Startech ARMDUAL30 User Manual

Dual Monitor Arm with Full-Motion Articulation - Stackable
ARMDUAL30
*actual product may vary from photos
FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com
For the latest information, technical specications, and support for this product, please visit www.startech.com/ARMDUAL30.
Manual Revision: 09/13/2019
Table of Contents
Introduction ............................................................................................1
Packaging contents .................................................................................................................................. 1
Product diagrams ...................................................................................2
Technical specications ..........................................................................................................................3
Attach the ARMDUAL30 to a desk or table ........................................4
Convert the desk mount to a grommet mount ............................................................................. 4
Convert the grommet mount to a desk mount ............................................................................. 5
Use the grommet mount to attach the ARMDUAL30 ..................................................................6
Use the 2-in-1 desk mount to attach the ARMDUAL30 ...............................................................7
Attach the monitor arms .......................................................................8
Set up the monitors side-by-side ........................................................................................................ 8
Stack the monitors vertically ................................................................................................................ 9
Attach the monitors ...............................................................................13
Route the monitor cables .....................................................................14
Disassemble the ARMDUAL30 .............................................................15
Technical support ................................................................................... 16
Warranty information ............................................................................16
Instruction manual
i

Introduction

The ARMDUAL30 is a full-articulation monitor mount that lets you mount and display your monitors in the setup that works best for you. The snap-and-release assembly makes the ARMDUAL30 easy to assemble and customize. Customizing options include assembling the mounting arms vertically or horizontally; using the dual mount attachment or attaching the mounting arms directly to the pole; changing the placement of the spring and swivel arms, and more.

Packaging contents

1.
2-in-1 desk or
grommet mount
Qty: One
5.
Spring arm
Qt y: Two
9.
Quick-release
cable manager
Qt y: Two
Instruction manual
2.
M6 Allen key
Qt y: Two
6.
Swivel arm
Qt y: Two
10.
Dual mount
Qty: One
3.
M3 Allen key
Qt y: Two
7.
VESA monitor
mount
Qt y: Two
11.
Instruction manual
Qty: One
1
4.
Base cushion
Qty: One
8.
Thumbscrews
Qty: Eight

Product diagrams

VESA monitor
mount
Spring arm Spring arm
Cable manager
2-in-1 desk or grommet mount
(grommet pictured)
Swivel arm Swivel arm
Dual mount
VESA monitor mount
Instruction manual
2
Technical specications
Type of movement Measurement
Lift
Angle
Pivot
Swivel
Pan
Tilt
Extension
160 mm
100
360
360
240
105
590 mm
Instruction manual
Vertical
270 mm
Weight load
Do not exceed 20 kg
3
There are four main tasks that you need to complete when you assemble the ARMDUAL30: Attach the ARMDUAL30 to a desk or table, attach the monitor arms, attach the monitors, and route the monitor cables.

Attach the ARMDUAL30 to a desk or table

By default, the ARMDUAL30 comes with the desk mount preassembled.

Convert the desk mount to a grommet mount

1. Turn the 2-in-1 desk mount (1) over so that the pole faces downwards. Use one of the M3 Allen keys (3) to remove the four M5x14 mm hex screws that are holding the base of the pole to the desk clamp (gure 1).
gure 1
M5x14 mm hex screw (x4)
2. Use a Phillips screwdriver (not included) to remove the M3 Phillips screw from the
plate on the desk mount (gure 2).
3. Remove the plate, two washers, and the thumbscrew from the bottom of the desk
mount (gure 2).
4. Use a Phillips screwdriver (not included) to remove the four M6x12 mm screws that
are holding the two parts of the desk mount together (gure 3).
Instruction manual
gure 2
Washers
gure 3
4
M3 Allen key
M3 screw
Plate
Thumbscrew
M6x12 mm screws

Convert the grommet mount to a desk mount

By default, the ARMDUAL30 comes with the desk mount preassembled. If you assemble the grommet mount and want to switch back to a desk mount, you will need to use the screws and hardware that you removed when you converted the ARMDUAL30 to a grommet mount.
1. Use a Phillips screwdriver (not included) to insert four M6x12 mm screws into the
two halves of the desk mount (1) (gure 4).
Note: Depending on the height of the desk or table, use the top four holes or the bottom four holes in the desk mount.
gure 4
or
M6x12 mm screws
M6x12 mm screws
2. Insert the thumbscrew through the hole in the desk mount (gure 5).
gure 5
Thumbscrew
3. Place a male washer onto the thumbscrew.
4. Place a Phillips M3 screw through a female round washer, the plate, and into the
male washer on the thumbscrew (gure 6).
gure 6
M3 screw
Female washer
Male washer
Plate
Thumbscrew
Instruction manual
5
5. Turn the 2-in-1 desk mount over and use one of the M3 Allen keys (3) to insert four
M5x14 mm hex screws through the desk mount and into the base of the mount (gure 7).
gure 7
M3 Allen key
M5x14 mm hex screw (x4)

