Page 1
User manual instruction
S66, S66
bt gsm
S96, S96
bt gsm gps
security systems
Page 2
StarLine S96, S66
2
Contents
General description ................................................................................ 8
Main advantages ................................................................................................................. 8
The plastic card ..................................................................................................................10
The tag ..................................................................................................................................11
Specications ........................................................................................ 13
Light and sound indication .................................................................. 14
Operation modes ................................................................................... 15
«Security on» mode ..........................................................................................................15
«Security o» mode ..........................................................................................................16
«Alarm» mode .....................................................................................................................17
«Panic» mode ......................................................................................................................17
«Anti hijack» mode ...........................................................................................................17
«Slave» mode ......................................................................................................................18
«Hands free» mode ...........................................................................................................19
Service (Valet) mode ........................................................................................................19
«Drive prohibition» function ........................................................................................ 20
«Engine starting» function ........................................................................................... 20
«Engine starting preheater» function ........................................................................24
«Turbotimer» function .................................................................................................... 25
GSM control commands ........................................................................ 26
Change settings ..................................................................................... 28
Registration of tags and smartphones ................................................ 29
Emergency security deactivation ........................................................ 33
Change of owner authorization code .................................................. 35
Owner authorization code .................................................................... 37
Page 3
user manual instruction
3
Attention!
Prior to operation of the security system carefully read this manual
paying special attention to the sections marked
and determine
whether this security system is suitable for your car, for which
following the car manufacturer’s requirements and the car operation
manual.
If you could not determine whether this security system can be
installed on the car, return it to the seller within 14 days after purchase.
The security system is a complicated technical device implying
connection to the car circuits related to engine operation.
The security system should be installed only by specially trained
qualied specialists.
Mounting, programming, maintenance, repair and disassemblyassembly of the security system shall not be carried out by persons
who are not qualied specialists and have not passed training and
knowledge test in safety rules.
During security system parameter programming, the set parameters
should not contradict the requirements of the car operation manual.
The user bears full responsibility for damage incurred to people,
animals and assets as a result of inappropriate use of the security
system or use with violations of the safety requirements specied in
this manual.
The manufacturer shall should not be responsible for losses and
injuries caused by failure to observe the safety rules and requirements
outlined in this manual.
To avoid possible misunderstandings, keep the documents enclosed
to the security system at sale. Check lling-in of the warranty slip,
include the date of sale and seller’s stamp. If there is no sale (purchase)
date, the warranty period is counted from the date of security system
manufacture.
Page 4
StarLine S96, S66
4
If your security system has a remote key or a wireless tag:
• Do not carry the remote key or tag on the same bundle with
the car keys
• Always switch over the system to the service mode when
handing the car over for maintenance or washing. Do not
hand tags and remote keys over to third parties to prevent
unauthorized access to security functions
• Do not leave remote key or tags in areas accessible to children
and animals
• Do not let liquids ingress the remote key
• If the remote key display shows an icon warning about remote
key battery discharge, take timely measures to replace the
battery.
• Store the spare battery in the car in the factory packing
Page 5
user manual instruction
5
Mandatory safety measures during use
of the engine starting function
It should be borne in mind that the car is a source of extra hazard.
Before security system operation, carefully study the measures for safe
use of the function of remote or automatic engine starting outlined
below:
1. Always park the car on an open, well ventilated area;
2. Always apply the car’s parking brake, which shall be operable and
prevent car movement;
3. Leaving the car, be sure to set the automatic transmission control
lever to the «PARK» position, and the manual gearbox changeover
lever – to the neutral position;
4. If your car has a manual gearbox, prior to activating the function of
remote or automatic engine starting, be sure to perform the procedure
of preparation for engine starting – «program neutral»;
5. Never hand over the security system control remote key to children and
other persons without their preliminary study of the operation manual;
6. Before activating the function of remote or automatic engine
starting:
• make sure the car is operable;
• make sure there is a sucient amount of fuel, oil, cooling uid
etc;
• set the operation parameters of the passenger compartment
heater (air conditioner), window heating and other accessories
to the required levels;
• set the passenger control ventilation regulator to air circulation,
which will allow more ecient warming or cooling of air in the
car.
Page 6
StarLine S96, S66
6
Safety precautions during charging of your car’s
storage battery
Remember that any battery charging process implies supply of voltage
exceeding the rated 12 V to the storage battery and accordingly to
the car circuit, which may damage the car electronic equipment and
additional installed equipment in your car.
