarTech.com
power supply to your local computer store for help.
2. Check the red switch on the rear of the power supply, next to the power cord plug.
Be sure it is set to the correct voltage for your country. In North America, it should
read "115". In Europe and Australia it should read "230". To change the switch, use
a screwdriver in the notch of the switch and slide it to the opposite side. If you are
unsure of the voltage used in your country, contact your electricity provider before
proceeding.
3. If you are replacing an old power supply in your computer, ensure the computer is
shut down and disconnect the power cord from the back of the old supply.
4. Open your computer case. In most designs, the case is opened by removing two or
three screws at the rear of the case and then sliding the covering panel backward
until it comes free. If your case is a tower style, ensure that you remove the panel
that will expose the top of the computer's motherboard. This is generally the leftside panel. There are many dierent case designs, however, so if you are unsure of
how to open your particular case, consult the user manual for your case or contact
your local computer store for help.
5. With the computer case open, review the connectors being used from your old
power supply. If you are building a new computer, review the connectors that you
will need to use. Check the type of connector on your motherboard and use either
the 24 or 20 pin ATX power connector on the power supply as appropriate.
6. Disconnect the old power supply connections from inside your computer. Hard
disk drive, CD drive and oppy disk drive connectors disconnect by pulling on the
connector. The motherboard connector(s) have a clip that must be pressed while
pulling on the connector to release them. A rocking motion while pulling will aid in
Instruction Manual
3
getting the connectors loose. Never pull on the wires of a connector to unplug it.
7. Check that all the wires from your old power supply are free. Remove the four
screws on the rear of your old power supply to free it from the computer case.
Support the power supply with one hand if it could fall while removing the last
screw. (Such as in a tower style case.) Remove the power supply by sliding it back
and then out through the side of your case.
8. Install your new power supply by positioning it through the side or top of your case
(depending on your case style) and then back onto the power supply mounts. Check
that the orientation with the screw holes in your case is correct; all four holes must
be aligned. Support the power supply with one hand while threading a mounting
screw through the back of the case and into the power supply. The screw should
thread smoothly and should not require eort. Do not force it or you could damage
the mounting holes. If the screw won’t thread smoothly, remove it and check to
ensure the mounting holes are correctly lined up. Repeat for the remaining three
screws. Do not fully tighten any of the screws until they all have been threaded into
their mounting holes. (Note: Consider Startech part SCREWTHUMB screws for easier
installation.)
9. Tie unused wires away from fans and other moving parts.
10. Replace the case cover and secure it.You may wish to not replace the screws until
after you have checked that all connections are working.
11. Toggle the rear power switch on power supply to o. (The “0” symbol on the
switch.) Connect the power cord to the power supply and plug it in to a grounded
power outlet. (The power supply MUST be connected to a grounded outlet.) Toggle
the rear power switch to on.
12. Start your computer.You should hear its fans and devices immediately begin to
run. If you do not, toggle the rear switch on the power supply to o, disconnect the
power cord, open the case and check that all connectors are well seated and secure.
13. When you have conrmed all connections are working, replace the screws in
your case.
14. Power supplies contain electrical and electronic components and should be
disposed of properly. If you are replacing a power supply, please follow your city’s
rules for proper disposal of electrical equipment.
Instruction Manual
4
Instruction Manual
5
Specications
Number of Ports 2
Console Connectors 1 x DVI-I
2 x USB type A
1 x 3.5mm mic jack
1 x 3.5mm speaker jack
Computer Connectors
(all ports)
2 x DVI-I
2 x USB type B
Video Resolution 1920x1200 (digital)
2048x1536 (analog)
Power 5VDC, 2A
Dimensions 154.0mm (6.06”) x 65.5mm (2.58”) x
27.0mm (1.06”)
Certications ROHS, CE, WEEE, FCC
Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...