Use the grommet mount to attach the ARMDUAL30

1. Remove the plastic from the base cushion (4) and attach it to the bottom of the
base mount. Make sure that you line up the hole on the base mount with the corresponding hole on the base cushion.
2. Position the base mount over the grommet hole (gure 8).
3. Place the thumbscrew through the grommet hole in your desk or table and into the
pole on the base mount.
4. Turn the thumbscrew clockwise to tighten it (gure 9).
gure 8
Desk thickness 20 to 50 mm
gure 9
Base mount
Base cushion (not pictured)
Desk hole 10 to 60 mm
Instruction manual
Thumbscrew
6

Use the 2-in-1 desk mount to attach the ARMDUAL30

1. Remove the plastic from the base cushion (4) and attach it to the bottom of the
base mount. Make sure that you line up the hole on the base mount with the corresponding hole on the base cushion.
2. Turn the thumbscrew on the desk mount (1) counterclockwise until you reach the
thickness of the desk or table (gure 10).
Note: The desk mount can accommodate a desk or table between 20 and 100 mm thick.
3. Slide the desk mount over the edge of the desk or table.
4. Turn the thumbscrew clockwise to tighten it (gure 11).
gure 10
Thumbscrew
gure 11
Instruction manual
7

Attach the monitor arms

Set up the monitors side-by-side

Note: If you want to position your monitors side by side at exactly the same height, use
the dual mount to attach the monitor arms. Using the dual mount adds approximately two inches of distance between the two monitors.
1. To loosen the tension of the cable manager (9), pull out the lever and turn the knob
counterclockwise (gure 12).
gure 12
Cable manager
2. Slide one of the cable managers over the pole and move the cable manager to the
height that you want the monitor arms to be at.
3. Push the lever closed and turn the knob clockwise to tighten the cable manager
until it doesn’t move up or down on the pole.
4. Slide the dual mount (10) down the pole until it’s sitting on the cable manager
(gure 13).
gure 13
Dual mount
Cable manager
5. Snap the swivel arms (6) onto the dual mount (gure 14).
Dual mount
Instruction manual
gure 14
Swivel arm
8
6. If necessary, use the M3 Allen key (3) with the dual mount to increase or decrease
the swing tension of the swivel arms (gure 15).
Tip: Place the M3 Allen key into the holder on the cable manager so that you don’t lose it when it’s not in use (gure 16).
gure 15
gure 16
M3 Allen key
Dual mount
Cable manager
M3 Allen key
7. Snap the spring arms (5) onto the swivel arms (gure 17).
gure 17
Spring arm
Swivel arm

Stack the monitors vertically

There are two ways that you can assemble the ARMDUAL30 so that the monitors are positioned vertically:
• Attach the monitor arms without the dual mount.
• Use the dual mount to attach the monitor arms and assemble the spring arms
below the swivel arms.
Warning! Do not attach more than two monitor arms together. The ARMDUAL30 is designed to only support two horizontal pieces (spring or swivel arms).
Attach the monitor arms without using the dual mount
1. To loosen the tension of the cable manager (9), pull out the lever and turn the knob
counterclockwise (gure 18).
Instruction manual
9
gure 18
Cable manager
2. Slide one of the cable managers over the pole and move the cable manager to the
height that you want the monitor arms to be at.
3. Slide one of the swivel arms (6) down the pole until it’s sitting on the cable manager
(gure 19).
gure 19
Swivel arm
Cable manager
4. Slide the second cable manager down the pole so that it’s sitting on the rst swivel
arm.
5. Slide the second swivel arm down the pole so that it’s sitting on the second cable
manager.
6. Snap the spring arms (5) onto the swivel arms (gure 20).
gure 20
Spring arm
Swivel arm
7. If necessary, use the M3 Allen key (3) to increase or decrease the swing tension of
the arms (gure 21).
Tip: Place the M3 Allen key into the holder on the cable manager so that you don’t lose it when it’s not in use (gure 22).
Instruction manual
10
gure 21
gure 22
M3 Allen key
Cable manager
M3 Allen key
Use the dual mount to attach the monitor arms
You can customize the ARMDUAL30 by changing the order in which you assemble the monitor arms or by using just the swivel arms or the spring arms. You can also assemble one set of monitor arms in one conguration and assemble the other set in a dierent conguration.
1. To loosen the tension of the cable manager (9), pull out the lever and turn the knob
counterclockwise (gure 23).
gure 23
Cable manager
2. Slide one of the cable managers over the pole and move the cable manager to the
height that you want the monitor arms to be at.
3. Push the lever closed and turn the knob clockwise to tighten the cable manager
until it doesn’t move up or down on the pole.
4. Slide the dual mount (10) down the pole until it’s sitting on the cable manager
(gure 24).
gure 24
Dual mount
Instruction manual
Cable manager
11
5. Snap the spring arms (5) onto the dual mount (gure 25).
gure 25
Spring arm
Dual mount
6. If necessary, use the M3 Allen key (3) with the dual mount to increase or decrease
the swing tension (gure 26).
Tip: Place the M3 Allen key into the holder on the cable manager so that you don’t lose it when it’s not in use (gure 27).
gure 26
gure 27
M3 Allen key
Dual mount
M3 Allen key
7. Snap the swivel arms (6) onto the spring arms (gure 28).
gure 28
12
Spring arm
Instruction manual
12
Cable manager
Swivel arm

