Star Manufacturing GPC-14 Installation Manual

®

®

®

®

®

POPCORN

CARTS

MODELS

GPC-8

GPC-8AT

GPC-14

GPC-14AT

Installation and

Operation

Instructions

2M-Y8652 Rev. D 7/14/05

G14-AT

1

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change speci cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and
regulations, the speci cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
speci cations. By using the information provided, the user assumes all risks in
connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record
the model number, serial number, voltage and purchase date in the area below and have it

ready when you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone] Local [phone]

Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

The Star Service Help Desk

Authorized Service Agent

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

INSPECTION & ASSEMBLY

UNCRATING & INSPECTING

Carefully unpack the unit and inspect it for any damage.

Check the parts against the attached parts list before starting any assembly. Refer to
drawing SK1246 for exploded view of cart.

CART HANDLE ASSEMBLY
(see SK1245)

Assemble left and right handle brackets (#6 & 7) to handle rod (#8) using (2) 1/4"-20x3/8"
machine screws (#11a) and (2) 1/4" lockwashers (11c).

NOTE: 90

Mount completed handle assembly to cart body (#1) using (4) 1/4-20x3/8 machine screws
(11a), (4) 1/4" lockwashers (#11c) and (4) 1/4-20 acorn nuts (#11b).

LEG ASSEMBLY

Insert one end of tie rod assembly (#10) through hole in side of (1) support leg (#9) and lock
in position with (1) 5/16" push nut (#11h).

Repeat above step for opposite leg.

CAUTION

DAMAGE MAY OCCUR TO PUSH NUTS IF REMOVAL IS ATTEMPTED

AFTER THEY ARE IN POSITION.

o

anges should be turned to the inside (facing each other).

LEG AND WHEEL ASSEMBLY (TO BODY)

Install completed leg assembly to the bottom of the body assembly (#1) with (4) 1/4-20x3/8
machine screws (#11a) and (4) 1/4" lockwashers (#11c). Install (2) axle support brackets
(#4) to the bottom of the body assembly (#1) with (8) 1/4-20x3/8" machine screws (#11a)

and (8) 1/4" lockwashers (#11c).

Insert axle (#3) through both axle support brackets. Insert (1) 3/32x3/4" cotter pin (#11f)
through hole near each end of the axle rod and spread cotter pin legs to prevent loss of
cotter pin.

NOTE: Cotter pins should be on the inboard side of each axle bracket.

Install (1) axle sleeve (#11d) followed by (1) 1/2" at washer (#11e) to each end of axle rod.

Install (1) wheel (#2) followed by (1) 1/2-13 locknut (#11g) to each end of axle rod.

NOTE: Grip axle rod with vise grips, channel lock pliers or pipe wrench near inboard
side of axle rod support since any marking of paint or plating will be hidden by the
bracket.

DROP SHELF INSTALLATION

Assemble drop shelf assembly (#5) to body (current construction level) using (4) 1/4-20x3/8"
machine screws (#11a), (4) 1/4 lockwashers (#11c) and (4) 1/4-20 acorn nuts (#11b).
Adjustment can be made left or right, up or down before nuts are fully tightened.

3