Star Manufacturing GPB-14 Parts List

Star
Manufacturing
International Inc.

10 Sunnen Drive
St. Louis, MO 63143

Phone: [phone]

2M-Y8653 Rev. C 3/19/03

Fax: [phone]

Installation

and

Operating

Instructions

GALAXY POPCORN BASES

MODELS

GPB-8, GPB-8AT, GPB-14, GPB-14AT

1

SAFETY SYMBOL

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change speci cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and
regulations, the speci cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
speci cations. By using the information provided, the user assumes all risks in
connection with such use.

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record
the model number, serial number, voltage and purchase date in the area below and have it

ready when you call to ensure a faster service.

Model No.

Serial No.

Voltage

Purchase Date

Authorized Service Agent

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

The Star Service Help Desk

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone] Local [phone]

Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

2

Carefully unpack the unit and inspect it for any damage.

Check the parts against the attached parts list before starting any assembly. Refer to draw­ing SK1247 for exploded view of base.

Assemble drop shelf assembly (#2) to body (#1) using (4) 1/4"-20 x 3/8" machine screws
(#3a), (4) 1/4" lockwashers (#3c) and (4) 1/4-20 acorn nuts (#3b). Adjustment can be made
left or right and up or down before nuts are fully tightened.

INSTALLATION OF MACHINE TO BASE

PREPARATION

Remove kettle from popcorn machine and set it aside out of the way.

Carefully lay the popcorn machine down on its back or sides, on a smooth, fl at surface.

NOTE: You may want an assistant for this step.

CAUTION

DO NOT LAY THE POPCORN UNIT ON THE DOORS OR ON AN OBSTRUCTED
OR UNEVEN SURFACE AS GLASS BREAKAGE MAY OCCUR.

Remove the (4) rubber plugs from the phenolic feet. Using a phillips screwdriver, remove (1)
screw from each foot and replace it with a 10-24x2" collared stud (#3d) in the same position
(see SK1247).

NOTE: Approximately 3/8" of thread will protrude from the bottom of each foot.

INSTALLATION

Using an assistant, raise the popper to its upright position. Use caution not to bend or dam­age the threaded studs.

Move base close to the popper with the open shelves facing in the same direction as the
doors on the popper.

Place the sleeve bushing (#3g) into the black plastic bushing on the top panel of the base.

Lace cord set through the sleeve and bushing from top to bottom as far as it will go.

With your assistant's help, carefully pick up the popcorn machine from the bottom. DO NOT
pick up the machine by grasping the doors, top or other "convenient" hand holds. NON
STRUCTURAL PARTS MAY BE DAMAGED. Place the popcorn machine on the base with
the (4) studs near the mounting holes in the top plate of the base. Be careful not to pinch
your hand or fi ngers between the two units.

NOTE: Placing the popper slightly askew (catty corner) will provide clearance for your
hands.

Carefully slide the popper into position on the base until the (4) studs drop through the
mounting holes in the top plate. Do not allow the popper to drop too heavily, try to ease it
into position one stud at a time. KEEP FINGERS CLEAR.

Place (1) fl atwasher (#3f) and (1) 10-24 acorn nut (#3e) on each stud protruding through the
top plate of the base and tighten.

Replace the kettle assembly, plug in the unit and check for proper operation.

This completes the installation procedure. Occasionally check the mounting nuts since
movement may cause them to loosen. Re-tighten as necessary.

MAINTENANCE AND REPAIRS

Contact the factory, a service representative or a local service company for service or re­quired maintenan

3