Star Manufacturing FS1R, FS1D, FS1RT, FS1DT, FS2R Operation Manual

FAST

STEAMER

MODEL

FS1R, FS1D, FS1RT, FS1DT
FS2R, FS2D, FS2RT, FS2DT

FSFR, FSFD, FSFRT, FSFDT

Installation and

Operation

Instructions

2M-Z10887 Rev. E 7/27/2009

FS2DT

FSFRT

1

2

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specifi cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifi cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specifi cations. By using the information provided, the user assumes all risks in
connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record the model
number, serial number, voltage and purchase date in the area below and have it ready when you call to

ensure faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone] Local [phone]
Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

The Star Service Help Desk

Authorized Service Agent

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

SPECIFICATIONS

A

C

B

A

C

B

FRONT LOADING TOP LOADING

IL1361

FAST STEAMERS SPECIFICATIONS

FRONT LOADING

Model "A" Width "B" Height "C" Depth Approx. Capacity (inches) Direct (D)
No. Inches/CM Inches/CM Inches/CM Shp Weight W_x_D_x_H Reservoir (R)

FSFR 23in. / 58.4cm 9.5in / 24.1c, 21.5in / 54.4cm 48lbs / 21.8kg 13.75" x 13.75" x 3" R
FSFD 23in. / 58.4cm 9.5in / 24.1c, 21.5in / 54.4cm 48lbs / 21.8kg 13.75" x 13.75" x 3" D
FSFRT 23in. / 58.4cm 9.5in / 24.1c, 21.5in / 54.4cm 48lbs / 21.8kg 13.75" x 13.75" x 3" R
FSFDT 23in. / 58.4cm 9.5in / 24.1c, 21.5in / 54.4cm 48lbs / 21.8kg 13.75" x 13.75" x 3" D

TOP LOADING Pan Size

FS1R 18.8in / 47.8cm 10.5in / 26.7cm 17.2in / 43.7cm 48lbs / 21.8kg 1/2 R
FS1D 18.8in / 47.8cm 10.5in / 26.7cm 17.2in / 43.7cm 48lbs / 21.8kg 1/2 D
FS1RT 18.8in / 47.8cm 10.5in / 26.7cm 17.2in / 43.7cm 48lbs / 21.8kg 1/2 R
FS1DT 18.8in / 47.8cm 10.5in / 26.7cm 17.2in / 43.7cm 48lbs / 21.8kg 1/2 D
FS2R 22.4in / 56.9cm 10.5in / 26.7cm 17.2in / 43.7cm 58lbs / 26.4kg 2/3 R
FS2D 22.4in / 56.9cm 10.5in / 26.7cm 17.2in / 43.7cm 58lbs / 26.4kg 2/3 D
FS2RT 22.4in / 56.9cm 10.5in / 26.7cm 17.2in / 43.7cm 58lbs / 26.4kg 2/3 R
FS2DT 22.4in / 56.9cm 10.5in / 26.7cm 17.2in / 43.7cm 58lbs / 26.4kg 2/3 D

ELECTRICAL SPECIFICATIONS

 FrontLoading     Certication

Model No. Voltage Wattage Amps Nema Plug UL CUL

FSF 208V 3,300 15.9 6-20P X X
FSF 240V 3,600 15.0 6-20P X X

Top Loading

Model No. Voltage Wattage Amps Nema Plug

FS1/FS2 120V 1,800 15.0 5-15P X ­ FS1/FS2 120VC 1,800 15.0 5-20P X X

3

GENERAL INFORMATION

CAUTION

This equipment is designed and sold for commercial use only by personnel trained and experienced in
its operation and is not sold for consumer use in and around the home nor for use directly by the general
public in food service locations.

Before using your new equipment read and understand all the instructions & labels associated with the
unit prior to putting it into operation. Make sure all people associated with its use understand the units
operation & safety before they use the unit.

All shipping containers should be checked for freight damage both visible and concealed. This unit has
been tested and carefully packaged to insure delivery of your unit in perfect condition. If equipment is
received in damaged condition, either apparent or concealed, a claim must be made with the delivering
carrier.

Concealed damage
request for inspection of concealed damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials for inspection. The carrier will make
an inspection and will supply necessary claim forms.

