Star Manufacturing International 49, 49D, 49SL, 59, 59D Installation And Operating Instructions Manual
...
Star
Manufacturing
International Inc.
10 Sunnen Drive
St. Louis, MO 63143
Installation
and
Operating
Instructions
Phone: (314) 781-2777
FAX: (314) 781-3636
COUNTER MODEL
POPCORN MACHINES
MODELS
49, 49D, 49SL
59, 59D, 59SL
89, 89D, 89SL
2M-8497 REV. C 1/30/90
REV.6-14-01RDB
1
GENERAL INSTALLATION DATA
CAUTION
This equipment is designed and sold for
commercial use only by personnel trained
and experienced in its operation and is not
sold for consumer use in and around the
home nor for use directly by the general
public in food service locations. For
equipment to be used by the general
public, please contact the factory.
THOUROUGHLY INSPECT YOUR
MACHINE ON ARRIVAL
We do everything in our power to insure
delivery of your machine in perfect
condition. However there are instances in
which the unit may be damaged in transit,
in the event your unit is damaged in
transit, have the transportation company
make the necessary notations on your
freight bill or delivery receipt. Immediately
report this damage to the dealer from
whom you purchased the machine. The
dealer will advise proper handling
Instructions. If damage is not discovered
until after delivery has been made, notify
the transportation company immediately.
However, in each instance, request an
inspection report to cover whatever damage
has occured in transit.
INSTALLATION
Each machine has been properly wired
and inspected at the Factory for operation
on the Voltage and type of Current
specified on the nameplate.
CAUTION
Do not connect to any other type of
current or the machine will be seriously
damaged.
A receptacle is furnished with the 89
Series Popcorn machines. We strongly
recommend installation by a Licensed
Electrician. The guarantee of this machine
as covered by the Warranty Card does not
apply if an improper installation has been
made.
120 VOLT MACHINES
Machines with nameplate stamped 120V,
are equipped for operation on 120 Volt, 2
wire, 60 Cycle AC single phase service
and must be connected to a separate 20
Amp circuit with a 3 wire grounded,
polarized receptacle.
240 VOLT MACHINES
Machines with nameplate stamped 240V,
are equipped for operation on 240 Volt, 2
wire, 60 Cycle AC single phase service
and must be connected to a separate 15
Amp circuit with a 3 wire grounded,
polarized receptacle.
GENERAL OPERATING
INSTRUCTIONS
CAUTION
The motor air intake and exhaust holes
located on top of the machine must be
clear of any obstruction.
DO NOT COVER THESE AIR VENT HOLES
as serious damage will result.
Check to insure the installation of the
Corn Drawer before the Popping cycle is
started. See picture for location of Corn
Drawer.
With all switches in the "OFF" position,
proceed in the following sequence to Pop
Corn:
1.) Turn "ON" the Corn Warming switch.
This switch controls the Bottom heating
element, the Top heating lamp and the
Sign diplay lamps of the Sign Lighted
models.
2.) Turn "ON" the Kettle switch. This
switch controls the Kettle heating
element. The Red pilot light is provided to
indicate when the Kettle switch is "ON".
Allow six to seven minutes to pre-heat the
Kettle. The Kettle heating element is
thermostatically controlled. Thermostat
adjustments should not be necessary as it
has been preset at the factory for the
2
correct popping temperature.
GENERAL OPERATING
INSTRUCTIONS - continued
3.) Turn "ON" the Agitator Motor switch
located at the right end of the motor
housing. This switch will function only
when the Kettle switch is in the "ON"
position. If the Kettle switch is turned
"OFF", the Motor will also stop. This Motor
should always be running when there is
corn in the Kettle. This will prevent
scorching or burning of corn.
