Star Manufacturing CG14SPTS-120V, CG14SPTS-120C Operation Manual

®

SPLIT LID TABLE TOP

TWO SIDED TOASTER

MODEL

CG14SPTS-120V
CG14SPTS-120C

Installation and

Operation

Instructions

2M-Z5634 Rev. B 9/29/06

1

SAFETY SYMBOL

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specifi cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifi cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specifi cations. By using the information provided, the user assumes all risks in
connection with such use.

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record the model
number, serial number, voltage and purchase date in the area below and have it ready when you call to

ensure a faster service.

Model No.

Serial No.

Voltage

Purchase Date

Authorized Service Agent

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

The Star Service Help Desk

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone] Local [phone]

Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

2

GENERAL INSTALLATION DATA

CAUTION

This equipment is designed and sold for commercial use only by personnel trained and
experienced in its operation and is not sold for consumer use in and around the home nor
for use directly by the general public in food service locations.

The unit time and temperature are preset by the factory to the customer requirements. If
adjustments are required, refer to the time or temperature programming sections in this

manual.

INSTALLATION

1. Plug unit into dedicated 120V A.C. line with 20AMP receptacle.

2. DO NOT plug into 220V line. Doing so will damage the unit and void the warranty.

3. Each machine has been properly wired and inspected at the factory for operation on the
voltage and type of current specifi ed on the nameplate.

WARNING

DO NOT CONNECT TO ANY OTHER TYPE OF CURRENT OR THE
MACHINE WILL BE SERIOUSLY DAMAGED.

4. DO NOT operate without top burn guard in place.

INITIAL START UP

Before using the unit for the fi rst time, clean and heat for approximately 45 minutes.

OPERATING INSTRUCTIONS

Make sure unit is plugged into 20AMP receptacle and is on a dedicated 120V A.C. line.

1. Turn unit on by placing switch in "ON" position. The "Heat On" indicator, "START/
STOP" indicator and display will fl ash indicating unit is heating. When the preset
temperature is reached, the "Heat On" light, display and "START/STOP" light indicator
will stop fl ashing followed by 3 beeps. (Initial start-up heating time is approximately 30
minutes.)

2. Open lid on side where product will be cooked. Place product on bottom cooking
surface of the unit and close the lid.

3. Press the "START/STOP" button on the same side product is being cooked. The display
time will start to count down from the programmed time to "0:00." The countdown may
be stopped at any time by pressing and releasing the same "START/STOP" button. The
display will return to the programmed time.

4. When the countdown ends, the display will read "0:00" and the alarm will beep every
second. To turn off the alarm, press the "START/STOP" button. The display will return to
the programmed time.

5. Raise lid until it engages into the fi rst stop position and remove food. Using spatula,
scrape residue into grease catcher cup.

Note: Metal utensils may be used, however, using nonmetal utensils will
prolong the life of the cooking surface.

6. Turn the unit off when not in use.

Note: The right and left sides will operate independently of each other. Both
timers can be in operation at the same time. The "0:00" display will show
which side is timed out.

3

TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS

Start-up:

1. The preset time display will fl ash until preset temperature is reached.

2. When the control reaches preset temperature, time display, "Heat On" indicator and

"START/STOP" indicator will stop fl ashing and the alarm will beep three times.

Temperature:

1. To view the actual temperature, press and hold "Temp Button". Display will read

"Lo F" if temperature is below 273°F and "Hi F" if temperature is above 573°F.

To Program Time and Temperature:
Note: While programming, if no input is received for approximately 15

seconds, the unit will exit programming mode and revert to operational
mode.

1. Press and hold "Temp" (actual temperature displays).

2. While holding "TEMP", press and hold the "START/STOP" button on the left side for 3

seconds. The display above the "START/STOP" button will change from the time
to "_ _ _ _."

3. Release the "TEMP" and "START/STOP." The display on the left side will continue to

display "_ _ _ _." This indicates the unit is in program mode.

4. Press and release the "TEMP" button. The display will now be the current programmed

time for the "START/STOP" button.

5. Change and set the time by pressing and releasing or holding the "START/STOP"

button on the left side to change the time. The time will scroll forward from the current
programmed time. Once the time reaches 9:59, the time will change to 0:00 and continue
to go forward. Hold the "START/STOP" button down for faster changing of the time.

6. Once the time is set, press and release the "TEMP" button.

7. The current programmed temperature will now be displayed.

8. Change and set the temperature by pressing and releasing or holding the "START/STOP"

button on the left side. The temperature will scroll forward from the current programmed
temperature. Once the display reaches 550°F, the display will change to 273°F and
continue to go forward. Hold the "START/STOP" button down for faster changing of the
temperature.

9. Once the temperature is set, press and release the "TEMP" button.

THE TIME AND TEMPERATURE ARE NOW SET AND STORED IN MEMORY.

Notes:

The "HEAT ON" and "START/STOP" indicator and display will fl ash until the new

programmed temperature is reached.

Temperature setting is done with the Left Button only. The time setting programmed

on the left button will also be programmed onto the Right Button. See below to make
changes to the Right Button only. Each programming change must be saved by

pressing the "TEMP" button!

4