10/100 VDSL Ethernet Extender Kit over
Single Pair Wire 1km
110VDSLEXT
110VDSLEXTGB
110VDSLEXTEU
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 05/29/2012
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
Table of Contents
Introduction ...........................................................................................1
Package Contents .....................................................................................................................................1
Installation ..............................................................................................1
Hardware Installation ..............................................................................................................................1
Operation ................................................................................................2
LED Displays ................................................................................................................................................ 2
DIP Switch Settings ..................................................................................................................................2
Connector Architecture ......................................................................................................................... 5
Specications ..........................................................................................6
Technical Support ..................................................................................7
Warranty Information ............................................................................7
Instruction Manual
i
Introduction
Package Contents
• 2 x 110VDSLEXT/GB/EU units
• 2 x RJ-45 to VDSL Cable
• 2 x Power Adapter
• Instruction Manual
Installation
Hardware Installation
1. Install one of the 110VDSLEXT / GB / EU units with all four of the DIP switches set to
the upward (OFF) position. This places the unit in CO mode.
2. Install the second 110VDSLEXT / GB / EU unit with DIP switches 2 through 4 set to
the upward (OFF) position and DIP switch 1 set to the downward position (ON).
This places the unit in CPE mode.
3. Plug the DC power adapter into the port on the rear panel of the units, and then
into an available AC outlet.
4. Plug in an RJ45 Ethernet cable to the RJ45 port on the 110VDSLEXT / GB / EU units.
Connect the other end of the cables to your Ethernet devices.
5. Plug a phone cable into the VDSL port of the 110VDSLEXT/GB/EU. Connect the
other end of the cable into the opposing 110VDSLEXT/GB/EU unit.
6. Optional: Congure DIP switches 2 through 4 as necessary (see DIP Switch Settings
section). Leave DIP switch 1 alone, as one unit should always be set to CO mode
while the other is CPE mode.
Instruction Manual
1
Operation
LED Displays
LAN LED Display
LED Blinking ON OFF
1 Activity Link up Link down
2 100 Mbps 10 Mbps
3 Full duplex Half duplex
VDSL LED Display
LED Blinking ON OFF
1 Activity
2
3
-
Slowly: Idle
Quickly: Training
Device
Power On
CPE Mode CO Mode
Linked Oine
DIP Switch Settings
The 110VDSLEXT / GB / EU has a 4-position DIP switch for conguration of Side,
Channel, Rate Limit, and SNR.
Device Power O
Pin 1 - CO, CPE Switch
OFF: If Pin 1 is in the OFF position, the 110VDSLEXT / GB / EU will operate in Central
Oce (CO) mode.
ON: If Pin 1 is in the ON position, the 110VDSLEXT / GB / EU will operate in Customer
Premise Equipment (CPE) mode.
Instruction Manual
2
Pin 2 - Interleave Noise Protection
OFF: If Pin 2 is in the OFF position, the 110VDSLEXT / GB / EU will operate in Interleave
mode, with communication protection for up to 250ms of impulse noise with latency
less than 6 ms
ON: If Pin 2 is in the ON position, the 110VDSLEXT / GB / EU will operate in Fast mode,
with direct data transmissions having less than 1ms of latency.
Pin 3 - Band Plan
OFF: If Pin 3 is in the OFF position, the 110VDSLEXT / GB / EU will operate in Symmetric
mode, with both downstream and upstream transmissions operating on the G.997
band plan.
ON: If Pin 3 is in the ON position, the 110VDSLEXT / GB / EU will operate in Asymmetric
mode, with asymmetric short range transmissions operating at the highest available
line rate.
Instruction Manual
3
Pin 4 - General Protection
OFF: If Pin 4 is in the OFF position, the 110VDSLEXT / GB / EU will operate with a SNR
ratio up to 9 dB.
ON: If Pin 4 is in the ON position, the 110VDSLEXT / GB / EU will operate with a SNR
ratio of 6 dB.
Instruction Manual
4
Connector Architecture
Ethernet Port
Pin Number Assignment (MDI-X)
1 RX+; Receive data +
2 RX-; Receive data -
3 TX+; Transmit data +
4 Not used
5 Not used
6 TX-; Transmit Data -
7 Not used
8 Not used
VDSL Port
Pin Number Assignment (MDI-X)
1 Not used
2 Not used
3 Not used
4 ANALOG Input/Output
5
6 Not used
7 Not used
8 Not used
ANALOG Input/Output
Instruction Manual
5
Specications
110VDSLEXT
110VDSLEXTGB
110VDSLEXTEU
RJ-45 connector
LAN Interface
VDSL Interface
DIP Switch 4 position
LED
Power Supply 12VDC, 1A output, 3.5mm jack
Power Consumption 4.2 Watt maximum
Dimensions 95.5 mm x 72.0 mm x 22.0 mm
Complies with IEEE
802.3/802.3u/802.3x
10/100 Base-T Auto-Negotiation,
Auto-MDI/MDI-X
RJ-45 connector
DMT Encoding
Complies with ITU-T G993.1/993.2
On-board surge protection
LAN: ACT/LNK, 10/100 Mbps, Half/
Full Duplex
VDSL: Power On/O, CO/CPE, Idle/
Trained/Link
Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
7
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
Loading...