4.) A Corn and Seasoning measuring cup
is supplied with your machine. Pour a
level measuring cup of Oil (2 ounces Models 49, 49D, 49SL, 59, 59D, 59SL and
3-1/2 ounces - Models 89, 89D, 89SL) in
Kettle. Add a level measuring cup of raw
corn (8 ounces - Models 49, 49D, 49SL,
59, 59D, 59SL and 14 ounces - Models
89, 89D, 89SL) and a Teaspoon of Popcorn
Salt. Vary the amount of salt and oil to
suit taste. If desired, salt may be added
adfter the Corn is popped.
5.) When the Corn stops popping, dump
the Kettle immediately by turning the
handle clockwise approximately 90
degrees to release latch. Recharge as
quickly as possible. Screen out unpopped
kernels over the perforated section of the
Corn pan.
6.) Turn the Kettle "OFF" when the
desired amount of popping is completed.
WARNING
Do not leave the Kettle and Motor switch
"ON" when the machine is not in use. Do
not immerse the Kettle in water or allow
water to come in contact with the Heating
element.
Popping Corn in dry kettle is not
recommended.
Do not connect machine to Direct Current,
as this unit is designed to operate on
Alternating Current only!
MAINTENANCE
Keep The Popping Unit Clean
After each popping period, wipe clean the
Kettle inside and out while it is warm.
This is important because if seasoning
and salt are not thoroughly removed, a
carbonized material will form. This
condition not only lowers popping
efficiency and causes excessive smoking,
but could damage the unit. For retaining
the high lustre on the stainless steel
Kettle shell and lids, use a non-abrasive
standard stainless steel cleaner when the
Kettle is cold. Use a damp cloth and a
warm mild soap solution to clean the glass
and clear plastic surfaces.
To remove Kettle:
Turn "OFF" the Kettle motor switches.
Disconnect the Twist Lock Cap at the end
of the Kettle conduit, turn Kettle handle
clockwise 90 degrees to unlatch the
Kettle, hold the Kettle and pull out the
hinge pin. The Kettle can now be removed
from unit. Use asbestos gloves to remove a
hot Kettle. DO NOT PLACE THE KETTLE
IN WATER, as this will damage the
electrical assembly.
To change Sign Display Lamps (on Sign
Lighted Models):
Turn "OFF" all switches. Unscrew 2 sheet
metal screws on the Rear side top (holding
switch and pilot light panel) and 4 screws
on the top. Cautiously take the top off.
Cahnge bulb(s) and reassemble the top
onto the frame. Tighten all six screws
securely. WARNING! Use only inside
Frosted Bulb. Wattage per label on the
surface of the Top Liner. By Authorized
Personnel Only.
MAINTENANCE and REPAIRS
Contact the Factory or one of its
representatives or a local Service
Company for Service or Maintenance
required.
3
MATERIAL
DR. PB CK. DATE 4-24-75
LIMITS UNLESS OTHERWISE NOTED
FRACTIONS +/- 1/64 , DECIMALS +/- .005
FINISH
STAR MANUFACTURING INT’L
10 SUNNEN DRIVE ST. LOUIS,MO 63143
MODEL NO. PART NO.
