How it Works
Startech
Loading...
RK1232WALHM
Product Data Sheet
5 pgs108.21 Kb0
User Manual
22 pgs1.56 Mb0
Table of contents
Loading...

Startech RK1232WALHM User Manual

Download
12U Hinged Wall-Mount Rack Enclosure
Actual product may vary from photos
User Manual
SKU#: RK1232WALHM
For the latest information and specications visit
www.startech.com/RK1232WALHM
Manual Revision: 03/08/2019

Compliance Statements

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
1

Safety Statements

Safety Measures
• Wiring terminations should not be made with the product and/or electric lines under power.
• Product installation and/or mounting should be completed by a certied professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un professionnel certié et dans le respect des normes locales et du code de construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent être placés et acheminés de façon à éviter tout risque électrique, de chute ou de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでくださ い。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に 従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう にしてください 。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un tecnico professionale certicato che conosca le linee guida locali sulle norme edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o pericoli per la sicurezza.
2
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.

Warning Statements

• Make sure that you assemble this product according to the instructions.
• Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: Stationary = 198 lb. (90 kg).
• This product is intended for indoor use only and should not be used outdoors.
• This enclosure is extremely heavy. Never attempt to move or lift this enclosure without assistance.
• Tipping hazard! Extending multiple components from this enclosure increases the chance that the enclosure will tip over. To avoid this risk, do not extend more than one component from the enclosure.
• Do not place any items on this enclosure and do not stack the enclosure on top of another enclosure.
• Keep liquid away from this enclosure.
• Make sure that you install the enclosure in an area that can handle the combined weight of the enclosure and the equipment that you intend to place inside of the enclosure.
• This product requires an earth ground connection. Do not use this product without an earth ground connection.
Varningar
• Se till att du monterar produkten i enlighet med instruktionerna.
• Överskrid inte produktens vikt kapacitet. Överbelastning av denna produkt kan leda till skador eller skador på egendom. Denna produkt kan stödja följande vikt: stationär: 90 kg.
• Produkten är endast avsedd för användning inomhus och ska inte användas utomhus.
• Detta skåp är extremt tungt. Försök aldrig ytta på skåpet eller lyfta det utan hjälp.
• Risk för vältning! Att förlänga era komponenter från detta skåp ökar risken
3
för att det välter. Förläng inte er än en komponent från skåpet för att undvika risk.
• Placera inte saker ovanpå skåpet och ställ inte skåpet ovanpå ett annat skåp.
• Håll vätskor borta från skåpet.
• Se till att du installerar skåpet på en plats som kan hantera den kombinerade vikten av skåpet och utrustningen som du tänker placera inuti.
• Produkten behöver en jordad anslutning. Använd inte produkten utan en jordad anslutning.
Avertissements
• Assemblez ce produit conformément aux instructions.
• Ne dépassez pas la capacité pondérale de ce produit. Une surcharge de ce produit peut entraîner des dommages corporels ou matériels. Ce produit peut supporter le poids suivant, stationnaire = 90 kg.
• Ce produit est uniquement destiné à une utilisation en intérieur et ne doit pas être utilisé à l’extérieur.
• Ce rack de serveur est extrêmement lourd. Ne tentez jamais de le déplacer ou de le soulever sans aide.
• Risque de basculement! L’extension de plusieurs composants à partir du rack de serveur augmente le risque de basculement. Pour éviter ce risque, n’étendez pas plus d’un composant à partir du rack de serveur.
• Ne placez aucun objet sur ce rack de serveur et n’empilez pas le rack sur un autre rack.
• N’approchez aucun liquide du rack de serveur.
• Veillez à installer le rack de serveur dans un endroit pouvant supporter le poids combiné du rack et des équipements que vous comptez placer à l’intérieur.
• Ce produit nécessite un raccordement à la terre. N’utilisez pas ce produit sans raccordement à la terre.
Warnhinweise
• Beachten Sie bei der Montage dieses Produkts die Montageanweisungen.
• Überschreiten Sie nicht die Tragfähigkeit dieses Produkts. Das Überladen dieses Produkts kann zu Verletzungen oder Sachschäden führen. Dieses Produkt kann das folgende Gewicht tragen: Stationär = 90 kg.
• Dieses Produkt ist nur zum Gebrauch in Innenräumen vorgesehen und sollte nicht im Freien verwendet werden.
• Dieses Gehäuse ist extrem schwer. Versuchen Sie niemals, dieses Gehäuse ohne Hilfe zu bewegen oder anzuheben.
• Kippgefahr! Das Ausziehen mehrerer Komponenten aus diesem Gehäuse
4
erhöht die Chance, dass das Gehäuse umkippt. Um dies zu vermeiden, ziehen Sie niemals mehr als eine Komponente aus diesem Gehäuse aus.
• Platzieren Sie keine Gegenstände auf dem Gehäuse und stapeln Sie das Gehäuse nicht auf einem anderen Gehäuse.
• Halten Sie Flüssigkeiten von diesem Gehäuse fern.
• Vergewissern Sie sich, dass der Untergrund, auf dem das Gehäuse aufgestellt wird, in der Lage ist, das Gesamtgewicht des Gehäuses und der Geräte, die Sie darin platzieren möchten, zu tragen.
• Dieses Produkt erfordert einen Schutzleiteranschluss. Verwenden Sie das Produkt nicht ohne einen Schutzleiteranschluss.
Dichiarazioni di avvertenza
• Assicurarsi di Assemblare il prodotto secondo le istruzioni.
• Non superare la capacità di carico massimo di questo prodotto onde evitare danni o lesioni alla proprietà. Questo prodotto e’ in grado di supportare il peso riportato, Statico = 90 kg.
• Il prodotto è destinato all’uso in ambienti interni. Se ne sconsiglia l’impiego in ambienti esterni.
• Il box esterno è molto pesante. Non tentare di spostarlo o sollevarlo senza assistenza.
