Desk Mount Articulating Monitor Arm with Cable
Management and Gas Spring Height Adjust
ARMPIVOTE
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 03/19/2018
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
Table of Contents
Introduction ............................................................................................ii
Packaging Contents ................................................................................................................................. ii
Product Diagram ....................................................................................1
Installation ..............................................................................................2
Desk / Grommet Mounting ................................................................................................................... 2
Attaching the Display .............................................................................................................................. 4
Attaching the Gas Spring Arm Assembly ......................................................................................... 5
Cable Management .................................................................................................................................. 6
Adjusting the Gas Spring Arm Resistance ........................................................................................ 7
Specications ..........................................................................................9
Technical Support ..................................................................................10
Warranty Information ............................................................................10
Instruction Manual
i
Introduction
Packaging Contents
13
Instruction Manual
Plastic Gasket Cushion
Qty.2
ii
Product Diagram
Instruction Manual
1
Installation
WARNING! It is the installer’s responsibility to ensure that the combined weight
of all components does not exceed the maximum 8 lb (3.6 kg) weight capacity of
the mounting arm.
Desk / Grommet Mounting
The Monitor Arm can be clamped to a desk / table, or mounted through a grommet
hole. Instructions for both will be provided in the steps below.
1. Desk / Grommet Clamp: Remove the Left Cover and insert the L Plate portion of
the Clamp (4) into the base of the Pole (3) before replacing the Left Cover, then
apply the Plastic Gasket Cushions (13) as shown.
Instruction Manual
2
2. Desk Clamp: Attach the bottom portion of the Clamp (4) to the L Plate, then place
the Clamp (4) opening around the edge of your desktop in your desired location
and tighten by hand to secure. Ensure that the Clamp is making full contact with
the desk surface.
Grommet Clamp: Place the L Plate through the grommet hole of your desk surface,
then attach the bottom portion of the Clamp (4) to the L Plate and tighten by hand to
secure. Ensure that the Clamp is making full contact with the desk surface.
3. Loosen the collar on the support post and adjust to the desired height.
Instruction Manual
3
Attaching the Display
1. Carefully place your display face down on a protective surface to access the
mounting points.
2. Depending on the depth of the mounting holes on your display, attach the display
to the Gas Spring Arm (1) using either the M4x12mm (11) screws, or the M4x25mm
(12) screws with spacers (10). Tighten using a Phillips screwdriver.
WARNING! Do not over-tighten the screws and stop immediately if you encounter
resistance to avoid damage to your display. Ensure that all spacers and screws being
used are the same length and thread type.
Instruction Manual
4
Attaching the Gas Spring Arm Assembly
1. Slide the Extension Arm (2) down onto the Pole (3).
2. Slide the Gas Spring Arm (1) onto the Extension Arm (2).
3. Place the Cover and Bolt (9) onto the Gas Spring Arm (1) and press the bolt down to
secure the two arms together.
Instruction Manual
5
Cable Management
Note: When attaching cables and routing through the cable management channels,
ensure that you leave enough slack to avoid stretching / pulling out the cables when
moving the arm.
1. Connect your cables to your display and position the mounting arm in its fully
extended position to ensure that the cables you are using are long enough to
allow for proper movement.
2. Feed the cables into the cable management channels on the underside of the
arms as shown.
3. Press the Cable Covers (8) into the slots as shown.
Instruction Manual
6
4. Use the Cable Clip (7) to secure the display cables to the pole.
Adjusting the Gas Spring Arm Resistance
WARNING! Forced movement of the LCD Arms or Mount Brackets without loosening
the screws may damage the product or the mounted displays.
Always support your display from underneath when making any adjustments to the
LCD Arms or Mount Brackets to avoid damage to the display.
Note: For all adjustments outlined below, turning the screw clockwise will increase the
resistance, while turning the screw counter-clockwise will decrease resistance.
Instruction Manual
7
To increase / decrease the Gas Spring Arm resistance, adjust the set screw located at
the elbow of the articulating arm, using the 4mm Allen Wrench (5).
To increase / decrease the tilt resistance, adjust the set screw located on the side of the
Mount Bracket joint, using the 6mm Allen Wrench (6).
Instruction Manual
8
Specications
Weight Capacity 8 lb (3.6 kg)
Max Display Size 24”
VESA Compatibility 75 x 75 mm and 100 x 100 mm
Maximum Extension 22.05 in (560mm)
Maximum Mounting Surface Thickness 2.95 in (75 mm)
Instruction Manual
9
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
10
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...