49, 49D
TITLE
WIRE DIAGRAM
CHANGES LTR DATE CHANGE DR
A 8-31-76 ADDED 49D MM
B 2-22-77 ADDED COLOR CODE TO JS
WIRES
C 9-14-78 ADD BOTTOM WARMER JS
D 3-25-83 SHOWED LAMP SYMBOL RT
ON HEAT LAMP
E 5-19-87 ADDED WIRE Q TH
F 5-11-89 UPDATED WIRE CODES MO
S
A
V
Y
2
P
M
3
4
Q
X
R
C
5
BK
WH
6
J
K
W
T
E
L
8
9
7
B
10
N
11
BK
WH
GR
G
1
1 CORD ASSEMBLY
2 120V - 250 WATT HEAT LAMP
3 120V AGITATOR MOTOR
4 AGITATOR MOTOR SWITCH
5 TWIST LOCK RECEPTACLE
6 TWIST LOCK PLUG W/1500
WATT KETTLE
7 HEAT LAMP SWITCH
8 KETTLE SWITCH
9 SIGNAL LIGHT (KETTLE SWITCH
ON)
10 WIRE CODES
11 WARMER ELEMENT
(ALL WIRES ARE #16 GA CUA1 WHITE STRD)
REV.6-14-01RDB
Old Style Hinge Bracket = N/A
Use C3-Y2611 + C3-Y2612 instead
Long Jumper
2C-9617
8 Oz. Kettle
49 Series
59 Series
PARTS LIST January 22, 2014
Model: 49 & 59 Kettle Series Popcorn Machines
Fig No Part Number Qty Description Application
C3-49009 NLA 1
1-31
1 2F-8351 1 CASTING KETTLE 8 oz
2 C3-8605 1 JUMPER LONG
3 2T-6213 1 THERMOSTAT, 550V B-200 1/4 TURN CLOWISE = 30°F RISE
4
5
7 C3-59024 1 ELEMENT CLAMP ASSY
8 2C-1810 3 WASHER 3/16 STL NP
9 2C-1512 3 SCREW 10-24X3/8 RHP STL
13 C3-Y4053 1 INSULATION MANNINGLAS
14 2C-8569 1 SCREW 1/4-20X2 ST SET
15-19 C3-59007 NLA 1 KETTLE HANDLE ASSY #4936652, #5916854 & BELOW
15 2P-8880 1 SPRING-HANDLE TORSION
16 2A-8838 1 ROD, HANDLE PLATED
17 2R-8293, NLA 1 HANDLE HARDWOOD BLACK
18 2C-1811 1 WASHER 1/4 STL
19 2C-2581 2 NUT 1/4-20 BR ACORN NP
24 2C-9607 1 SCREW-ADJUST SG1508 #4936652, #5916854 & BELOW
25 2A-5401 1 PIN-COTTER 3/32DX3/4 SS #4936652, #5916854 & BELOW
C3-49084 NLA 1 240V (49 & 59 SERIES)
C3-59025 NLA 1 120V (59& 59D SERIES)
C3-Y2611 1 BRACKET-KETTLE HINGE CP
C3-Y2612 1 BRACKET-KETTLE PLATED
2C-1589 2 SCREW, MACHINE
2C-Y1221 2 BOLT 1/4-20X1/2 HEX STL NP
KETTLE ASSY COMPLETE
120V (49 & 59 SERIES)
15-19 C3-49014 1 HANDLE AND ROD ASSY COMPLETE
2A-2100 1 PIN-GROOVE 1/80X5/8 ST
2A-Y5377 1 ROD-HANDLE-PLATED
2R-09-WB-0027 1 HANDLE BLACK 3/8-16
2B-Y6139 1 CLIP-HANDLE
2P-8880 1 SPRING-HANDLE TORSION
24 2V-Y5379 1 RETAINER
25 C3-Y5378 1 CAM
20-23 C3-59052 1 KETTLE CONDUIT W/WIRES
20 C3-59029 1 KETTLE LEAD WIRE ASSY
21 2P-8354 1 CAP-TWIST LOCK L5-15P
22 2E-8355 1 CONDUIT, FLEXIBLE - 14”
23
26
27 2C-2559 1 NUT 10-24 ACHD BR NP
31
2E-1177 1 CONNECTOR 3/8 TB#266
2K-3831 1 BUSHING-7/16 ODX-028
C3-59051 1 KETTLE SHELL ASSY OLD STYLE 49 & 59
2C-Y3166 1 WASHER
2C-1494 1 SCREW 8-32X1/2 RHP STL NP
2N-Y5592 1 ELEMENT 1420 WATTS/9.6 OHMS 120V
2N-Y5593 1 ELEMENT 1420 WATTS/40 OHMS 240V
Short Jumper
Long Jumper
Old Style Hinge Bracket = N/A
Use C3-Y2611 + C3-Y2612 instead
Short Jumper
Old Style Element Clamps = N/A