• Pericolo di ribaltamento! L’estensione di più componenti dal box esterno aumenta il rischio di ribaltamento del box esterno. Per evitare questo rischio, non estendere più di un componente dal box esterno.
• Non collocare oggetti sul box esterno e non impilare un box esterno sopra un altro.
• Tenere il box esterno lontano dai liquidi.
• Assicurarsi di installarlo in un punto che possa sorreggere il peso combinato del box esterno e dell’apparecchiatura che si intende collocare al suo interno.
• Il prodotto richiede una messa a terra. Non utilizzare il prodotto in assenza di una messa a terra.
Mensagens de aviso
• Certique-se de que monta este produto de acordo com as instruções.
• Não exceda a capacidade de peso deste produto. Sobrecarregar este produto pode resultar em ferimentos ou danos à propriedade. Este produto pode suportar o seguinte peso: estacionário: 90 kg.
• Este produto destina-se apenas a uma utilização no interior e não deve ser utilizado no exterior.
• Esta caixa é extremamente resistente. Nunca tente mover ou levantar esta caixa sem assistência.
5
• Perigo de queda! Estender vários componentes desta caixa aumenta a probabilidade desta caixa cair. Para evitar este risco, não expandir mais de um componente desta caixa.
• Não colocar nenhum artigo nesta caixa e não empilhar a caixa em cima de outra caixa.
• Manter líquidos afastados desta caixa.
• Certique-se de que instala a caixa numa área que pode suportar o peso combinado da caixa e o equipamento que pretende colocar dentro da caixa.
• Este produto requer uma ligação à terra. Não utilize este produto sem uma ligação à terra.
Advertencias de uso
• Asegúrese de ensamblar este producto según las instrucciones.
• No exceda la capacidad de carga de este producto. El sobrecargarlo puede ocasionar lesiones y daños en propiedad. Este producto puede soportar el siguiente peso, Estacionario = 90 kg.
• El uso de este producto es solo para interiores y no debe utilizarse en exteriores.
• La caja es extremadamente pesada. Nunca intente mover o alzar esta caja sin la debida asistencia de otra persona.
• ¡Peligro de vuelco! Añadir a esta caja varios componentes aumenta las posibilidades de peligro de vuelco de la caja. Para evitar dicho riesgo, no añada más que un solo componente.
• No coloque ningún elemento encima de la caja y no apile la caja encima de otra caja.
• Mantenga cualquier líquido lejos de la caja.
• Asegúrese de instalar la caja en un área que tenga capacidad para soportar el peso combinado de la caja y el equipo que va a instalar dentro de la misma.
• Este producto requiere conexión a tierra. No utilice este producto sin conexión a tierra.
Waarschuwingen
• Zorg dat u dit product volgens de instructies in elkaar zet.
• Overschrijd de maximale capaciteit van dit product niet. Overbelasting De maximale gewichtscapaciteit mag niet overschreden worden. Overbelasting kan kan letsel of schade tot gevolg hebben. Dit product kan het volgende gewicht ondersteunen, stationair = 90 kg.
• Dit product is alleen bedoeld voor binnengebruik en mag niet buiten worden gebruikt.
• Deze behuizing is enorm zwaar. Probeer nooit deze behuizing te verplaatsen
6
of op te tillen zonder hulp.
• Kantelgevaar! Wanneer meerdere componenten uit deze behuizing steken, bestaat de kans dat deze zal kantelen. Om dit risico te voorkomen, mag niet meer dan één component uit de behuizing steken.
• Plaats geen voorwerpen op deze behuizing en stapel de behuizing niet op een andere behuizing.
• Houd vloeistof uit de buurt van deze behuizing.
• Zorg dat u de behuizing installeert op een plaats die geschikt is voor het gecombineerde gewicht van de behuizing en de apparatuur die u in de behuizing wilt plaatsen.
• Dit product vereist een geaarde verbinding. Gebruik dit product niet zonder een geaarde verbinding.
注意
• 必ず取扱説明書に従って本製品の組み立てを行って下さい。
• 本製品で定められた可搬重量を超えないようにして下さい。規定された 重量を超えた場合、怪我や物的損害が発生することがあります。本製品は 次の可搬重量に対応していいます。[キャスター静止時]＝90kg
• 本製品は、室内での使用を想定しています。戸外では使用しないで下さ い。
• 本製品は、非常に重いエンクロージャです。絶対に一人で持ち上げたり 動かしたりしないで下さい。
• 転倒注意！本製品から複数のコンポーネントが突き出した状態にしてお くとエンクロージャが転倒する恐れがあります。転倒リスクを回避するた めに、エンクロージャからはコンポーネントが突き出ないようにして下 さい。
• 本製品の上に何も載せないで下さい。複数のエンクロージャを重ねて設 置しないで下さい。
• 液体物をエンクロージャに近づけないようにして下さい。
• エンクロージャ自身と中に積載する装置の総重量に耐えられるエリアに 設置して下さい。
• この製品にはアースが必要です。アース接続をしていない状態で本製品 を使用しないでください。
7
Table of Contents
Compliance Statements ........................................................................1
Safety Statements ..................................................................................2
Warning Statements ..............................................................................3
Product Diagram ....................................................................................9
Product Information ..............................................................................10
Package contents ...................................................................................................................................... 10
Requirements ............................................................................................................................................. 10
Ground the Enclosure ............................................................................11
Lock or unlock the front or rear door ..................................................12
Remove the side panels ........................................................................12
Installing the Side Panels ......................................................................13
Access your cables .................................................................................14
Replacing the Cable Covers ..................................................................15
Reverse the front door ..........................................................................15
Adjust the depth of the mounting rails ..............................................17
Mount the enclosure to the wall ..........................................................18
Install equipment ...................................................................................19
8