Do not use charging and starting/charging devices for storage battery
charging directly on the car without disconnecting the storage
battery terminals from the car circuit in the following modes:
• rapid charging by increased current («boost» or similar
modes)
• various START modes intended for engine starting
• in the storage battery 24 V charging mode
Never use starting and charging devices for engine starting without
a connected storage battery and with connected inoperable storage
batteries (short circuits in banks, breakage of plates etc.)
Never use inoperable charging devices, 24 V charging devices and
devices not intended for storage battery charging, e.g., welding
invertors.
All the aforesaid devices and modes may cause uncontrolled supply
of increased voltage over 25 V and up to 60 V to the car circuit and
cause failure of the electronic components of the security system and
car equipment.
The light-up method should not be used for storage battery charging.
Even the described «safe» light-up methods are safe only for the
«donor» car. Connection and disconnection of a fully discharged or
inoperable storage battery on your car with the engine operating may
cause failure of the electronic devices of your car and the car alarm
due to a short circuit or surges of increased voltage occurring during
storage battery connection and disconnection.
Page 7
user manual instruction
7
If the aforesaid devices and modes are used, the car owner shall be
responsible for damage of the electronic equipment.
Observe the technology for safe storage battery charging!
Before charging, the storage battery terminals shall be disconnected
from the car circuit. After that the storage battery charging process
can be started. After charging, connect the storage battery to the car
circuit.
This is necessary because without measuring devices you cannot
determine storage battery operability or status and the reason of its
discharge (internal short circuits or breaks). Any connection of the
charging device to an inoperable storage battery causes the risk of
damage of the car electronic equipment and the security system by
increased voltage.
Page 8
StarLine S96, S66
8
General description
Security telematics systems StarLineS96 and StarLine S66 (hereinafter
the system) are intended for vehicle protection from theft and armed
assault.Authorization of the owner occurs as a result of wireless exchange
between the tag (or smartphone) and the main unit using the Bluetooth
Smart (BLE) protocol using an algorithm that is protected from interception
at the time of device registration. Use the tag or a smartphone supporting
the BLE protocol and registered in thesystemusing theStarLine mobile
application for authorization.
The system is controlled by SMS commands, voice menu, wireless tag,
from the StarLine mobile application or from the personal account on the
website starline.online.To enter the personal account use the login and
password given on the owner’s plastic card included in the delivery set.
The functions of automatic and remote engine starting are available for
theStarLine S96system.
Main advantages:
• operation in the «Slave» mode (security mode activation or
deactivation using the factory car remote key);
• driver identication by means of the wireless tag or smartphone via
the Bluetooth Smart protocol;
• connection of wireless underhood unit StarLine R6 for control of
the hood locks, horn and engine blocking;
• additional owner authorization by means of a wireless tag,
smartphone or entry of the secret code by means of the factory
buttons;
• a dialogue code of StarLine control with individual 128 bit
encryption keys, guaranteeing reliable protection from all known
code grabbers;
• the possibility to install the 2CAN+2LIN module for reception of
statuses and control via the CAN bus;
Page 9
user manual instruction
9
• remote and automatic engine starting (for StarLine S96);
• temporary deactivation of the standard immobilizer using the
iKEY technology (via the digital CAN and LIN buses) or Fortin and
iDataLink module control;
• determination of transport vehicle coordinates, speed and
movement direction;
• determination of driving parameters, driving style;
• monitoring of car parameters (mileage, error codes, mains voltage
etc);
• automatic data transmission to the monitoring server;
• data recording and storage in the non-volatile memory («black
box»). The event log contains information on tracks for the last 1000
kilometers at driving in the city and 5000 — on the highway and on
13000 events;
• control of functions and display of parameters on the monitoring
server and in the StarLine mobile application;
• high-sensitivity GLONASS+GPS module;
• the service button combined with the LED indicator of system
status;
• universal recongurable outputs/inputs;
• the special StarLine Master program, used for individual setting of
the system depending on owner’s wishes and car’s peculiarities.
Page 10
StarLine S96, S66
10
The plastic card
The delivery set includes a plastic card containing the following data:
• Login and password — the user’s personal account on the website
starline.online where security system control and parameter
changing are available.
