StarTech.com 25SAT22MSAT User Manual

Dual mSATA SSD to 2.5in SATA SSD Converter with RAID
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 10/28/2014
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Instruction Manual
Table of Contents
Product Diagram ....................................................................................1
Front View ....................................................................................................................................................1
Back View ..................................................................................................................................................... 2
Introduction ............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements .............................................................................................................................. 2
mSATA SSD Installation .........................................................................3
Congure RAID .......................................................................................5
RAID Lock/Unlock Jumper Pins ............................................................................................................ 5
RAID Mode Setting Jumper Pins .......................................................................................................... 5
Set RAID Conguration ........................................................................................................................... 6
Hard Drive Initialization ........................................................................6
LED Activity and Drive Failure Indicators ...........................................8
Technical Support .................................................................................. 9
Warranty Information ............................................................................9
Instruction Manual
i
Product Diagram
Front View
1. RAID lock/unlock jumper pins
2. Drive Activity/Fail LEDs
3. Drive #1 mSATA connector
4. Drive #2 mSATA connector
5. Drive #1 mounting bracket
6. Drive #2 mounting bracket
7. Top mounting holes
Instruction Manual
1
Back View
1. DATA & Power Combo (7+15 pin)
2. RAID setting jumper pins
3. Side mounting holes
Introduction
Packaging Contents
• 1 x Dual mSATA to 2.5in SATA Adapter
• 1 x Mounting screw kit
• 1 x Installation Manual
System Requirements
• 2 x mSATA Drives
• SATA Host Device
Instruction Manual
2
mSATA SSD Installation
WARNING! SSD Drives and storage adapters require careful handling. If you are not careful with your SSD Drive, lost data may result. Always handle your drive with caution. Be sure that you are properly grounded by wearing an anti-static strap when handling computer components or discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds.
1. Slide the mSATA connector on one of your SSDs into the Drive #1 mSATA receprical connector on the 25SAT22MSAT.
2. Press the drive down toward the Drive #1 mounting bracket, until the drive clicks into place.
Instruction Manual
3
3. Slide the mSATA connector on your other SSD into the Drive #2 mSATA receprical connector on the 25SAT22MSAT.
4. Press the drive down toward the Drive #2 mounting bracket, until the drive clicks into place.
5. The SSDs have now been installed.
Note: To remove drives #1 and #2, pull upward on two the tabs located on the top of either drive, then slide the drives out one at a time.
Instruction Manual
4
Congure RAID
WARNING! Setting or changing your RAID modes will erase the data or metadata on your existing SSD drives.
RAID Lock/Unlock Jumper Pins
The RAID lock/unlock jumper pins, located above the drive mounting brackets enable you to lock your RAID conguration so it cannot be changed. Or unlock your conguration so it can be changed.
G
S
N
N
E
.
D
T
C
Use the included jumper and the table below, to short the pins and set the mode for your desired conguration.
Mode Description Jumper Pins
Unlocked
Locked
Enables you to change your RAID
conguration mode.
Does not allow you to change your RAID
conguration mode.
SET-GND
N.C-SET
Instruction Manual
5
RAID Mode Setting Jumper Pins
The RAID setting jumper pins, located next to the SATA connector enable you to set your desired RAID conguration between RAID 0, RAID 1, JBOD, and RAID initial Mode.
RAID Setting Jumper Pins
4 5 6
1 2 3
Use the included jumpers and the table below, to short the pins and set your desired RAID mode.
RAID Mode Description Short Pins
RAID 0 Striping - Improves system performance 1-2, 4-5
RAID 1
BIG
JBOD
Mirror – Creates a redundant drive on the
second drive for security
Spanning – Creates a large single drive
volume consisting of both drives.
Just a Bunch of Disks – Allows access to both
drives individually
(Note: A port multiplier compatible SATA
controller is required for this mode)
SATA Connector
2-3, 4-5
1-2, 5-6
2-3, 5-6
Set RAID Conguration
Note: Your RAID conguration must be set to JBOD before the device can be recongured to RAID 0, RAID 1, or BIG. If you have set a dierent RAID conguration and now wish to recongure your RAID, please set the device back to JBOD before changing the conguration again.
1. Set the RAID Lock/Unlock Jumper Pins to the unlock position.
Instruction Manual
6
2. Using the RAID Mode setting jumper pins to your desired Mode.
3. Connect the SSD RAID card to your SATA host device. Note: Refer to the manual for your SATA host device for installation instructions. The top or side mounting holes and included screw kit may, or may not be required to assist in your installation.
4. Power on the SATA host device.
5. Your RAID array has now been installed.
6. (Optional) If you would prefer to lock your RAID array so it cannot be altered by the RAID mode setting jumper pins, power down your SATA host device, and set the RAID Lock/Unlock Jumper Pins to the lock position.
Hard Drive Initialization
If the mSATA SSD RAID Array is new or otherwise blank, it may need to be initialized and formatted before use. Follow the steps below in a Windows interface to initialize the drive.
1. From the main Windows desktop, right-click on “My Computer” (“Computer” in Vista/ 7 / 8), then select Manage. In the new Computer Management window, select Disk Management from the left window panel.
2. A dialog window should automatically appear, asking you to initialize the drive. Depending on the version of Windows, it will give you the option of either creating an “MBR” or “GPT” disk. GPT (GUID partition) is not compatible with some older operating systems, while MBR is supported by newer and older operating systems.
3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard drive capacity to conrm it’s the correct hard drive) and then right-click in the section that says “Unallocated” and select “New Partition”.
Instruction Manual
7
4. Follow the on screen prompts to initialize the drive in the format of your choice.
LED Activity and Drive Failure Indicators
The 25SAT225MSAT includes an LED panel to visually monitor activity and failure of each drive. Please review the table below for a list of each specic indication.
Activity for
Drive #1
Activity for
Drive #2
Device Unplugged O O
Instruction Manual
Failure for
Drive #1
Description Activity LED Drive Failure LED
Device Plugged in On O
Device Accessing Flashing On O
Device Failed O On
8
Failure for
Drive #2
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Instruction Manual
9
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...