STARTASTIC™ ACTION LASER PROJECTOR ITEM NO.1035FE
Distributed by: High Street TV,
PO Box 724, Altrincham, WA15 5BJ
www.highstreettv.com
All rights reserved. Made in China.
Please read all instructions carefully and retain for future reference.
Laser classification: class IIIR
Operation: Outdoor/Indoor
Operating Temperature: -35°C to 37°C
Projection Coverage: 600 sq. ft.
Power Input: 100–240V AC
Maximum Power Output: less 5mW
Wavelengths: 532nm/650nm
SPECIFICATIONS :
ACTION LASER PROJECTOR
Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS:
When picking the location, keep in mind that there should be no visual obstructions between the Startastic
unit and the surface where the projection will show. This will ensure best results. Projection coverage - approx.
600 square feet. When using outdoors always plug into waterproof outlet.
Please read all instructions prior to use and save instructions for future reference.
1.
Locate the curved piece on the top part of the stake.
See Diagram 1.
Hold the stake so that its angled piece is pointing directly
at the surface for laser projection. Insert the stake into
the ground.
Make sure you insert the pointy end deep
enough for unit’s stability.
2. Insert the adjustment screw of the stake into the other side
of the Connector opening. Hold the nut in place with one hand,
while turning the knob clockwise to tighten. See Diagram 2.
3. Loosen the knob to adjust the angle (up or down) of the
laser projector. Tighten the knob to secure the position.
4. Connect to the unit’s plug. You should use the waterproof
outdoor electrical outlet to connect to.
5. IMPORTANT: Please note the laser will only turn on
in the dark due to the internal light sensor.
When on, the laser light will appear brightest in complete darkness,
and will appear dimmer in areas with additional light sources.
Pressing the ON/OFF switch towards the green mark will emit only green laser lights.
Pressing the ON/OFF switch towards the green and red mark will emit both red
and green lights.
Leaving the ON/OFF switch centered will turn off.
SELECT THE LOCATION FOR STARTASTIC LASER PROJECTOR
ASSEMBLY AND USAGE
Diagram 1
Knob
Caution - use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous
radiation exposure.
ATTENTION: StarTastic laser projector is intended to
operate in temperatures from -35� to 37�.
At or below freezing temperature, it may take approx.
10 min to warm up and reach its full projection strength.
NOTE: The unit will only work in the dark and will automatically shut off. Once it is dark,
unit will automatically
start projecting laser light, but not motion.To re-start the motion
laser light, press the Motion Switch.
MOTION:
NOTE: The unit will only work in the dark and will automatically shut off in daylight.
When you have selected either the green laser lights or red/green lights, you can press
the Motion Switch to activate the motion of the laser lights. To turn the motion off, press
the Motion Switch twice.
ON/OFF SWITCH
MOTION
SWITCH
CURVED PIECE
Diagram 1
Before using the electrical appliance, these basic
precautions should always be followed:
1. Read all instructions.
2. Please note the laser projector will only turn on
in the dark due to the internal light sensor.
3. This unit is not intended for use by individuals (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the use of the unit by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the unit.
4. Do not operate the laser projector with the damaged cord or plug.
5. Do not operate the laser projector if it has been damaged in any way.
6. To reduce the risk of electric shock, unplug the laser projector from the outlet when not in use.
7. Do not intentionally shine into eyes or face.
8. Do not attempt to open the housing of laser light under any circumstance.
9. Do not use near infants/cribs and keep away from children.
10. WARNING: Never look directly at the laser bulb
Loading...