Page 1
2 Port USB 2.0 Extender over Cat5e, Cat6, or Cat7 | Locally or Remotely Powered | Up to 330 ft (100 m)
Quick-Start Guide
Product Diagram (USB2002EXT2NA)
Front
Rear
Component Function
1 USB-A Ports
1
5 6 7
2
• Used to connect USB Devices (mouse, keyboard,
etc.) to the Remote Extender.
Power:
• Solid Blue: The Extenders are receiving power.
Link:
• Solid Green: The Extenders are linked.
• O: The Extenders are not linked.
2 LEDs (Local/Remote)
Host:
• Solid: Extender is linked to the Host Computer.
• Flashing: Extenders are in suspend mode.
Activity:
4
3
• Flashing: Data is transmitted between Extenders.
• O: Extenders are in a suspended mode.
3 Mode Button • Used for rmware management/updates.
4 Cong Port • Used for rmware management/updates.
Power Port 24V 1A
5
(Local/Remote)
RJ45 Port - Link (Local/
6
Remote)
7 USB-B Host Port
• Used to connect the Local and Remote Extender
to AC Electrical Outlets, using the Power Adapter
(included).
• Used to connect the Local Extender to the Remote
Extender.
• Max. data transfer rate = 480Mbps
• Used to connect the Local Extender to a Host
Computer, using the USB Cable (included).
Requirements
For the latest requirements, please visit www.startech.com/USB2002EXT2NA
• USB Enabled Host Computer
• Solid Core Cat5e unshielded twisted pair (UTP) or greater
Installation
1. Position the Local Extender near the Host Computer and an AC Electrical Outlet.
2. Position the Remote Extender near an AC Electrical Outlet.
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: May 31, 2021 2:46 PM
Page 2
3. Connect a Cat5e Cable (or better) to the RJ45 Port on the Local Extender and the
other end to the RJ45 Port on the Remote Extender.
Note: The Cat5e Cabling cannot go through any networking equipment (router,
switch, etc.).
4. Connect the USB Cable (included) to the USB-B Host Port on the Local Extender
and the other end to a USB port on the Host Computer.
5. Connect the Power Adapter (included) to the Power Port on either the Local or
Remote Extender and the other end to an AC Electrical Outlet.
6. Connect USB Devices to the USB-A Ports on the Remote Extender.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
EU Declaration of Conformity
We, StarTech.com, declare under our sole responsibility that the USB2002EXT2NA to which this declaration relates, is in
conformity with European Standards EN 55024, EN 55032, EN 61000, and RoHS Directive 2011/65/EU + 2015/863/EU.
WEEE Statement
The European Union has established regulations for the collection and recycling of all waste electrical and electronic equipment
(WEEE). Implementation of WEEE regulations may vary slightly by individual EU member states. Please check with your local and
state government guidelines for safe disposal and rec.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
Loading...