Startech GNDBAR1U User Manual
Instruction manual
Copper grounding bar for server racks
GNDBAR1U
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
Packaging contents
• 1 x copper grounding bar (1U or 10U)
• 12 x M5 (20 mm) screws
• 2 x M5 cage nuts
• 1 x instruction manual
System requirements
• A server rack with 1U of free space (horizontal installation) or 10U
of free space (vertical installation)
System requirements are subject to change. For the latest
requirements, please visit www.startech.com/GNDBAR1U.
Product overview
Install the grounding bar
The grounding bar can be installed either horizontally or vertically,
and can be installed on the inside or the outside of your server rack.
Using the holes located along the length of the grounding bar, you
can connect and ground up to ten devices.
1. Decide whether you want to install the grounding bar horizontally
or vertically, and select the area on your server rack where you
want to install the grounding bar.
2. Insert the included M5 cage nuts in the holes in your server rack
that line up with the mounting holes on the end of the grounding
bar.
3. Line up the mounting holes on the end of the grounding bar with
the holes in which you inserted the cage nuts.
Mounting hole Grounding hole
*actual product may vary from photos
For the latest information, technical specications, and support for
this product, please visit www.startech.com/GNDBAR1U.
4. Holding the grounding bar in place, insert the included M5 (20
mm) screws into the mounting holes located on each end of the
grounding bar.
5. Use a screwdriver to tighten the screws.
6. Attach the devices that you want to ground to the holes located
along the length of the grounding bar.
Note: If you install the grounding bar vertically and inside of the
server rack, the mounting screws used to hold equipment may need
to be replaced with the provided M5 (20 mm) screws.
Manual Revision: 05/07/2015
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the
equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and
access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two-year warranty.
StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for
repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not
allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Loading...