1:1 HDD/SSD Duplicator with Image
Library Backup & Restore
SATDUP11IMG
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 05/12/2014
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
Table of Contents
Product Diagram ....................................................................................1
Front View ....................................................................................................................................................1
Rear View ...................................................................................................................................................... 1
Introduction ............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements .............................................................................................................................. 2
Hardware Installation ............................................................................3
Hardware Operation ................................................................................................................................ 4
Restore a HDD Image from an Image Library Drive ..................................................................... 6
1:1 Hard Drive Duplication .................................................................................................................... 7
Technical Support .................................................................................. 8
Warranty Information ............................................................................8
Instruction Manual
i
Product Diagram
Front View
1
6
1. Display Screen
2. UP Navigation Button
3. Down Navigation Button
4. OK button
5. Esc button
6. SATA SSD/HDD Source Port
7. SATA SSD/HDD Target Port
Rear View
7
5
4
3
2
1. Power Switch
2. Power Adapter Port
Instruction Manual
1 2
1
Introduction
Packaging Contents
• 1:1 HDD/SSD Image Duplicator (SATDUP11IMG)
• Long SATA cable (DATA+Power)
• 2x Short SATA cable (DATA+Power)
• eSATA + 12V Power Cable (Type M Power Connector)
• eSATA + 5V Power Cable (Type F Power Connector)
• 2x HDD/SSD Pads
• Universal power adapter (UK/NA/EU)
• Instruction Manual
System Requirements
• 1x SATA/eSATA Source Drive (HDD/SSD)
• 1x SATA/eSATA Target Drive (HDD/SSD)
Instruction Manual
2
Hardware Installation
WARNING! Hard drives and drive duplicators require careful handling, especially
when being transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and duplicator device with caution. Be sure that
you are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
1. Ensure the power switch is set in the o position. Using the included Universal
Power Adapter, connect the Power Adapter Port on the back of the
SATDUP11IMG to an available power outlet.
2. Connect your Source drive to the SATA SSD/HDD Source Port on the
SATDUP11IMG.
Note: The Source Drive can be drive you intend to make an exact copy of, or an
Image drive containing several hard drive images.
a) If the source drive is a SATA HDD/SSD, use the included Long SATA cable or the
included Short SATA cable depending on your preference.
b) If your source drive is an eSATA HDD/SSD, use the included eSATA + 12V Power
Cable or eSATA+5V Power Cable depending on your drive requirements.
Instruction Manual
3
3. Connect your Target drive to the SATA SSD/HDD Target Port on the
SATDUP11IMG.
Note: The Target Drive can be a drive you intend to overwrite with another drive
image, or an Image drive you intend to add an additional drive image to.
a) If the target drive is a SATA HDD/SSD, use the included Long SATA cable or the
included Short SATA cable depending on your preference.
b) If your target drive is an eSATA HDD/SSD, use the included eSATA + 12V Power
Cable or eSATA+5V Power Cable depending on your drive requirements.
4. For added drive protection and heat insolation, place the source drive and target
drive on top of each, of the included SSD/HDD Pads.
5. Set the Power Switch to the on position. The SATDUP11IMG is now ready to use.
Hardware Operation
Create an Image Library Drive/Add an Image to your HDD Image Library Drive
Note: The target drive must be larger than the source drive to create an Image Drive,
or add an HDD image to your Image Drive. The Image Library Drive must also be
formatted correctly to be recognized as an image drive. Be aware that any previous
data on the library drive will be overwritten if it need to be setup as a library drive.
1. Using the UP/DOWN Navigation buttons and the Display Screen, locate 1.Copy
from the on screen menu, and press the OK button, to access the [Copy] sub menu.
Instruction Manual
4
2. Using the UP/DOWN Navigation buttons and the Display Screen, locate 1.HDD ->
Image, on the [Copy] sub menu, and press the OK button.
3. The SATDUP11IMG will analyze the source drive and ensure the target drive is
ready, by verifying size and format.
a) If the target drive has not been formatted as an Image drive, the SATDUP11IMG will
alert you on the display screen, Press the OK button.
WARNING! Formatting your HDD/SSD will delete all data stored on the target drive.
b) Press the OK button again to format your target drive as an Image drive.
4. Once the drives have been analyzed (and if necessary, formatted the SATDUP11IMG
will begin to copy your SSD/HDD image to the Image Drive.
5. The image will be completely copied when the % indicator on the Display Screen
reaches 100%. The image drive now contains the drive image (and if working with a
non-formatted drive, an image drive has also been created.)
Instruction Manual
5
Restore a HDD Image from an Image Library Drive
WARNING! The drive attached to the Target port will be overwritten, deleting all data
currently stored on the drive.
Note: The target drive must be equal to or larger than the source drive Image. If the
target drive is larger than the source drive image, any additional space will remain
unformatted.
1. Using the UP/DOWN Navigation buttons and the Display Screen, locate 1.Copy
from the on screen menu, and press the OK button, to access the [Copy] sub menu.
2. Using the UP/DOWN Navigation buttons and the Display Screen, locate
2.Image-> HDD, on the [Copy] sub menu, and press the OK button.
3. The SATDUP11IMG will analyze the source Image Library Drive and ensure the
target drive is ready, by verifying size and format. Using the UP/DOWN Navigation
buttons and the Display Screen, select the drive image you would like to copy over
to the target drive and press the OK button.
4. Once the drives have been analyzed (and if necessary, formatted), you will receive
an indicator stating the SATDUP11IMG is ready and begin the duplication process.
5. The drive image duplication will be complete when the % indicator on the Display
Screen reaches 100%. The image drive now contains the drive image (and if
working with a non-formatted drive, an image drive has also been created.)
Instruction Manual
6
1:1 Hard Drive Duplication
WARNING! The drive attached to the Target port will be overwritten, deleting all data
currently stored on the drive.
Note: The target drive must be equal to or larger than the source drive. If the target
drive is larger than the source drive, any additional space will remain unformatted.
1. Using the UP/DOWN Navigation buttons and the Display Screen, locate 1.Copy
from the on screen menu, and press the OK button, to access the [Copy] sub menu.
WARNING! Proceeding will overwrite your target drive with the data on your source
drive, deleting all data currently stored on the target drive.
2. Using the UP/DOWN Navigation buttons and the Display Screen, locate 3. HDD->
HDD, on the [Copy] sub menu, and press the OK button.
3. The SATDUP11IMG will analyze the source drive and ensure the target drive is
ready, by verifying drive size, and begin the duplication process.
4. The drive duplication will be complete when the % indicator on the Display Screen
indicates the duplication has reached 100%. The target drive is now a duplicate of
the source drive.
*For advanced operation please download the complete product manual
at StarTech.com
Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
8
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...