Attach the monitors

If you’re positioning the monitors side-by-side, the maximum recommended size of monitors that you can use is 30 inches.
Warning! Each of the spring arms has factory-set tension to support monitors that weigh between 2.5 and 4.5 kg. If you attach a monitor that weighs less than 2.5 kg or
more than 4.5 kg, you will need to adjust the monitor mount.
1. If you attach a monitor that weighs less than 2.5 kg or more than 4.5 kg, do one of
the following:
• To decrease the weight capacity of the monitor mount, use the M6 Allen key (2) and turn the screw in the spring arms (5) clockwise.
• To increase the weight capacity of the monitor mount, use the M6 Allen key (2) and turn the screw in the spring arms (5) counterclockwise (gure 29).
Tip: The spring arms have positive and negative symbols next to the screw to remind you which way to turn the M6 Allen key.
2. Insert four thumbscrews (8) through the holes on the VESA monitor mount (7) and into the back of the monitor that you’re mounting (gure 30).
Warning! When you attach the monitor mounts to your monitors, make sure that you don’t scratch the monitors in the process.
gure 29
gure 30
M6 Allen key
Spring arm
Instruction manual
Monitor mount
Thumbscrew
13
3. Repeat step 2 for any additional monitors that you’re attaching.
4. If the monitor doesn’t stay in place or the movement is sti, do one of the following:
• To increase the tension, use the M3 Allen key (3) to turn the screws in the monitor
mount clockwise (gure 31).
• To decrease the tension, use the M3 Allen key to turn the screws in the monitor
mount counterclockwise (gure 31).
M3 Allen key
gure 31
Monitor mount

Route the monitor cables

The ARMDUAL30 comes with a cable manager that you can use to direct the monitor cables down the mounting arms and out of your working area.
Make sure that the cables that you’re routing are unplugged before you complete the following steps.
1. Run the cable along the spring arm (5) and through the cable manager depression on the underside of the spring arm (gure 32).
2. Thread the cable through the hole in the swivel arm (6) (gure 32).
3. Run the cable through the cable manager (9) on the side of the mounting pole (gure 32).
4. Repeat the steps for any additional monitors that you attached to the ARMDUAL30.
gure 32
Instruction manual
Spring arm
Cable manager
Swivel arm
14

Disassemble the ARMDUAL30

1. Remove the thumbscrews (8) from the back of the monitors and the monitor mounts (7).
Warning! Make sure that you lift the mounting arm up to its highest position when you remove the monitor. When you remove the weight of the monitor, the arm could bounce upward and cause injury.
2. To remove the monitor mounts and mounting arms, slide the textured button away from you on each of the mounts and arms and lift them up (gure 33).
3. Pull the mounting arm and the dual mount (if used) free from the pole.
4. To loosen the tension of the cable manager (9), pull out the lever and turn the knob counterclockwise, and remove the cable manager from the pole.
5. Remove the base of the ARMDUAL30 from the table or desk that it was attached to.
gure 33
Monitor mount
Instruction manual
Spring arm
Cable manager
Swivel arm
15

Technical support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads

Warranty information

This product is backed by a ten-year warranty.
StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Instruction manual
16
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...