Startech AP150WN1X1OE User Manual
Outdoor 150Mbps Wireless N Access Point 1T1R 2.4GHz
AP150WN1X1OD / AP150WN1X1OE / AP150WN1X1OG
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 09/25/2014
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
Déclaration d’exposition à la radiation:
Cet équipement respecte les limites d’exposition aux rayonnements IC dénies pour un
environnement non contrôlé. Cet équipement doit être installé et mis en marche à une distance
minimale de 20 cm qui sépare l’élément rayonnant de votre corps.
L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver à leur
proximité.
FCC ID: VYTLP-9318A
IC: 11232A- AP150WN1X1O
Instruction Manual
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Important Notice
This product MUST be installed by a professional installer who is familiar with local building
and safety regulations, where appropriate, and is licensed by applicable authorities. The
professional installer is responsible for making sure grounding is available and that it meets
the relevant local and national electrical codes. Failure to employ a professional installer may
render the product warranty void and it may also expose the end user or service provider to
legal and nancial liabilities. StarTech.com expressly disclaims any and all liabilities for injury,
damage, or violation of regulations due to improper installation of outdoor units or antennas.
Always remember to protect the AP by installing grounding lines as it is necessary to protect
your outdoor installations from lightning strikes and the build-up of static electricity. The AP
must be grounded properly before powering up, as direct grounding of an outdoor AP is
critical and must be done correctly to protect your networks from harsh outdoor environments
and destructive ESD surge.
CAUTION: Be sure that earth grounding is available and that it meets local and national
electrical codes. If in doubt always consult with a qualied electrician to make sure the outdoor
installation is properly grounded. For additional lightning protection, lightning rods, lightning
arrestors or RJ45 surge protectors may be used to compliment the installation.
Instruction Manual
3
Table of Contents
Product Diagram ....................................................................................1
Rear View ...................................................................................................................................................... 1
Introduction ............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements .............................................................................................................................. 2
Connection Ports ....................................................................................3
LED Indicators............................................................................................................................................. 4
Installation ..............................................................................................4
Preparing Your Site ................................................................................................................................... 4
Hardware Installation ............................................................................5
Operation ................................................................................................6
Advanced Conguration ........................................................................................................................8
Wireless Settings ....................................................................................................................................... 9
Smart Features ........................................................................................................................................... 14
IP Settings .................................................................................................................................................... 16
Management Settings ............................................................................................................................. 17
Password Settings (recommended) ...................................................................................................18
Specications ..........................................................................................19
Technical Support .................................................................................. 20
Warranty Information ............................................................................20
Instruction Manual
i
Product Diagram
Rear View
LED Panel
Pole/Wall
Mount Bracket
Instruction Manual
Interface Cover
1
Introduction
Packaging Contents
• 1 x Outdoor Access Point
• 1 x PoE Injector
• 1 x Metal Hose Clamp
• 1 x Power Adapter
• 1 x Quick Start Guide (CD)
System Requirements
• A networked computer system with a Java-enabled web browser (for conguration)
• Cat 5 (or better) network cabling from PoE Injector to Wireless AP and PoE Injector
to LAN Switch/router (no more than 100m total)
• Mounting screws / anchors if wall mounting PoE Injector and/or Wireless AP
Instruction Manual
2
Connection Ports
External Antenna
(optional)
Interface Description
External RP-SMA Antenna connector (optional).
External Antenna
PoE Port
LAN Port (secondary)
Instruction Manual
Upgradable to high gain antennas for more range. See
the External Antenna conguration section for setup
procedures.
Power over Ethernet RJ-45 port used to connect the
Access Point to the included PoE Injector for power and
data connectivity.
RJ-45 port used to connect additional network devices to
the Access Point.
PoE Port LAN Port
(Secondary)
3
LED Indicators
Indicator State Description
PWR
Wi activity
PoE
LAN
ON The device is powered on
O The device is powered o
Flashing Data is being transmitted / received over wireless
O No link detected
ON Link detected
O No link detected
Flashing
ON Link detected
O No link detected
Flashing
Data is being transmitted / received on the PoE LAN
interface
Data is being transmitted / received on the Secondary
LAN interface
Installation
Preparing Your Site
1. Determine the location for the included PoE injector and mount using the
appropriate screws/anchors for the material you are mounting to (not included).
2. Determine the location for the Wireless AP. If you are pole-mounting the AP, use
the included clamp to secure the device. If you are wall mounting the AP, use the
appropriate screws/anchors for the material you are mounting to (not included).
3. Prepare/purchase the required length of Ethernet cabling to go from the PoE
Injector to your LAN Switch or router, and from PoE Injector to the AP.
Note: The total length of Ethernet cabling from the Wireless AP to your LAN switch or
router should not exceed 100m.
Instruction Manual
4
Loading...