Use C3-Y3140 instead
Long Jumper
14 Oz. Kettle
89 Series
PARTS LIST EFFECTIVE 11-11-03 rb
MODEL 89 Series Machines
Key
Number
Part
Number
Number
Per
Unit
Description
14 Oz. Kettle Assembly
1-31 C3-89002 1 KETTLE ASSEMBLY COMPLETE - 120V (#8909159 & BELOW)
N/A - Use C3-89011 + C3-Y2612 instead
C3-89011 1 KETTLE ASSEMBLY COMPLETE - 120V (
(10 Lbs shipping weight)
C3-89009 1 KETTLE ASSEMBLY COMPLETE - 240V (#8909160 & ABOVE)
1 2F-8395 1 KETTLE CASTING (Sand Cast Material)
2 C3-8605 2 KETTLE JUMPER - LONG
3 2T-6213 2 THERMOSTAT (1/4 turn clockwise = 30
4 C3-8283 1 KETTLE HINGE BRACKET (#8909159 & BELOW)
N/A - Use C3-Y2611 + C3-Y2612 instead
C3-Y2611 1 KETTLE HINGE BRACKET (
5 2C-1589 2 MACHINE SCREW (1/4-20 x 1/2 Flat Head)
2C-Y1221 2 MACHINE SCREW (1/4-20 x 1/2 Hex Head)
6 C3-8690 2 KETTLE JUMPER - SHORT
7 C3-8568 1 THERMOSTAT CLAMP
8 2C-1810 9 BURR
9 2C-1512 7 SCREW (10-24 x 3/8)
10 C3-8951 1 THERMOSTAT CLAMP
11 2C-1515 2 SCREW (10-24 x 3/4)
13 C3-Y4053 1 KETTLE INSULATION
14 2C-8569 1 STUD (1/4-20 x 2)
#8909160 & ABOVE)
#8909160 & ABOVE)
0
F rise)
15-19, C3-59007 1 KETTLE HANDLE ASSEMBLY COMPLETE
24,25 (#8923059 & BELOW)
15 2P-8880 1 KETTLE HANDLE SPRING
16 C3-8838 1 KETTLE ROD HANDLE w/PIN
17 2R-8293 1 KETTLE HANDLE (wood)
18 2C-1811 1 BURR (1/4)
19 2C-2581 2 ACORN NUT (1/4-20)
24 2C-9607 1 SCREW - ADJUSTING
25 2A-5401 1 COTTER KEY
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
PAGE
1 OF 2
PARTS LIST EFFECTIVE 11-11-03 rb
MODEL 89 Series Machines
Key
Number
Part
Number
Number
Per
Unit
Description
14 Oz. Kettle Assembly
15-19, C3-49014 1 KETTLE HANDLE ASSEMBLY COMPLETE
24,25 (#8923060 & ABOVE)
2A-2100 1 PIN - GROOVE
2A-Y5377 1 KETTLE ROD HANDLE
2R-Y5375 1 KETTLE HANDLE
2C-Y5376 1 CLIP - LATCH HANDLE
2P-8880 1 KETTLE HANDLE SPRING
2V-Y5379 1 RETAINER / SPACER
C3-Y5378 1 CAM
20-23 C3-59052 1 KETTLE CONDUIT COMPLETE
20 C3-59029 1 KETTLE LEAD WIRE ASSEMBLY (2 wire set w/terminals)
2C-9617 2 WIRE TERMINAL
2I-5062 15 INSULATOR BEAD
21 2P-8354 1 MALE TWIST-LOC PLUG
22 C3-8355 1 KETTLE CONDUIT
C3-Y3045 1 GROUND STRAP
23 2E-1177 1 SQUEEZE CONNECTOR
2K-3831 1 BUSHING (for conduit)
(plastic)
(w/wires & twist-loc plug)
26 C3-59051 1 KETTLE SHELL W/WASHER
(#8923059 & BELOW) (needs C3-49014 HANDLE also)
2C-Y3166 1 WASHER (1” x 1/4”)
2C-1494 1 SCREW (holds shell to casting)
27 2C-2559 1 ACORN NUT (10-24)
28,29 C3-Y3140 2 NEW STYLE ELEMENT CLAMP (use qty. 3 each of Key #8 & #9)
8 2C-1810 3 BURR
9 2C-1512 3 SCREW
30 2N-Y5594 1 KETTLE ELEMENT - 120V (300W/ 40 ohms) (SMALL) (blue dot)
2N-Y5595 1 KETTLE ELEMENT - 240V (300W/ 40 ohms) (SMALL) (red dot)