These models are equipped for the voltage and wattage indicated on the nameplate. These units are
designed to operate on alternating current (A.C.), two wire single phase service only and are equipped
with an approved lead in cord set with a three prong grounding type plug.

or loss - if damage or loss is not apparent until after equipment is unpacked, a

DO NOT CONNECT TO DIRECT CURRENT (D.C.).

UNPACKING

Carefully remove the steamer from the shipping and packing & protective material. Remove all removable
parts and clean with hot water and mild detergent. Wipe the unit using damp cloth. Never hose down
the unit with water, this steamer has

Unit should also contain:

• Operations manual & Authorized Service Agent Listing Packet

• Inlet Hose Assembly (non-reservoir units only)

• Spatula tray (front loading units only)

Purchasers Responsibility

• To see that the electric & water services for the unit are installed on site in accordance with

the manufacturer's specications and municipal codes.

• A water pressure regulator must be used, failure to operate this unit without a regulator will
result in situations that will damage the unit.

4

INSTALLATION

ELECTRICAL CONNECTION

For your protection, we recommend that a qualified electrician install this appliance.
The electrician should be familiar with electrical installations and your local electrical requirements.

Proper connections and power supply are essential for efcient performance. The supply circuit should

be properly fused as required by local electrical code.

WARNING

Before making any electrical connection be sure to read data plate which is located on the
rear of the unit.

Electrical Grounding Instructions

This unit is equipped with a 3-prong (grounded) plug for your protection against shock hazard and must
be plugged directly into a properly grounded 3-prong receptacle.

CAUTION

DO NOT CUT OR REMOVE THIS PLUG OR GROUNDED PRONG FROM THE PLUG.
CONNECT/PLUG UNIT INTO DEDICATED A.C. LINE ONLY SPECIFIED ON THE DATA

PLATE OF THE UNIT.

PRESET TIME

If adjustments are required, please refer to the time programming section in this manual.

°F/°C CONVERSION

To change the temperature display from °F to °C or from °C to °F, hold the TEMP button while the unit is
turned off. While holding the TEMP button, turn the unit on. The display will be the changed temperature
mode. To change back, repeat the procedure.

5

INSTALLATION continued

Filter

Regulator

To Steamer

Guage

Water

Source

26 psi

IL1532

Lid

Strainer

Water Inlet

IL1537

WATER CONNECTION

These units come equipped with either a direct connect, rear mounted quick disconnect uid control

valve, or a 12 cup water tank with tank drain and supply pump. It is vital that all water supply lines be

thoroughly ushed with clean water before being connected to the steamer.

The Star Fast-Steamer has a water injection system, to ensure your new equipment works at its premium,
we recommend that a water softener is used in areas where hard water is present. Contact your local

water equipment system provider to assist you in determining your specic water quality, or contact Star

Technical

support for assistance, 1-800-807-9054.

Direct Connect Water Supply Installation

1. Make certain the water valve that
will be suppling the unit is turned
off.

2. Connect the 1/4" I.D. exible
tubing
source and secure with clamps
provided.

3. Holding the end opposite end
over

(this removes any air from the system and ushes it of any particles that may be present).

4. Turn off the water valve.

5. Push the check valve tting into the water inlet located on the rear of the unit.

Make

6. Turn on water valve, Turn the knob on the regulator until the guage reads 26 psi.
Check

to the outlet side of the water

a bucket, turn the water valve on until there is a good consistent supply of water

certain the connection is securely attached by lightly tugging on it.

for leaks.

Reservoir Water Units

1. With unit in nal position, open reservoir lid.

2. Check and make sure the reservoir is free of debris
and material that may interfere with its operation.

3. The unit comes with a washer strainer which ts

over the water inlet

(see illustration),
correctly in position. Periodically check strainer and
clean and replace as often as necessary.

4. Pour tap water into reservoir until the water level is
from the top.

1/4"

5. Closed lid.

6. Check water level during daily operation and ll as needed.

verify this is

6

OPERATING PROCEDURE

Connect your unit to a wall outlet which will supply the unit with the proper voltage specied on the data

plate. If you have a reservoir unit, verify the water level, add if water is low.

