Star Manufacturing GR14SPTA-UK Operation Manual

®
®
®
®
SPLIT LID TABLE TOP
®
TWO SIDED GRILL
MODEL
GR14SPTA-UK
Installation and
Instructions
2M-Z7273 Rev. F 11/18/09
GR14SPTA
1
2
These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability.
Star reserves the right to change specifi cations and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.
Due to periodic changes in designs, methods, procedures, policies and regulations, the specifi cations contained in this sheet are subject to change without notice. While Star Manufacturing exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the specifi cations. By using the information provided, the user assumes all risks in connection with such use.
MAINTENANCE AND REPAIRS
Contact your local dealer for service or required maintenance. Please record the model number, serial number, voltage and purchase date in the area below and have it ready when you call to ensure a faster
service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
2
GENERAL INSTALLATION DATA
CAUTION
This equipment is designed and sold for commercial use only by personnel trained and experienced in its operation and is not sold for consumer use in and around the home nor for use directly by the general public in food service locations.
INSTALLATION
1. Plug the unit into a dedicated 230 VAC line with United Kingdom BS 1363A receptacle.
2. DO NOT plug into a
3. Each machine has been properly wired and inspected at the factory for operation on the voltage
and type of current specied on the nameplate.
4.
IEC Plug & Cord are NOT included with this unit.
WARNING
DO NOT CONNECT TO ANY TYPE OF CURRENT OTHER THAN 230 VAC OR THE MACHINE WILL BE SERIOUSLY DAMAGED.
INITIAL START UP
Before using the unit for the rst time, clean and heat for approximately 45 minutes.
PRESET TIMES AND TEMPERATURES
If adjustments are required, please refer to the time or temperature programming section in this manual.
120V line. Doing so will damage the unit and void the warranty.
°F/°C CONVERSION
To change the temperature display from °F to °C or from °C to °F, hold the TEMP button while the unit is turned off. While holding the TEMP button, turn the unit on. The display will be the changed temperature mode. To change back, repeat the procedure.
OPERATING INSTRUCTIONS
1. Turn the unit on by placing the switch in the ON position. The HEAT ON indicator, program number and display will ash indicating the unit is heating. When the preset temperature is reached, the heating light, display and program light indicator will stop ashing followed by 3 beeps. (Initial
startup heating time is approximately 30 minutes).
2. Place product on the bottom cooking surface of the unit and close the lids.
3. Press the PROGRAM button and let the displayed time count down to "0" at which time the unit will beep. To turn off the beeper, press the PROGRAM button again.
4.
Raise the lid until it engages into the rst detent and remove food. Using a spatula, scrape residue
into the grease catcher tray.
NOTE:
cooking surface.
5.
Turn the unit off when it is not in use.
TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS Startup:
1. The preset time will ash until the preset temperature is reached.
2. When the control reaches the preset temperature, time display, the HEAT ON indicator and program indicator will stop ashing and the alarm will beep three times.
Metal utensils may be used, however, using nonmetal utensils will prolong the life of the
Temperature:
1. To view the actual temperature, press and hold the TEMP button. The display will read "Lo" if the temperature is below 273°F (135°C) and "Hi" if the temperature is above 573°F (300°C).
3
To Program Time and Temperature:
1. Press and hold TEMP (actual temperature displays).
2. While holding TEMP, press and hold any program button on the left for one second. The LED above
the program number will light and the display will read "_ _ _ _." Enter the four-digit security code
sequence: 4, 3, 2, 1. The security code will not show on the display. Once the correct sequence has
been entered, the preset time will be displayed and the LED for that program will begin to ash.
3.
Set the time with the "+ or -" buttons.
4. Press the TEMP button to save the time.
5.
The preset temperature will now be displayed.
6. Set the desired temperature for this program using the "+ or -" buttons.
7.
Press the TEMP button to save the temperature and to exit the programming mode for this program.
The LED will stop ashing but will remain lit.
8.
Press any other program button within 15 seconds to continue programming without re-entering the
security code.
9.
While programming a program (LED is ashing), if no input is received for 15 seconds the unit will
revert to normal operation and the security code must be re-entered.
NOTE: Temperature settings are done with the Left side buttons only. The time settings programmed on the left buttons will also be programmed onto the Right side. See the next section to make time changes to the Right side only.
Each programming change must be saved by pressing the TEMP button!
Right Side (Timer only):
1. To change the time on right, press and hold the TEMP button, then press and hold any program button
on the right for one second. The LED above the program button will light and the right display will
read "_ _ _ _." Enter the four-digit security code sequence: 4, 3, 2, 1. The security code will not
show on display. Once the correct sequence has been entered, the preset time will be displayed and the LED for that program will begin to ash.
2. Set the time with the "+ or -" buttons. 3
. Press the TEMP button to save the time.
4.
The LED will stop ashing but will remain lit.
5. Press any other program button within 15 seconds to continue programming without re-entering the
security code.
6.
While programming a program (LED is ashing), if no input is received for 15 seconds the unit will
revert to normal operation and the security code must be re-entered.
Operation:
1. Pressing any program button (1-4) will start the timer countdown and display the remaining preset time. The LED for the appropriate program will be lit during the countdown and will remain lit until
another program is selected.
2. When the display reaches "00:00", the buzzer will sound and the digits will ash.
3. Press the program button to silence the buzzer and return the readout to programmed time.
4. The right and left sides will operate independently of each other. Both timers can be in operation
at the same time. The "00:00" display will show which side is timed out.
4
Loading...
+ 8 hidden pages