Product Diagram

7
4
5
5
6
6
8
8
2
1
7
3
1 Front Door 5 Cable Access Cover
2 Rear Door 6 Cable Access Opening
3 Horizontal Mounting Rail 7 Side Panel
4 Vertical Mounting Rail 8 Vent
9

Product Information

Package contents

• Wall-mount enclosure x 1
• 1U shelf x 1
• Roll of hook-and-loop fastener x 1
• 12-24 cage nuts x 48
• 12-24 screws x 48
• Door keys x 2
• Side panel keys x 2
• Instruction manual x 1

Requirements

• Phillips type screwdriver
• Appropriate tools and mounting hardware for the type of
wall you’re using
Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/RK1232WALHM.
10

Ground the Enclosure

Warning! This product must be grounded. Do not use this product without an earth ground connection.
1. Use an M6 screw to attach a grounding wire to the front or
rear grounding point on the enclosure.
2. Route the wire under the frame of the enclosure and
connect the wire to your facility’s earth ground connection.
Grounding Wire
11

Lock or unlock the front or rear door

For additional security, the front and rear door of the enclosure can be locked with the provided door keys.
• To lock or unlock the front or rear door of the enclosure,
insert one of the provided door keys in the lock on the door and turn the key clockwise or counterclockwise.

Remove the side panels

1. If the side panels are locked, use the provided side panel
keys to unlock the panels.
2. Pull the two tabs on the side panel towards the center of the
panel.
Removing the Side Panel
12
3. While using proper lifting techniques, remove the side panel
from the enclosure.
Removing the Side Panel from the Enclosure
4. Repeat steps 1 to 3 to remove the other side panel.

Installing the Side Panels

To put the side panels back on the enclosure:
1. Place one of the side panels in the groove at the bottom of
the enclosure.
2. Pull the two tabs on the side panel towards the center of the
panel, push the top part of the side panel into the enclosure, and release the tabs.
13
3. Use one of the provided side panel keys to lock the side
panel.

