StarTech WIFI2HDMC, WIFI2HDMCGE User Manual

Wireless Display Adapter for Mobile Devices
Actual product may vary from photos
User Manual
SKU#: WIFI2HDMC/WIFI2HDMCGE
For the latest information and specications visit
www.startech.com/WIFI2HDMC
www.startech.com/WIFI2HDMCGE
Manual Revision: 01/29/2021
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric lines under power.
• Product installation and/or mounting should be completed by a certied professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un professionnel certié et dans le respect des normes locales et du code de construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent être placés et acheminés de façon à éviter tout risque électrique, de chute ou de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでくださ い。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に 従い、有資格の専門業者が行うようにしてください。
• ケーブル(電源ケーブルと充電ケーブルを含む)は、適切な配置と引き回し を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう にしてください 。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un tecnico professionale certicato che conosca le linee guida locali sulle norme edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o pericoli per la sicurezza.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.
Warning Statements
• Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage.
• Never use this product if parts are missing or damaged.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Compliance Statements ........................................................................1
Safety Statements ..................................................................................2
Warning Statements ..............................................................................3
Product Diagram ....................................................................................7
Side View ...................................................................................................................................................... 7
Rear View ...................................................................................................................................................... 8
Product Information ..............................................................................9
Packaging Contents ................................................................................................................................. 9
System Requirements .............................................................................................................................. 9
Installation ..............................................................................................10
Installing the Display Adapter .............................................................................................................. 10
Upgrading Firmware ................................................................................................................................11
Connecting to a Smartphone or Tablet .............................................................................................13
Connecting to a Computer ................................................................................................................... 14
AllShareCast/Screen Mirror Device (Samsung) .............................................................................. 15
Android Nexus Device 4.2 or Higher .................................................................................................. 18
Conguration ..........................................................................................19
Accessing the Remote Control Interface .......................................................................................... 19
Conguring a Wired Connection ........................................................................................................21
Changing the Device Name .................................................................................................................. 22
Conguring a WiFi Connection ............................................................................................................ 24
Conguring Virtual AP ............................................................................................................................ 25
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Creating a Bridge to a Wireless Connection ....................................................................................27
Creating a Bridge to a Wired Connection .........................................................................................28
Conguring Night Mode ........................................................................................................................ 30
Setting HDMI Output Method .............................................................................................................. 31
Conguring a Surround Sound Mode ............................................................................................... 32
Conguring Lip Sync Mode ................................................................................................................... 33
Conguring Aspect Ratio ...................................................................................................................... 35
Conguring a TV System ........................................................................................................................ 36
Scaling Video Output ............................................................................................................................... 37
Conguring Video Output ..................................................................................................................... 38
Setting the On-Screen Display Language ........................................................................................ 39
Resetting the Display Adapter to Factory Settings ....................................................................... 40
Resetting the Display Adapter’s IP Address .....................................................................................41
Checking the Current Firmware Version ........................................................................................... 42
ScreenShare Mode .................................................................................44
Installation ................................................................................................................................................... 44
Logging into ScreenShare ......................................................................................................................45
Checking the MAC Address ................................................................................................................... 47
ScreenShare Panel Controls ..................................................................................................................48
Conguring a Display Mode ................................................................................................................. 49
Conguring a Display Resolution ........................................................................................................ 50
Conguring the Display’s Aspect Ratio .............................................................................................52
Enabling Auto Resolution ...................................................................................................................... 53
Enabling Auto Save .................................................................................................................................. 54
Exiting the ScreenShare App ................................................................................................................ 55
Playing Media from a USB Stick ...........................................................56
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
AirFun Utility ...........................................................................................56
Installation ................................................................................................................................................... 56
Operation ..................................................................................................................................................... 57
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
Side View
1 2
1
2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
USB Media Input
Mode Selection Button
Rear View
3
4
Analog Audio/Video Out Port
3
4
5
6
7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
5
HDMI Out Port
RJ45 Port
Power Button
Power Adapter Port
6 7
Product Information
Packaging Contents
Wireless Display Adapter x 1
Universal Power Adapter (NA/UK/EU) x 3
USB Cable to Power Adapter Port (optional for USB Power
source) x 1
4 position A/V cable x 1
User Manual x 1
System Requirements
HDMI-enabled display device w/ cabling (i.e. television,
projector)
Miracast, or 802.11n/g Wireless-enabled video source device
(i.e. Smartphone, tablet, Computer system)
USB Flash Drive (For updating the device’s rmware)
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installation
Installing the Display Adapter
1. Connect an HDMI Cable (sold separately) to the HDMI Out
Port on the Display Adapter and the other end of the HDMI Cable to the HDMI In port on a Display Device.
