Startech BEZ4MOD User Manual

Single-Module Conference Table Box
User Manual
SKU#: BEZ4MOD
Actual product may vary from photos
For the latest information and specications visit
www.startech.com/BEZ4MOD
Manual Revision: 07/16/2019

Compliance Statements

For the State of California
WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Safety Statements

Safety Measures
• Wiring terminations should not be made with the product and/or electric lines under power.
• Product installation and/or mounting should be completed by a certied professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
1
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un professionnel certié et dans le respect des normes locales et du code de construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent être placés et acheminés de façon à éviter tout risque électrique, de chute ou de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでください。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に従い、有資格の専門業者が行うようにしてください。
• ケーブル(電源ケーブルと充電ケーブルを含む)は、適切な配置と引き回しを行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう にしてください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un tecnico professionale certicato che conosca le linee guida locali sulle norme edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o pericoli per la sicurezza.
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.

Warning Statements

Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage.
Never use this product if parts are missing or damaged.
2
Table of Contents
Compliance Statements ........................................................................1
Safety Statements ..................................................................................1
Warning Statements ..............................................................................2
Product Diagram ....................................................................................4
Product Information ..............................................................................5
Package Contents ..................................................................................................................................... 5
Requirements ............................................................................................................................................. 6
Installation ..............................................................................................7
Cutting the Table/Surface ...................................................................................................................... 7
Installing the Module in the Modular Table Box ............................................................................10
Installing the Lacing Bar (Cable Organization) ............................................................................... 13
Installing the Modular Table Box into a Surface ............................................................................. 14
Assembling the Cable Management Module ....................................16
Assembly Requirements: ........................................................................................................................ 16
Installing the Cable Management Module ...................................................................................... 17
3

Product Diagram

Installation
Holes
Mounting
Slot
Lacing Bar
Mounting
Holes (2)
4

Product Information

Package Contents

BOX4MODULE
• Modular Table Box x 1
• Installation Kit
• Wing Fastener x 2
• Die Cut Outline x 1
• Lacing Bar x 1
• Lacing Bar Screws (M4 x 4 mm) x 4
• Cable Management Module
• Cable Management Bracket x 1
• Cable Management Top Plates x 2
• Cable Management Plate Screws (#6-32 x 3/8”) x 4
• Cable Management Bracket Mounting Screws (#6-32 x 3/8”) x 4
• Small Cable Bushing x 1
• Large Cable Bushing x 1
• User Manual x 1
5
Loading...
+ 14 hidden pages