110VDSLEXT
110VDSLEXTGB
110VDSLEXTEU
Instruction Manual
VDSL Ethernet LAN Extender
10/100 VDSL Ethernet
LAN Extender Kit
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver •
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and
do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in
question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks,
service marks, and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.
Table of Contents
Installation ....................................................................... 1
Operation ......................................................................... 1
LED Displays ...........................................................................1
DIP Switch Settings .................................................................2
Connector Architecture ...............................................................5
Specifications .................................................................. 6
Technical Support ........................................................... 7
Warranty Information ...................................................... 7
i
Installation
Package Contents
1 x Extender •
1 x Receiver •
2 x RJ-45 to VDSL Cable •
1 x Instruction Manual •
2 x Power Adapter •
Hardware Installation
To install the 110VDSLEXT, all four of the DIP switches must be in 1.
the upwards (OFF) position.
Plug the DC power adapter into the port on the rear panel of the 2.
unit, and then into an available AC outlet.
Plug in an RJ45 Ethernet cable to the RJ45 port on the 110VD-3.
SLEXT.
Plug a phone cable into the VDSL port of the 110VDSLEXT. 4.
Operation
LED Displays
LAN LED Display
LED Blinking ON OFF
1
2
3
Activity Link up Link down
100 Mbps 10 Mbps
Full duplex Half duplex
1
VDSL LED Display
LED Blinking ON OFF
1
2
3
Activity
-
Slowly: Idle
Quickly: Training
Device
Power On
CPE Mode CO Mode
Linked Offline
Device Power Off
DIP Switch Settings
The 110VDSLEXT has a 4-position DIP switch for configuration of
Side, Channel, Rate Limit, and SNR.
Pin 1 - CO, CPE Switch
OFF: If Pin 1 is in the OFF position, the 110VDSLEXT will operate in
Central Office (CO) mode.
ON: If Pin 1 is in the ON position, the 110VDSLEXT will operate in
Customer Premise Equipment (CPE) mode.
Pin 2 - Interleave Noise Protection
2
OFF: If Pin 2 is in the OFF position, the 110VDSLEXT will operate in
Interleave mode, with communication protection for up to 250ms of
impulse noise with latency less than 6 ms
ON: If Pin 2 is in the ON position, the 110VDSLEXT will operate in Fast
mode, with direct data transmissions having less than 1ms of latency.
Pin 3 - Band Plan
OFF: If Pin 3 is in the OFF position, the 110VDSLEXT will operate in
Symmetric mode, with both downstream and upstream transmissions
operating on the G.997 band plan.
ON: If Pin 3 is in the ON position, the 110VDSLEXT will operate in
Asymmetric mode, with asymmetric short range transmissions operating at the highest available line rate.
3
Pin 4 - General Protection
OFF: If Pin 4 is in the OFF position, the 110VDSLEXT will operate with
a SNR ratio up to 9 dB.
4
ON: If Pin 4 is in the ON position, the 110VDSLEXT will operate with a
SNR ratio of 6 dB.
Connector Architecture
Ethernet Port
Pin Number Assignment (MDI-X)
1
2
3
4
5
6
7
8
VDSL Port
Pin Number
1
2
3
4
5
RX+; Receive data +
RX-; Receive data -
TX+; Transmit data +
Not used
Not used
TX-; Transmit Data -
Not used
Not used
Assignment (MDI-X)
Not used
Not used
Not used
ANALOG Input/Output
ANALOG Input/Output
6
7
8
Not used
Not used
Not used
5
Specications
LAN Interface
VDSL Interface
RJ-45 connector
Complies with IEEE
802.3/802.3u/802.3x
10/100 Base-T Auto-Negotiation,
Auto-MDI/MDI-X
RJ-45 connector
DMT Encoding
Complies with ITU-T
G993.1/993.2
On-board surge protection
DIP Switch
LED
Power Supply
Power Consumption
Dimensions
4 position
LAN: ACT/LNK, 10/100 Mbps,
Half/Full Duplex
VDSL: Power On/Off, CO/CPE,
Idle/Trained/Link
DC single 12 Volt over 35mm DC
jack
4.2 Watt maximum
95.5 x 69.4 x 22mm
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commit-ment to provide industry-leading solutions. If you ever need help
with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
Warranty Information
This product is backed by a one year warranty.
In addition, StarTech.com warrants its products against defects in
materials and workmanship for the periods noted, following the initial
date of purchase. During this period, the products may be returned for
repair, or replacement with equivalent products at our discretion. The
warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse,
alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com
USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss,
arising out of or related to the use of the product exceed the actual price
paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
7
StarTech.com has been making “hard-to-find easy” since 1985,
providing high quality solutions to a diverse IT and A/V customer
base that spans many channels, including government, education
and industrial facilities to name just a few. We offer an unmatched
selection of computer parts, cables, A/V products, KVM and Server Management solutions, serving a worldwide market through our
locations in the United States, Canada, the United Kingdom and
Taiwan.
Visit www.startech.com today for complete information about all
our products and to access exclusive interactive tools such as the
Cable Finder, Parts Finder and the KVM Reference Guide.
Loading...