2. Connect the Universal Power Adapter to the Power
Adapter Port on the Display Adapter and the other end to an AC Electrical Outlet.
- or -
3. Connect the USB Power Cable (included) to the Power
Adapter Port on the Display Adapter and the other end to
an available USB Power Source.
4. Press the Power Button on the Display Adapter.
5. The Launch screen will appear on the Display Device once
the installation is complete.
Notes: The Launch screen may take several seconds to load. The appearance of the Launch screen may vary depending
on the rmware version you are using.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
10
Upgrading Firmware
For optimal performance, make sure that the Display Adapter’s rmware is up to dated.
Warnings: Do not unplug the USB ash drive or power down the device until the new primary launch screen is displayed.
Firmware upgrades are irreversible.
Identifying Firmware Version
The rmware version number will be in the bottom right-
hand corner of the Launch screen.
Updating from Version 1.6.5
1. Download the rmware update les from StarTech.com and
unzip the compressed le.
2. Copy install.img and install_sp.img from the downloaded
folder to the root directory (the parent/top directory) of the USB ash drive.
3. Ensure the Display Adapter is powered o.
4. Plug the USB ash drive into the USB Media Input on the
Display Adapter.
5. Hold down the Mode Select Button and turn on the
Display Adapter by pressing the Power Button. Continue to hold down the Mode Select Button while the device powers on.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
11
6. Release the Mode Select Button after the Please wait for
USB update appears on your Display Device.
7. The rmware on your Display Adapter will now update.
Once the update has completed the Launch screen will appear.
Update from Version 2.0.0
1. Download the rmware update les from StarTech.com and
Unzip the compressed le.
2. Copy install_sp.img from the downloaded folder to the root
directory (the parent/top directory) of the USB ash drive.
3. Once the le has been moved to your USB ash drive,
rename install_sp.img le to install.img.
4. Ensure the Display Adapter is powered o.
5. Plug the USB ash drive into the USB Media Input on the
Display Adapter.
6. Hold down the Mode Select Button and turn on the
Display Adapter by pressing the Power Button. Continue to hold down the Mode Select Button while the device powers on.
7. Release the Mode Select Button after the Please wait for
USB update appears on your Display Device.
8. The rmware on your Display Adapter will now update.
Once the update has completed the Launch screen will appear.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
12
Connecting to a Smartphone or Tablet
The Display Adapter can connect (through a wireless connection) to a Miracast enabled device (smart phone or tablet).
1. Set the Display Adapter to Miracast mode. Press the Mode
Select Button until the Miracast Launch screen is displayed.
Miracast Launch screen
2. The Miracast Launch screen will display the Adapter name
and Adapter ID.
Note: The Display Adapter name cannot be edited/ changed.
3. Connect to the Display Adapter using your Miracast-
enabled smartphone or tablet.
Note: Exact steps regarding Miracast setup will vary de­pending on your device. Please review the documentation included with your smartphone or tablet.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
13
Connecting to a Computer
The Display Adapter can connect (through a wireless connection) to a Computer with an Operating System (OS) Window 8.1 or higher.
Note: Please ensure the drivers for your graphics adapter and wireless adapter are up to date.
1. Launch the Windows 8 Charms Bar and select Devices.
2. Select Project, then Add a wireless display.
3. Select the Display Adapter from the list of devices.
4. If you are prompted for a PIN code, enter the PIN code that
pops up on the Display Adapter screen and click Next.
5. If you are prompted for a PIN code, enter the PIN code that
pops up on the Display Adapter screen and click Next.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
14
AllShareCast/Screen Mirror Device (Samsung)
1. Open the Settings menu.
2. Select More Settings.
Settings screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
15
3. Scroll through the list and select AllShare Cast or Screen
Mirror (depending on your version of Samsung device).
All Share Cast
4. Turn AllShare Cast ON and select the device name from the
list. By default Display Adapter will be listed as the device name. Tap the device to connect.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
16
AllShare Cast screen
5. The smartphone or tablet screen will now be shared on your
Display Device.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
17
Android Nexus Device 4.2 or Higher
1. Open the Settings menu.
Settings menu
2. Select Display.
3. Select Wireless display or Cast screen (depending on your
version of Android).
