Startech SATDUP11IMG User Manual

1:1 HDD/SSD Duplicator with Image
Library Backup & Restore

SATDUP11IMG

*actual product may vary from photos

DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com

For the most up-to-date information, please visit: www.startech.com

Manual Revision: 08/25/2014

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual

Table of Contents

Product Diagram ....................................................................................1

Front View ....................................................................................................................................................1

Rear View ...................................................................................................................................................... 1

Introduction ............................................................................................2

Packaging Contents ................................................................................................................................. 2

Hardware Installation ............................................................................2

User Menu Table of Contents ...............................................................5

User Menu Table of Contents ...............................................................6

Hardware Operation ..............................................................................6

1. Copy .......................................................................................................................................................... 6

2. Compare .................................................................................................................................................. 11

3. Copy & Compare ................................................................................................................................... 11

4. Image Manager ..................................................................................................................................... 12

5. Utility ......................................................................................................................................................... 13

6. Setup ......................................................................................................................................................... 17

Technical Support .................................................................................. 20

Warranty Information ............................................................................20

Instruction Manual

i

Product Diagram

Front View

SATA HDD

Source Port

Navigation

Buttons

Rear View

Ok Button

Esc Button

Display Screen

SATA HDD

Target Port

Instruction Manual

Power Switch

1

Power Adapter

Port

Introduction

Packaging Contents

• 1 x HDD Duplicator/Eraser

• 2 x 10cm SATA Cables

• 2 x 50cm SATA Cables

• 1 x eSATA + 5V DC Type F Power Cable

• 1 x eSATA + 12V DC Type M Power Cable

• 1 x Power Adapter

• 3 x Power Cords (NA, UK, EU)

• 2 x HDD Pads

• 1 x Instruction Manual

WARNING! Hard drives and storage enclosures require careful handling, especially
when being transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and storage device with caution. Be sure that
you are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.

Hardware Installation

WARNING! Hard drives and drive duplicators require careful handling, especially
when being transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and duplicator device with caution. Be sure that
you are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.

1. Ensure the power switch is set in the o position. Using the included Universal

Power Adapter, connect the Power Adapter Port on the back of the
SATDUP11IMG to an available power outlet.

Instruction Manual

2

2. Connect your Source drive to the SATA SSD/HDD Source Port on the SATDUP11IMG.

Note: The Source Drive can be a drive you intend to make an exact copy of, or an
Image drive containing several hard drive images.

a) If the source drive is a SATA HDD/SSD, use the included Short SATA cable or
the included Long SATA cable if the drive is installed into a PC chassis.

b) If your source drive is an eSATA HDD/SSD Enclosure or Dock, use the
included eSATA + 12V Power Cable or eSATA+5V Power Cable depending
on your drive requirements.

3. Connect your Target drive to the SATA SSD/HDD Target Port on the SATDUP11IMG.

Note: The Target Drive can be a drive you intend to overwrite with another drive
image, or an Image drive you intend to add an additional drive image to.

a) If the target drive is a SATA HDD/SSD, use the included Short SATA cable or
the included Long SATA cable if the drive installed into a PC Chassis.

b) If your target drive is an eSATA HDD/SSD Enclosure or Dock, use the included
eSATA + 12V Power Cable or eSATA+5V Power Cable depending on your
drive requirements.

Instruction Manual

3

4. For added drive protection and heat insolation, place the source drive and target
drive on top of each, of the included SSD/HDD Pads.

5. Set the Power Switch to the on position. The SATDUP11IMG is now ready to use.

Instruction Manual

4

User Menu Table of Contents

1.1 HDD > Image

1. Copy

2. Compare

3. Copy+Compare

4. Image Manager

5. Utility

5.1 Show HDD Info

(Select Device 1 or Device 2 depending

on your preference)

1.2 Image > HDD

1.3 HDD > HDD

2.1 HDD > Image

2.2 Image > HDD

2.3 HDD > HDD

3.1 HDD > Image

3.2 Image > HDD

3.3 HDD > HDD

4.1 Show HDD Info

4.2 Show Image Info

4.3 Rename Image

4.4 Delete Image

4.5 Format HDD #2 (Setup Image Drive)

5.1.1 Model Number

5.1.2 Version of Firmware

5.1.3 Serial Number

5.1.4 Device Power Cycle

5.1.5 Power-on Hours

5.1.6 Reallocation Event Count

5.1.7 O-Line Scan Uncorrectable

5.1.8 Seek Error Rate

5.1.9 Temperature

Instruction Manual

5