31 2N-Y5592 1 KETTLE ELEMENT - 120V (1500W/ 9.6 ohms) (blue dot)
2N-Y5593 1 KETTLE ELEMENT - 240V (1500W/ 9.6 ohms) (red dot)
(Element design was changed in 6/87)
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED
INCLUDE MODEL AND SERIAL NUMBER
PAGE
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
2 OF 2
Hi-Temp Wire = 1N-E2052
Right Hinge w/Pin = C3-59019
Screw = 2C-1646
Left Hinge w/Pin = C3-59020
Screw = 2C-1646
Left Leaf Hinge Long = C3-8279
Screw = 2C-1512 (10-24x3/8)
Nut = 2C-2559
Motor Support Assy.
C3-59003
Right Leaf Hinge Long = C3-8278
Screw = 2C-1512 (10-24x3/8)
Nut = 2C-2559
New Style Hinge Bracket
C3-Y2612
PARTS LIST April 7, 2010,
8 oz. & 14 oz. Machines Parts
49, 59, 89 Series Machines
Key
Number
1 C3-Y6683 1 KETTLE & LID SUPPORT
2 C3-59011 1 RIGHT KETTLE LID ASSEMBLY W/HANDLE N/A - No replacement
2R-1272 1 KNOB - KETTLE LID
2C-1506 1 SCREW (not shown)
3 2P-Y6231 1 BEARING ASSEMBLY (PLASTIC)
4 C3-59012 1 LEFT KETTLE LID ASSEMBLY
5-13 C3-59053 1 KETTLE LATCH ASSEMBLY COMPLETE
5 C3-Y1470 1 KETTLE LATCH
6 C3-2806 1 KETTLE LATCH SPRING
7 2C-1505 2 SCREW (10-24x3/8)
2C-1827 2 WASHER-SHAKE (#10) (not shown)
8 2C-1557 1 SCREW (10-24x1-1/2)
9 2C-2559 2 ACORN NUT (10-24)
10 2C-2555 1 ACORN NUT (8-32)
11 2C-1493 1 SCREW (8-32x3/8)
2C-1825 1 WASHER-SHAKE (#8) (not shown)
12 C3-8313 1 KETTLE LID PIN SPRING
13 C3-2803 1 HINGE LATCH
14 C3-Y2612 1 KETTLE HINGE MOTOR HOUSING (#5909527 & UP)
15 2E-8343 1/3 SWITCH-TOGGLE (QTY.1 ON 59D & 89D ONLY for motor)
(QTY.3 ON #4942396, #5917564, #8926996 & ABOVE)
2E-Y6144 3 SWITCH-ROCKER (#4936951 TO #4942395) (not shown)
(#5916883 TO #5917563)
(#8923915 TO #8926995)
2E-3966 2 SWITCH-ROTARY (59D & 89D ONLY for kettle & lights) (not shown)
2R-7886 2 KNOB-ROTARY SWITCH (not shown)
16 C3-59004 1 MOTOR COVER ASSEMBLY
17 PS-49116 1 MOTOR W/GEAR BOX & LEAD WIRES (120V)
C3-59050 1 MOTOR W/GEAR BOX & LEAD WIRES (240V)
17a 2A-9556 NLA 1 MOTOR GEAR W/SHAFT (#5900 imprinted) (PLASTIC)
17b 2A-9557 1 MOTOR GEAR (#5318 imprinted) (METAL)
17c 2A-Y1265 1 MOTOR GEAR - SMALL (PLASTIC)
2I-H6579 4 MOTOR GROMMETS (not shown)
18 C3-8263 1 KETTLE HINGE PIN
19 2A-Y6694 1 HAIRPIN
(#4945475, #59118062, #8928211 & BELOW)
20 2A-7939 1 AGITATOR SHAFT
21 2A-Y1555 1 UNIVERSAL
22 2A-5401 1 COTTER PIN
23 2B-8317 4 AGITATOR BLADE (SPRING)(49 & 59 SERIES) (4” LONG)
2B-8319 4 AGITATOR BLADE (SPRING)(89 SERIES) (4-1/4” LONG)
24 C3-8318 1 AGITATOR COLLAR
25 2C-6170 2 SET SCREW (8-32)
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
Some items are included for illustrative purposes only and in certain instances may not be available.