4. Turn Wireless display ON and select the device name from
the list. By default Display Adapter will be listed as the device name. Tap the device to connect.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
18
Cast screen
5. The smartphone or tablet screen will now be shared on your
Display Device.
Conguration
Accessing the Remote Control Interface
1. Once the Display Adapter is connected to your TV and
powered on, the Miracast Launch screen will show on the display.
2. Press the Mode Select button beside the USB port. A
secondary Launch screen will load.
Note: You will want to be in the same room as the display connected to the Display Adapter.
3. Connect your Smartphone, Tablet, or Laptop to the SSID of
the device. By default the SSID for the device is WIFI2HDMC xxx with no security key.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
19
4. Once you have connected to the device, open a web
browser and enter the IP address (http://192.168.59.254) in the address bar. The Airfun Launch screen will appear.
Note: The IP address is also listed on the display The default is http://192.168.59.254.
Airfun Launch screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
20
5. Select the Remote Control button to access the Remote
Control screen.
Remote Control screen
Conguring a Wired Connection
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Network tab.
3. Click on the Wired Connection link.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
21
Wired Connection Link
4. A pop-up screen will appear with the following options:
Obtain an IP address automatically: An IP address from
DHCP server will be assigned automatically.
Set IP address manually: Allows you to set an IP address
manually
Subnet Mask: Enter the Subnet Mask e.g. 255.255.255.0
Gateway Address: Enter the Routers address
DNS Server: Enter the IP address of the DNS (Domain
Name Service) server.
Changing the Device Name
The Device Name will be used as the SSID name while board casting in ad hoc mode and as the device name within the ScreenShare software.
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
22
Setup screen
2. From the Setup screen, click on the Network tab.
3. Click on the Device Name link.
Device Name Link
4. Enter the Device Name of the presentation gateway.
Note: The Device Name default is WIFI2HDMC.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
23
Conguring a WiFi Connection
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Network tab.
3. Click on the Wi Connection link.
Wi Connection link
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
24
4. A list of available wireless access points (AP) will be
displayed.
5. Select the desired wireless AP.
Note: The selected wireless AP may require a password.
Conguring Virtual AP
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Network tab.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
25
3. Click on the Virtual AP Setup link.
Virtual AP Setup link
4. A pop-up screen will appear with the following options:
Radio Band: Set the Radio band to 2.4GHz or 5GHz.
Note: Please conrm that your PC/Notebook supports 5GHz operation before you set the radio band to 5GHz.
Security:
Open: Disables wireless encryption.
WPA: Enable WPA encryption. Wireless clients must
support WPA encryption and know the encryption pass­phrase you set here.
Region: Choose your region.
5. Click the Save button to save the changes to the virtual AP
conguration.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
26
Creating a Bridge to a Wireless Connection
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Network tab.
Network tab
3. Click on the Wi Connection link.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
27
4. A list of available wireless access points (AP) will be
displayed.
5. Select the desired wireless AP.
Note: The selected wireless AP may require a password.
Creating a Bridge to a Wired Connection
1. Connect a LAN Cable from the Display Adapter to the AP
Router.
2. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
3. From the Setup screen, click on the Network tab.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
28
Network tab
4. Click on the Wired Connection link.
5. A pop-up screen will appear with the following options:
Obtain an IP address automatically: An IP address from
DHCP server will be assigned automatically.
Set IP address manually: Allows you to set an IP address
manually
Subnet Mask: Enter the Subnet Mask e.g. 255.255.255.0
Gateway Address: Enter the Routers address
DNS Server: Enter the IP address of the DNS (Domain
Name Service) server.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
29
Conguring Night Mode
Night Mode allows you to keep theater sounds at a lower volume. It increases the level of low level audio while decreasing the level of high level audio.
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
30
2. From the Setup screen, click on the Audio tab.
Audio screen
3. Click the Night Mode link to enable or disable the mode.
Setting HDMI Output Method
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Audio tab.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
31
Audio screen
3. Click the HDMI Output link and select an HDMI Output
Method from the drop-down list.
Conguring a Surround Sound Mode
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Audio tab.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
32
Audio screen
3. Click the Surround Sound link and select a mode from the
drop-down list.
Conguring Lip Sync Mode
Lip Sync mode synchronizes audio and video together so no audio delay is visible within the video.