CAUTION

KEEP HANDS AND FACE AWAY FROM THE UNIT WHEN OPENING OR REMOVING THE
SPATULA FROM THE UNIT. STEAM ESCAPING IS VERY HOT.

MANUAL CONTROL

• Turn unit on

Wait 20 - 30 minutes for the unit to reach its operating temperature before using.

Note: The Temperature Set Point is factory xed at 400°F (204°C) and is not adjustable.

•

Place product in cooking chamber and hit the Steam Shot button to steam the product.

Steam Shot: Pressing the Green Steam Shot Green Button will release water in to the steam generator

and will instantly produce steam. Water will only stop when the button is released. Flooding of the
steam generator may occur if the Steam Shot button, or the SST is set to high. When this occurs wait
for the unit to work through the water before applying more water

to the steam generator.

ELECTRONIC CONTROL

• Turn unit on

Current Temperature will Flash on LED, PRESS the

TEMP button to see current temperature
TCT will FLASH until TSP (Temperature Set Point) is reached,
Alarm will sound 3-times when TSP is reached.

Note: The Temperature Set Point is factory xed at 400°F (204°C) and is not adjustable.

•

Place product in cooking chamber and choose one of the 4 pre-determined programmed

settings, or hit

• When program timing is completed, an alarm will sound.

the Steam Shot steam button to steam the product.

PROGRAMMING DEFINITIONS

TCT Total Cook Time
SIT Shot Interval Time
SST Steam Shot Time
TSP Temp Set Point

Steam Shot: Pressing the Green Steam Shot Button will release water in to the steam generator and

will instantly produce steam. Water will only stop when the button is released. Flooding of the steam
generator may occur if the Steam Shot button, or the SST is set to high. When this occurs wait for the

unit to vaporize all of the water before applying more water to the steam generator.

TIMER & STEAMER CONTROLLER OPERATION SPECIFICATIONS
Startup:

1. The preset time will ash until the operating temperature is reached.

2. When the control reaches preset temperature, time display, "Heat On" indicator and program

indicator will stop ashing and the alarm will beep three times.

Temperature:

1. To view the actual steam generator temperature, press and hold "Temp Button."

7

OPERATION continued

90 degrees

60 degrees

Cover

Stop

IL1366

To Program Time:

The program buttons factory pre-set are listed
below. If changes are required follow these
simple steps. Note, any changes to these

PROGRAMMING SPECIFICATIONS / RANGE

TCT Total Cook T
SIT Shot Interval Time .5sec to 10 minutes
SST Steam Shot Time .1 sec to 5.minutes
TSP Temp Set Point

settings are stored in the units memory until
changed. Returning to the factory pre-sets is not

available automatically.

1. Press and hold "TEMP"

(actual temperature displays).

2. While holding "TEMP,"

program button for one second, to begin

press and hold any

TCT 20 sec 40 sec 1 min 1.30 min

SIT 20

SST .5

programming

3. TCT (Total Cook Time) will

display, adjust

time with the "3 or 4" buttons.

• Press the #1 button to move to between minutes and seconds.

• Press the #1 button to move to SIT.

4. SIT

(Shot Interval Time) will

display, adjust time with the "3 or 4" buttons.

• Press the #1 button to move to between minutes and seconds.

• Press the #1 button to move to SST.

5. SST

(Steam

Shot Time) will display, adjust time with the "3 or 4" buttons.

ime 0 to 99.59 minutes

Program Button Factory Presets

1 2 3 4

sec 40 sec 40 sec 40 sec

sec .5 sec .5 sec .5 sec

• Press the #1 button to move to seconds.

6. Press

the "TEMP" button

to save time settings and to exit programming mode for this

program. Your program will not be saved if this step is not done within 10 seconds.

7. Repeat

process to program for additional programming

Hi-Limit Reset

A hi-limit reset monitors the temperature of the steam generator and will turn the power off to the unit to
prevent it from overheating. If this occurs, the unit will automatically reset when it has had enough time to
cool prior to returning to operation. If this occurs on a regular basis it may be a sign of a larger problem, call

your service agent or Star Manufacturing at

1-800-807-9054.