Number
Part
MODEL
Number
Per
Unit
Description & Model Designation
1
4
Star International Holdings, Inc. Company
PARTS LIST April 7, 2010,
8 oz. & 14 oz. Machines Parts
49, 59, 89 Series Machines
Key
Number
20-25 C3-59057 1 AGITATOR ASSEMBLY COMPLETE (49 & 59 SERIES)
(TO UPDATE/UPGRADE - #4945475, #59118062 & BELOW)
20-25 C3-89006 1 AGITATOR ASSEMBLY COMPLETE (89 SERIES)
(TO UPDATE/UPGRADE - #8928211 & BELOW)
20 2A-Y7683 1 AGITATOR SHAFT (4-7/16” LONG)
20 2A-Y7217 1 AGITATOR SHAFT (5-7/16” LONG)
2C-Y6508 1 GROOVE - PIN (not shown)
21 2A-Y1555 1 UNIVERSAL
22 2A-Y6694 1 CLIP - SHAFT
23 2B-Y7218 1 AGITATOR BLADE (49 & 59 SERIES) (8-1/4” LONG)
2B-Y7219 1 AGITATOR BLADE (89 SERIES) (8-3/4” LONG)
24 2A-Y6207 1 AGITATOR COLLAR
25 2C-6170 2 SET SCREW (8-32)
20-25 C3-49502 1 AGITATOR ASSEMBLY COMPLETE (49 & 59 SERIES)
(#4945476, #59118063 & ABOVE) N/A-USE C3-59057 Instead
C3-89502 1 AGITATOR ASSEMBLY COMPLETE (89 SERIES)
(#8928212 & ABOVE) N/A-USE C3-89006 Instead
26 2S-Y2238 1 WARMER LAMP (120V, 250W)
2S-Y1508 1 WARMER LAMP - RED (120V, 250W) (used on 49D only)
27-29 C3-Y7940 1 CORN DRAWER ASSEMBLY (not as shown)
29 2R-4391 1 HANDLE
2R-Z0872 1 KNOB (not shown)
Number
Part
MODEL
Number
Per
Unit
Description & Model Designation
CUSTOMER’S VIEW, NOT SERVER’S
30-33 C3-49011 1 RIGHT DOOR COMPLETE (49)
C3-49052 1 RIGHT DOOR COMPLETE (49D) (#4905055 & BELOW)
N/A-No replacement
C3-49065 1 RIGHT DOOR COMPLETE (49D) (#4905056 & ABOVE)
C3-59069 1 RIGHT DOOR COMPLETE (59 & 89 SERIES, 89W) N/A-No replacement
30 C3-49068 2 DOOR HINGE ASSEMBLY-RIGHT (49D) (#4905056 & ABOVE)
C3-59054 2 DOOR HINGE ASSEMBLY-RIGHT
31 C3-Y2713 1 STRIKE - MAGNETIC LATCH
32 2R-1272 1 KNOB - DOOR (2C-1506 = SCREW)
33 C3-Y2730 2 DOOR - PLEXIGLASS (49) (15” x 9-1/2” W/2 holes)
C3-Y2979 2 DOOR - PLEXIGLASS (49D) (#4905056 & ABOVE)
(15” x 9-1/2” W/3 holes)
C3-Y2729 2 DOOR - PLEXIGLASS (59 & 89 SERIES, 89W)
(15” x 13” W/2 holes) N/A-No replacement
2M-Y1755 1 INSTRUCTIONS - CLEAR (not shown)
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
Some items are included for illustrative purposes only and in certain instances may not be available.