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
33
2. From the Setup screen, click on the Audio tab.
Audio screen
3. Click the Lip Sync link and select a mode from the drop-
down list.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
34
Conguring Aspect Ratio
Allows you to manually set a video aspect ratio.
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Video tab.
Video screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
35
3. Click the Aspect Ratio link and select a ratio from the drop-
down list.
Conguring a TV System
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Video tab.
Video screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
36
3. Click the TV System link and select an option from the drop-
down list.
Scaling Video Output
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Video tab.
Video screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
37
3. Click the Scale Video Output to 90% link to enable or
disable the feature.
Conguring Video Output
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the Video tab.
Video screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
38
3. Click the 1080p 24Hz link to enable or disable the feature.
Setting the On-Screen Display Language
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the System tab.
System screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
39
3. Click the Language link and select a language from the
drop-down list.
Resetting the Display Adapter to Factory Settings
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
2. From the Setup screen, click on the System tab.
System screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
40
3. Click on the Factory Default link to reset the Display
Adapter to the factory defaults.
4. Power cycle the Display Adapter for the changes to take
place.
Resetting the Display Adapter’s IP Address
The Reset button is located on the bottom of the Display Adapter.
1. Using a Pen gently press and hold the recessed Reset button
for 10 seconds while the Display Adapter is still connected to the AC Power Adapter.
2. The IP Address and Name will return to the factory default
setting.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
41
Checking the Current Firmware Version
Note: the rmware version can also be found on the Screen­Share Home screen.
1. From the Remote Control screen, click on the Setup Button,
the Setup screen will appear.
Setup screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
42
2. From the Setup screen, click on the System tab.
System screen
3. Click on the Version Info link to see the current rmware
version.
Note: To update the rmware please refer to the Updating
Firmware section of the manual.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
43
ScreenShare Mode
Installation
Note: New versions of this product do not include a Driver CD. Please visit www.StarTech.com/WIFI2HDMC and
navigate to the Drivers/Downloads tab to download the latest Drivers.
1. Ensure you have .NET Framework version 3.5 installed prior
to installing ScreenShare
2. Insert the included software CD into the computer’s CD/DVD
drive. You may also download the latest version from our website.
3. Run the Autorun.exe application from the Autoplay menu. If
Autoplay is disabled on your system, browse to your CD/DVD drive and run the application.
4. Choose Typical Installation from the following screen and
click Install.
Quick Installer screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
44
5. Follow the on screen instructions to complete the
installation.
6. When nished, restart the computer.
Logging into ScreenShare
1. Switch the Display Adapter device into ScreenShare
mode by pressing the Mode Select button on the Display Adapter (located next to the USB connector).
2. The Home screen will appear on the Display.
Note: The Login Code will be displayed at the bottom of the screen.
Login Code
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
45
3. On your Notebook / PC, search and connect to the Display
Adapter’s SSID (wireless network) on the Wireless Network Connection screen.
Wireless Network Connection screen
4. Click the ScreenShare icon from your desktop or Start
Menu.
ScreenShare Icon
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
46
5. ScreenShare will auto detect the Display Adapter. Enter
the input Login Code that is located in the top right-hand corner of the Home screen as indicated in step 2, then click OK.
ScreenShare Login screen
Checking the MAC Address
The MAC address can be found on the Home screen, and is
located on the bottom right of the Home screen.
Checking the MAC Address
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
47
ScreenShare Panel Controls
1. Once you have logged into the ScreenShare app the Panel
Control screen will appear.
Panel Control screen
2. From the Panel Control screen the following controls are
available:
Play/Pause: Starts or pauses the presentation.
Stop: Stops the presentation and returns to the
Information screen.
Menu: Allows you access to advance menu options.
Login Code: Displays the current login code.
Mute: Mutes the volume of the presentation.
Volume Up/Down: Turns the volume of the presentation
up or down.
Information: Displays application information (adapter
name, IP address, radio band, version).
Minimize: Minimizes the Panel Control screen to the
Taskbar.
Close: Closes the Panel Control screen.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
48
Conguring a Display Mode
1. From the Panel Control screen, select the Menu icon.
2. The Menu screen will appear.
Menu screen
3. Select the Display Mode link, a pop-up screen will extend.
Display Mode screen
4. Select either:
Mirror Mode: Mirrors the content on the main display.
