Startech BRACKET125PT User Manual

Instruction manual

2.5” SSD/HDD Mounting Bracket for 3.5” Drive Bay - Tool-less Installation

BRACKET125PT

FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com

Important: Read and understand the entire manual before
you use this product, and follow the instructions as they are
outlined in the manual.
Failure to do so might result in property damage or device
failure.

Introduction

You can use the BRACKET125PT to install a 2.5 in. SSD (solid-state
drive) or HDD (hard disk drive) into a 3.5 in. drive bay. The tool-less
design of the BRACKET125PT makes it easy to install drives.

Product diagram

Package contents

• 1 x 2.5 in. SSD/HDD to 3.5 in. mounting bracket

• 6 x plastic pegs

• 1 x instruction manual

System requirements

• Computer with an available 3.5 in. drive bay

• One 2.5 in. SSD or HDD

The operating system of your computer will detect the drive and
automatically install it.

System requirements are subject to change. For the latest
requirements, please visit www.StarTech.com/BRACKET125PT.

Install the drive and bracket

Warning! Hard drives and storage enclosures should be handled

carefully, especially when they’re transported. If you’re not careful
with your drives, you may experience lost data as a result. Always
handle storage devices with caution. Make sure that you’re properly
grounded by wearing an anti-static strap when you install any
computer component. If an anti-static strap isn’t available, touch a
large grounded metal surface for several seconds to discharge any
built-up static electricity.

Tenon
(plastic projections)

Plastic post

Plastic peg

For the latest information, technical specications, and support for
this product, please visit www.StarTech.com/BRACKET125PT.

*actual product may vary from photos

1. Remove the six Plastic pegs from the Plastic posts that are
attached to the mounting bracket.

2. Pull the Plastic posts o of the mounting bracket and discard the
posts.

3. Align your SSD or HDD with the Tenons (plastic projections) on
the mounting bracket, and gently push the drive into place.

4. Turn o your computer and any devices or peripherals that are
connected to it (for example, printers, external hard drives, and
so on).

5. Unplug the power cable from the back of your computer.

6. Disconnect any peripheral devices that are connected to your
computer.

7. Remove the cover from your computer case. Consult the
documentation that came with your computer for details about
how to do this safely.

8. Place the bracket into the 3.5 in. hard drive slot, and use the
Plastic pegs that you removed in step 1 to secure the drive in
place.

9. Connect a power connection from the computer’s power supply
to the drive’s power connector.

(continued on next page)

Manual Revision: 07/10/2016

10. Use the appropriate cable and connect the drive to the host
controller.

11. Place the cover back onto your computer case.

12. Reconnect the power cable to the back of your computer and
reconnect all of the peripheral devices that you previously
disconnected.

13. Turn on your computer and any peripherals that are connected
to it.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and
access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two-year warranty.
StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for
repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not
allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.