TOP LOADING COVER STOP

SETTINGS

Top Loading Fast Steamer models

(FS1 & FS2) are designed with

adjustable cover stops located on

the back of the units. As shown

here you can adjust your unit's

top cover between an opening

of 60° - 90°.

8

CLEANING

CAUTION

DO NOT USE CAUSTIC CLEANERS,
USE A MILD DETERGENT TO WIPE DOWN EXTERIOR SURFACES, CLEAN WITH DAMP

CLOTH

Daily

1. Turn the unit OFF & unplug the unit from its power source before proceeding with any service

or cleaning procedure.

2. Remove and clean the removable items listed on the maintenance components illustration for

your specic model. Clean using warm water and mild detergent. DRY parts completely

3. Wipe the exterior or the steamer with a damp cloth, then wipe dry. Note: drying all pieces

after cleaning will protect your nish from discoloration, any discoloration as a result from not

drying the equipment is not covered under warranty

4. Reinstall

the unit, beginning with the Steam Vent.

Monthly

The Star Fast Steamer generates instant steam by means of its open generator, however the mineral
deposits in the water are left behind. A certain amount of deposits are needed for proper operation, but a
build-up of calcium & mineral deposits may cause poor performance. It is important to properly maintain

you steamer to ensure quality operation. Depending on your specic water conditions and possibly any
water ltration systems, you may need to clean your steamer more or less frequently.

.

CAUTION

DO NOT IMMERSE OR LET THE UNIT STAND IN WATER. DO NOT HOSE DOWN
THE UNIT. KEEP THE UNIT AWAY FROM RUNNING WATER.

DO NOT SPLASH THE CONTROL HOUSING
CERTAIN WATER CONDITIONS MAY REQUIRE MORE FREQUENT CLEANING.

WARNING

BEFORE CLEANING MAKE SURE POWER IS TURNED OFF AND UNIT IS
UNPLUGGED.

CAUTION

IF A CHEMICAL CLEANER / DELIMER IS USED, BE CERTAIN IS IT SAFE FOR CAST
ALUMINUM. FOLLOW PROCEDURES, PRECAUTIONS PROVIDED WITH THAT SPECIFIC
PRODUCT.

9

Cleaning Steam Generator

Steam Generator

Steam Ports

Water Inlet

IL1359

Wing Nut
Generator

Cover

Diffuser

IL1377

1. Turn the unit OFF & unplug the unit from its
power source.

2. Remove and clean the removable items
listed on the maintenance components

illustration for your specic model. Clean

ing warm water and mild detergent.

us
DRY parts completely.

3. With the steam generator cool, use a wire
brush or scrapper to loosen the mineral/
calcium deposits on the generator surface
and steam ports. Remove the loose built­up particles from the surface and wipe area
clean with damp cloth and reassemble the
unit.

NOTE: A certain
needed on the steam generator to ensure proper
steaming characteristics. If during cleaning,
the surface becomes free of all calcium/mineral
deposits, add tap water to the generator surface
and allow it to boil off. In soft water conditions,
a small amount of lime will season it.
(Seasoning Mixture, .75 oz. baking soda,
.75 oz. lime, 1 quart water), use enough to
cover bottom of the steam generator, turn
unit on and allow to evaporate.

Excessive Mineral Build-up

4. Use

5. Use

6. Install the diffuser, generator cover

6. Plug

7. Allow unit to reach operating

KEEP HANDS AND FACE AWAY

a delimer solution, which is safe
for cast aluminum, on the steam
generator surface. Follow the
instruction provide with the delimer
solution.

a dry towel or sponge to remove
the delimer solution, then rinse with
clean water.

secure with the wing nut as shown
here.

the steamer power cord into

power supply, and turn unit on.

the

temperature.

CAUTION

amount of calcium deposits are

Above: Inspect these area making sure they are
clean of deposits.

Below: Reinstall these parts before foperating the
steam feature during the cleaning procedure.

FROM THE UNIT WHEN OPERATING THE UNIT. STEAM ESCAPING IS VERY HOT.

8. Push the Green "Steam Shot" button several times to operate the steamer.
This removes any delimer solution from the generator surface.

9. Turn unit off, reinstall all remaining parts and return unit to operation.

10