2
4
Star International Holdings, Inc. Company
PARTS LIST April 7, 2010,
8 oz. & 14 oz. Machines Parts
49, 59, 89 Series Machines
Key
Number
CUSTOMER’S VIEW, NOT SERVER’S
31-34 C3-49012 1 LEFT DOOR COMPLETE (49)
C3-49053 1 LEFT DOOR COMPLETE (49D) (#4905055 & BELOW)
N/A-No replacement
C3-49066 1 LEFT DOOR COMPLETE (49D) (#4905056 & ABOVE)
C3-59070 1 LEFT DOOR COMPLETE (59 & 89 SERIES, 89W)
N/A-No replacement
31 C3-Y2713 1 STRIKE - MAGNETIC LATCH
32 2R-1272 1 KNOB - DOOR (2C-1506 = SCREW)
34 C3-49069 2 DOOR HINGE ASSEMBLY-LEFT (49D) (#4905056 & ABOVE)
C3-59055 2 DOOR HINGE ASSEMBLY-LEFT
2M-Y1755 1 INSTRUCTIONS - CLEAR (not shown)
35,36 2Q-Y2608 3 GLASS (49 SERIES) (PURCHASE LOCALLY, if possible) (ALL SIDES)
(24-5/8 x 19-5/8 x 1/8 double strength)
35 2Q-8344 1 FRONT GLASS (59 & 89 SERIES, 89W)
(PURCHASE LOCALLY, if possible)
(26-5/8 x 24-5/8 x 1/8 double strength)
2Q-Y2912 1 FRONT GLASS (89T, TIFFANY)
2M-Y2737 1 SIGN - FRONT GLASS (89P, PATRIOT)
36 2Q-8345 2 SIDE GLASS (59 & 89 SERIES, 89W)
(PURCHASE LOCALLY, if possible)
(22-5/8 x 24-5/8 x 1/8 double strength)
2Q-Y2913 2 SIDE GLASS (89T, TIFFANY)
2M-Y2738 2 SIGN - SIDE GLASS (89P, PATRIOT)
37 2I-Z0160 6 GLASS CHANNEL (UPRIGHT) (Will need to be cut to 24-11/16”)
38 2I-Z0160 2 GLASS CHANNEL (SIDE, BOTTOM) (59 & 89 SERIES, 89W)
(Will need to be cut to 21-13/16”)
39 2I-Z0160 1 GLASS CHANNEL (FRONT, BOTTOM) (59 & 89 SERIES, 89W) (25-3/8”)
2I-Y2609 3 GLASS CHANNEL (BOTTOM) (49 SERIES)
40 C1-S7515 1 LEAD IN CORD - 120V (49 SERIES)
C3-49094 1 LEAD IN CORD - 240V (49 SERIES)
C3-59022 1 LEAD IN CORD - 120V (59 SERIES)
C3-89008 1 LEAD IN CORD - 120V (89 SERIES)
C3-59023 1 LEAD IN CORD - 240V (59 & 89)
C3-89001 1 LEAD IN CORD - 120V (59D, 59SL, 89D, 89SL)
C3-59036 1 LEAD IN CORD - 240V (59D, 59SL, 89D, 89SL)
2K-Y2968 1 BUSHING - STRAIN RELIEF (120V)
2K-Y2967 1 BUSHING - STRAIN RELIEF (240V)
2E-8715 1 FEMALE WALL RECEPTACLE (120V only)
41 C3-49003 1 TOP ASSEMBLY (49) N/A-No replacement
C3-49054 1 TOP ASSEMBLY (49D, #4905055 & BELOW)
C3-49067 1 TOP ASSEMBLY (49D, #4905056 & ABOVE)
C3-59014 1 TOP ASSEMBLY (59 & 89) N/A-No replacement
C3-59015 1 TOP ASSEMBLY (59D & 89D) (less sign) N/A-No replacement
C3-59110 1 TOP ASSEMBLY (89SL)
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
Some items are included for illustrative purposes only and in certain instances may not be available.