Extend Mode: Extends the main display’s viewing area
two multiple displays allow for a larger display area.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
49
5. Select which display the mode will apply to.
Select a display
Conguring a Display Resolution
1. From the Panel Control screen, select the Menu icon.
2. The Menu screen will appear.
Menu screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
50
3. Select the HDMI Resolution link, a pop-up screen will
extend.
HDMI Resolution screen
4. Select a Resolution from the pop-up screen.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
51
Conguring the Display’s Aspect Ratio
1. From the Panel Control screen, select the Menu icon.
2. The Menu screen will appear.
Menu screen
3. Select the Aspect Ratio link, a pop-up screen will extend.
Aspect Ratio screen
4. Select an Aspect Ratio from the pop-up screen, which
allows you to set the width and height ratio of the display.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
52
Enabling Auto Resolution
1. From the Panel Control screen, select the Menu icon.
2. The Menu screen will appear.
Menu screen
3. Select the Settings link, the Settings screen will appear.
Setting screen
4. Select Enable Auto Adjust Resolution to enable/disable
automatic resolution adjustments.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
53
5. Click the Apply button to save the changes made on the
Settings screen.
Enabling Auto Save
1. From the Panel Control screen, select the Menu icon.
2. The Menu screen will appear.
Menu screen
3. Select the Settings link, the Settings screen will appear.
Setting screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
54
4. Select Enable Auto Save to enable/disable the auto save
function.
5. Click the Apply button to save the changes made on the
Settings screen.
Exiting the ScreenShare App
1. From the Panel Control screen, select the Menu icon.
2. The Menu screen will appear.
Menu screen
3. Select the Exit link.
4. A Conrmation screen will appear asking Do you really
want to exit? click the Yes button to exit to the Login screen.
- or -
Click the No button to return to the ScreenShare App.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
55
Playing Media from a USB Stick
1. Connect your Smartphone/Tablet or Notebook to the
WIFI2HDMC device and navigate to the Setup (remote) page using a web browser.
2. Plug your USB stick into the port located on the side of the
WIFI2HDMC device.
3. Navigate the USB stick contents using the web remote to
choose the video, music or picture le you would like to view.
AirFun Utility
Installation
Note: New versions of this product do not include a Driver CD. Please visit www.StarTech.com/WIFI2HDMC and
navigate to the Drivers/Downloads tab to download the latest Drivers.
The AirFun utility is available for PC (on the included software CD), iPhone or Android platforms.
Android/iPhone
Download and install the latest version of the AirFun utility
from your mobile app store.
PC
1. Insert the included software CD into the computer’s CD/
DVD drive, or download the latest drivers from http://www. starTech.com.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
56
2. Run the Autorun.exe application from the Autoplay menu. If
Autoplay is disabled on your system, browse to your CD/DVD drive and run the application.
3. Select Software Installation from the menu.
4. Choose Typical Installation from the following screen and
click Install.
Note: This will install both the AirFun and the ScreenShare utilities (outlined later in this manual). Should you only desire to install only the AirFun utility, choose Custom Installation and de-select Screenshare.
5. Follow the on screen instructions to complete the
installation(s).
Operation
Android/iPhone
1. Open the AirFun app, it will begin to automatically search for
the Display Adapter.
Searching for a Device
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
57
2. Once found, tap the buttons for either Photo/Music
Playback or Video Playback and choose the le you wish to view/play.
Please choose a scenario screen
PC
1. Click the AirFun icon from your desktop or Start Menu.
AirFun Icon
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
58
2. The AIRFUN utility will begin to search for the WIFI2HDMC
device. If the device is not found before the timeout period, it will display No device found.
Found Device screen
3. If successfully connected, you should be able to see your PC
screen on the TV.
AirFun app
4. Drag the video/photo/music le to the Airfun main menu
directly.
5. For video les, drag les to the Video Playback folder.
6. For photo/music les, drag les to the Photo/Music
Playback folder.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
59
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall it be the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
60
60
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.
Reviews
Share your experiences using StarTech.com products, including product applications and setup, what you love about the products, and areas for improvement.
StarTech.com Ltd.
45 Artisans Cres.
London, Ontario
N5V 5E9
Canada
FR: fr.startech.com
DE: de.startech.com
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
ES: es.startech.com
NL: nl.startech.com
StarTech.com Ltd.
Unit B, Pinnacle
15 Gowerton Rd., Brackmills
Northampton
NN4 7BW
United Kingdom
IT: it.startech.com
JP: jp.startech.com
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Loading...