Startech USBDUP15 User Manual
Portable 1:5 USB Flash Drive
Duplicator and Eraser
USBDUP15
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 07/23/2014
*actual product may vary from photos
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
Table of Contents
Product Diagram ....................................................................................1
Top View .......................................................................................................................................................1
Back View ..................................................................................................................................................... 1
Introduction ............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements .............................................................................................................................. 2
Hardware Setup ......................................................................................3
User Menu Table of Contents ................................................................................................................ 4
Hardware Operation ................................................................................................................................ 5
1.2 Asynchronous Copy .......................................................................................................................... 6
2. Compare .................................................................................................................................................. 7
3. Copy + Compare ................................................................................................................................... 7
4. Capacity Check ...................................................................................................................................... 8
5. Information ............................................................................................................................................. 8
6. Utility ......................................................................................................................................................... 9
6.2 Measure Speed ................................................................................................................................... 10
7. Setup ......................................................................................................................................................... 11
Technical Support ..................................................................................14
Warranty Information ............................................................................14
Instruction Manual
i
Product Diagram
Top View
5 4
1
3
2
1. Source USB drive port
2. Destination USB drive ports
3. LCD Display
4. Forward button
5. Backward button
6. OK button
7. Escape button
Back View
1. Power Adapter Port
2. Power Switch
6
7
2
1
Instruction Manual
1
Introduction
Packaging Contents
• 1x 1:5 USB Flash Drive Duplicator (USBDUP15)
• 1x Universal Power Adapter (NA/UK/EU)
• 1x Instruction manual
System Requirements
• 1x Source USB drive
• 1 to 5x Destination USB drive(s)
• (Optional) USB multimedia card reader (1 x each drive): To use an SD/ SDHC/ Micro
SD/ MMC/ Mini SD/ CF card as Source or Destination drive.
• (Optional) USB to SATA Hard Drive docking station/USB to SATA enclosure: To use a
solid state drive (SSD) or hard drive (HDD) as Source or Destination drive.
Instruction Manual
2
Hardware Setup
Note:
a) Before you begin ensure the power switch on the USBDUP15 is set to the o
position.
b) The source or destination drives can be replaced with any SD/ SDHC/ Micro SD/
MMC/ Mini SD/ CF media card, using USB multimedia card reader (sold separately),
or Hard Drive(HDD) / Solid State Drive (SSD) through a Hard Drive docking station or
USB enclosure (sold separately).
1. Insert the source USB ash drive you would like to copy into the Source USB drive
port on the USBDUP15.
2. Insert up to 5 destination USB ash drives (that you would like to be over written
with the same data that is currently on the source drive) into the destination USB
drive ports.
WARNING! Any DATA on the destination USB Flash drives will be overwritten.
3. Connect the power adapter port on the USBDUP15 to an available power source
using the included Universal power adapter.
4. Set the power switch on the USBDUP15 to the on position.
5. The USBDUP15 is now is ready for operation as the user menu appears on the
LCD display.
Instruction Manual
3
Loading...