Star Manufacturing GR14SPT Installation Manual

®

SPLIT LID TABLE TOP

TWO SIDED TOASTER

MODEL

GR14SPT-240V

Installation and

Operation

Instructions

2M-Z4319 Rev. C 9/29/06

GR14SPT

1

SAFETY SYMBOL

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specifi cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifi cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specifi cations. By using the information provided, the user assumes all risks in
connection with such use.

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record the model
number, serial number, voltage and purchase date in the area below and have it ready when you call to

ensure a faster service.

Model No.

Serial No.

Voltage

Purchase Date

Authorized Service Agent

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

The Star Service Help Desk

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone] Local [phone]

Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

2

GENERAL INSTALLATION DATA

CAUTION

This equipment is designed and sold for commercial use only by personnel trained and
experienced in its operation and is not sold for consumer use in and around the home nor for
use directly by the general public in food service locations.

INSTALLATION

1. Plug unit into dedicated 240 V.A.C. line with 15AMP receptacle.
2, DO NOT plug into 120V line. Doing so will damage the unit and void the warranty.

3. Each machine has been properly wired and inspected at the factory for operation on the
voltage and type of current specifi ed on the nameplate.

DO NOT CONNECT TO ANY TYPE OF CURRENT OTHER THAN 240 V.A.C. OR THE
MACHINE WILL BE SERIOUSLY DAMAGED.

CAUTION

INITIAL START UP

Before using the unit for the fi rst time, clean and heat for approximately 45 minutes.

DO NOT ADJUST TIME AND TEMPERATURE
The unit time and temperature is preset by the factory to the specifi c customer requirements
for fl atbread, burritos, quesadillas and cleaning.

The preset time and temperatures are:

Left Display:

Button Number Time Temperature
1 15sec. 505°F
2 27sec. 505°F
3 35sec. 505°F
4 (Cleaning) 00sec. 275°F

If adjustments are required for additional food products, please refer to the time or
temperature programming section in this manual.

OPERATING INSTRUCTIONS

1. Turn unit on by placing switch in "ON" position. The "Heat On" indicator, program
number and display will fl ash indicating unit is heating. When the preset temperature is
reached, the heating light, display and program light indicator will stop fl ashing followed by 3
beeps. (Initial startup heating time is approximately 30 minutes).
2 Place product on the bottom cooking surface of the unit and close the lids.

3. Press program button and let displayed time count down to "0" at which time unit will
beep. To turn off the beeper, press program button again.

4. Raise lids until it engages into fi rst detent and remove food. Using spatula, scrape residue
into grease catcher tray.
Note: Metal utensils may be used, however, using nonmetal utensils will prolong the life of
the cooking surface.

5. Turn the unit off when not in use.

Right Display:

Button Number Time Temperature
1 15sec. Same as Left
2 27sec. Same as Left
3 35sec. Same as Left
4 00sec. Same as Left

3

TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS

Startup:

1. The preset time will fl ash until preset temperature is reached.

2. When the control reaches preset temperature, time display, "Heat On" indicator and
program indicator will stop fl ashing and the alarm will beep three times.

Temperature:

1. To view the actual temperature, press and hold "Temp Button". Display will read "Lo F" if
temperature is below 273°F and "Hi F" if temperature is above 573°F.

To Program Time and Temperature:

1. Press and hold "TEMP" (actual temperature displays).

2. While holding "TEMP", press and hold any program button on the Left one second, the
LED above the program number light and the display reads "_ _ _ _". Enter the four - digit
security code sequence, 4, 3, 2, 1. The security code will not show on display. Once the
correct sequence has been entered, the preset time will be displayed and the LED for that
program will begin to fl ash.

3. Set the time with the "+ or -" buttons.

4. Press the "TEMP" button to save the time.

5. The preset temperature will now be displayed.

6. Set the desired temperature for this program using the "+ or -" buttons.

7. Press the "TEMP" button to save temperature and to exit programming mode
for this program. The LED will stop fl ashing but will remain lit.

2. Press any other program button within 15 seconds to continue programming without re­ entering the security code.

3. While programming a program (LED is fl ashing), if no input is received for 15 seconds,
the unit will revert to normal operation and the security code must be re-entered.

Note: Temperature settings are done with the Left side buttons only. The time settings
programmed on the Left buttons will also be programmed onto the Right side. See below to
make time changes to the Right side only. Each programming change must be saved by

pressing the "TEMP" button!

Right Side (Timer only):

1. To Change the time on Right, press and hold the "TEMP" button, and press and hold any
program button on the Right for one second. The LED above the program button will light
and the Right Display will read "_ _ _ _".
Enter the four-digit security code sequence, 4, 3, 2, 1. The security code will not show on
display. Once the correct sequence has been entered, the preset time will be displayed
and the LED for that program will begin to fl ash.

2. Set the time with the "+ or -" buttons.

3. Press the "TEMP" button to save the time.

4. The LED will stop fl ashing but will remain lit.

5. Press any other program button within 15 seconds to continue programming without
re-entering the security code.

6. While programming a program (LED is fl ashing), if no input is received for 15 seconds,
the unit will revert to normal operation and the security code must be re-entered.

Operation:

1. Pressing any program button (1-4) will start the timer countdown and display the preset
time remaining. The LED for the appropriate program will be lit during countdown and
remain lit until another program is selected.

2. When the display reaches "00:00", the buzzer will sound and the digits will fl ash.

3. Press the program button to silence the buzzer and return the readout to programmed
time.

4. The Right and Left sides will operate independent of each other. Both timers can be in
operation at the same time. The "00:00" display will show which side is timed out.

4