Access your cables

There are two cable access covers on the enclosure that you can remove to access and manage your cables.
1. To take o a cable access cover, use a Phillips type
screwdriver to remove the two screws on both ends of the cable access cover.
2. Pull the cable access cover away from the enclosure. (gure
4)
Removing the Cable Covers
14

Replacing the Cable Covers

To put the cable access cover back on:
1. Place the cover over the cable access opening
2. Use a Phillips type screwdriver to insert the screws through
the cover and into the enclosure.
3. Tighten the screws.

Reverse the front door

To accommodate dierent rack congurations, you can reverse the front door of the enclosure so that it opens to the left or right of the enclosure.
1. In the top corner of the inside of the front door, pull the lever
down and move the top corner of the front door away from the enclosure.
2. In the bottom corner of the inside of the front door, pull the
lever up and remove the front door from the enclosure.
15
Door Release Levers
3. Flip the front door so that the levers are located on the
opposite side.
4. Position the front door so that the top and bottom levers are
aligned with the washers located in the hinge area of the enclosure.
5. In the top corner of the front door, pull the lever down and
release it into the washer and hole in the enclosure.
6. In the bottom corner of the front door, pull the lever up and
release it into the washer and hole in the enclosure.
16

Adjust the depth of the mounting rails

The mounting rails come pre installed in the enclosure. Both the front and back set of mounting rails can be adjusted independently in 3/4 inch (20 mm) increments.
Warning! Do not attempt to adjust the mounting rails when equipment is installed in the enclosure. Remove the equip­ment rst before you adjust the mounting rails.
1. Each of the mounting rails is connected to the enclosure
with a screw and cage nut in the upper and lower corners of the mounting rail. Use a Phillips type screwdriver to remove the screws and cage nuts from the mounting rails.
2. Install the cage nuts at the desired depth.
3. Slide the mounting rail to the depth of the cage nuts and use
a Phillips type screwdriver to install and tighten the screws that you removed in step 1.
Move the Mounting Rails
17

Mount the enclosure to the wall

Warning! Remove all equipment from the enclosure before you attempt to mount the enclosure to the wall.
Wall structures vary and it is important to make sure that the type of wall structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall structure should be capable of supporting at least four times the weight of the mounted equipment.
The RK1232WALHM weighs 99 lb. (45 kg) and can hold up to 198 lb. (90 kg) in weight.
Warning! If you lack the necessary expertise to attach this product to the wall that you’re using, contact a construction professional to install the enclosure or to provide specic mounting instructions for your wall structure.
The number of mounting holes on the rear door of the enclosure will vary depending on the model of your enclosure. Each mounting hole can accommodate an M8, M10, 5/16”, or 3/8” bolt.
• Follow the appropriate steps for the type of wall that you’re
attaching the enclosure to and attach the enclosure to the wall.
Caution! The enclosure is extremely heavy and you should not attempt to lift and hang the enclosure without the assistance of other people.
18

Install equipment

Warning! Do not add equipment to the enclosure until the enclosure is securely attached to the wall.
When you load equipment into this enclosure, load the heaviest equipment in the bottom section of this enclosure rst. Continue loading equipment in a descending order of weight, so that the lighter equipment is installed in the upper sections of this enclosure and the heavier items are on the bottom.
This enclosure comes with cage nuts and screws but the equipment you’re installing may come with mounting hardware. Consult the documentation that came with the equipment to determine the best mounting hardware that you should use and how you should install it.
1. Decide where in the enclosure you want to install the
equipment and insert the cage nuts in the mounting rails.
2. Line up the mounting holes on the equipment with the cage
nuts.
3. Insert the screws through the mounting holes on the
equipment and into the cage nuts.
19
Warranty Information
This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall it be the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
20
20
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.
Reviews
Share your experiences using StarTech.com products, including product applications and setup, what you love about the products, and areas for improvement.
StarTech.com Ltd.
45 Artisans Cres. London, Ontario N5V 5E9 Canada
FR: fr.startech.com DE: de.startech.com
StarTech.com LLP
2500 Creekside Pkwy. Lockbourne, Ohio 43137 U.S.A.
ES: es.startech.com NL: nl.startech.com
StarTech.com Ltd.
Unit B, Pinnacle 15 Gowerton Rd.,
Brackmills Northampton NN4 7BW United Kingdom
IT: it.startech.com JP: jp.startech.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use