Number
Part
MODEL
Number
Per
Unit
Description & Model Designation
3
4
Star International Holdings, Inc. Company
PARTS LIST April 7, 2010,
8 oz. & 14 oz. Machines Parts
49, 59, 89 Series Machines
Key
Number
42,43 2C-9788 1 MAGNET & BRACE
44 2E-T1042 1 FEMALE TWIST LOCK RECEPTACLE
45 C3-59035 1 PILOT LIGHT ASSEMBLY - 120V (49, 59, 89, 89W )
C3-59034 1 PILOT LIGHT ASSEMBLY - 240V (49, 59, 89 )
C3-59047 1 PILOT LIGHT ASSEMBLY - 120V (49D, 59D, 89D)
C3-59048 1 PILOT LIGHT ASSEMBLY - 240V (49D, 59D, 89 D) N/A-No replacement
46 2E-Y5921 1 SOCKET - LAMP
C3-Y6129 1 CLIP
C3-Y4526 1 LAMPSHIELD (49 & 59 SERIES)
C3-Y4122 1 LAMPSHIELD (89 SERIES)
47 C3-8725 1 COVER - CONTROL (59, 89) (not shown)
C3-8386 1 COVER - CONTROL (59D, 89D) (not shown)
C3-Y2614 1 COVER - CONTROL (49 SERIES) (not shown) (alias SWITCHPLATE)
48 C3-49106 1 FRONT LOWER DOOR ASSEMBLY (49 SERIES)
C3-59106 1 FRONT LOWER DOOR ASSEMBLY (59 & 89 SERIES)
C3-89058 1 FRONT LOWER DOOR ASSEMBLY (89W)
2A-Y3405 4 FOOT
2M-Y6459 1 DECAL “FRESH POPPED POPCORN” (59, 89) N/A-No replacement
2M-Y2632 1 DECAL - SWITCHES, “KETTLE & WARMER”
2M-Y6306 1 DISPLAY SIGN (49SL) (back) N/A-No replacement
2M-Y6307 1 DISPLAY SIGN (49SL) (front) N/A-No replacement
2M-8506 1 DISPLAY SIGN (59D, 89D) N/A-No replacement
2M-Y6453 1 DISPLAY SIGN (49)
C3-Y2721 1 DISPLAY SIGN (49D) (woodgrain design) N/A-No replacement
2M-Y2062 1 DISPLAY SIGN (89W)
2M-Y6460 2 DISPLAY SIGN (89SL) N/A-No replacement
2S-8373 2 DISPLAY LAMP (59D, 89D) N/A-No replacement
C3-Y2722 1 RETAINER BOTTOM (for sign)
2N-8396 1 WARMER ELEMENT - 120V (not shown)
2N-8397 1 WARMER ELEMENT - 240V (not shown)
C3-8334 1 CORN SCOOP - METAL (not shown)
2L-Y4640 1 CORN CUP (3/4 cup) (not shown)
2L-Y4639 1 OIL CUP (1/4 cup) (not shown)
Part
Number
MODEL
Number
Per
Unit
Description & Model Designation
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
Some items are included for illustrative purposes only and in certain instances may not be available.
Star International Holdings, Inc. Company
4
4
Loading...