• Code of emergency security deactivation — the code is given
on the owner’s plastic card. It is used for emergency security
deactivation.
• Service code — the code is given on the owner’s plastic card. It is
used for entry in the StarLine Master application.
ATTENTION! Do not tell the code of emergency security
deactivation to anybody! Remember that a malefactor,
knowing the code, may deactivate the protective functions.
Page 11
user manual instruction
11
The tag
The presence of a tag depends on the set of
the system
ATTENTION! The tags, which are included in
set, are initially in transport mode, in which
they are disabled! Pressing the tag button in
this mode will be indicated by the green and
red ashes of the built-in LED.
Before operating, it is necessary to press the
tag button several times before changing the
color of the ashes to green.
As the tag, you can use a smartphone that supports the
Bluetooth Smart protocol.
A smartphone and the tag equivalent to the functionality
when used for additional authorization of the owner in the
«Free Hands» mode and «Slave» mode.
System control
Duration of pressing the tag button:
• short— press and release the button, then a ash corresponding to
the current mode of operation will follow;
• long — hold the button until the LED ashes. The duration of
depression can be of two levels:
• 1 level — hold the button until a long ash of the LED
corresponding to the current mode of operation appears;
• 2 level — press and hold the tag button, followed by two
short ashes and one long one, and again a series of short
ashes— release the button.
Page 12
StarLine S96, S66
12
Command Duration of pressing
Arm / Disarm 1 short
Enable / Disable «Anti-hijack by the tag» long (1 level)
Enable / Disable Service mode long (2 level)
Replacing the tag’s battery
If the tag’s battery is discharg, then when the ignition ON 3 sounds of
the buzzer will sound and an SMS will be sent to the owner number. We
recommend that you replace the battery as soon as possible.
To replace the battery with a neatly at metal or plastic object (metal
ruler, thin plastic) open the tag body and, observing the polarity (as
pictured in the photo), install the battery in the compartment. Before
closing the tag body, install a waterproof seal between its parts. After
installing the battery in the tag, the system is ready for operation.
Page 13
user manual instruction
13
Specifications
Parameter Value
Radio exchange protocol Bluetooth Smart
Interfaces • 2 CAN
• 2 LIN
• 1 universal code bus StarLine Bus
• 1 USB
• 18 recongurable channels:
• 17 outputs of OC (open collector) ОК –0,2А
• 2 outputs 2А
• 3 positive inputs
• 3 negative inputs
• 1 universal input
•a connector for the engine temperature
sensor
• a connector for the valet button
Supply voltage 8-16 V
Rated current 15.2 mA
Operating temperature range from −40 to +85 °С
Overall dimensions of main unit 10 6х63х17 mm
Weight 63 g
Page 14
StarLine S96, S66
14
Light and sound indication
The security system informs about its status by means of sound (horn)
and light signals (turn signals)
— short signal
— long signal
Event Light signals Horn
Security activation
Security activation with
security zone breach
Security activation with
deactivation of «Hands free»
Security activation with
deactivation of «Hands free»
mode with security zone
breach
Security deactivation
Security deactivation (one of
the zones was violated in the
security cycle)
Alarm 30 s 30 s
Warning level alarm
Panic 10 s 10 s
Exit from service mode
Page 15
user manual instruction
15
Operation modes
The security modes protect the car against theft.
Security modes
Security on
Security o
Alarm
Panic
Additional modes
Slave
Hands free
Service mode
Device registration mode
Telematic setting mode
The additional modes are intended for setting of the system parameters
(telematic setting mode), adding of new devices (device registration
mode), deactivation of protective functions for car handover for
maintenance (service mode) and convenient system control («Slave»
mode, «Hands free» mode).
«Security on» mode
The following zones are monitored in the «Security on» mode: ignition,
doors, trunk, hood, shock sensor, tilt sensor, movement sensor,
additional sensor. If a zone is violated, the system will set to the «Alarm»
mode.
Security activation is performed only with the ignition o.
If a security activation command is sent with the ignition on, only
closing of the central lock will be performed.
Security activation is performed by one of the following methods:
• by SMS-command 11;
• by command
11 from the voice menu;
• from the StarLine mobile application;
Page 16
StarLine S96, S66
16
• from the personal account on the website starline.online;
• by activation of standard system security in the «Slave» mode;
• in case of tag loss or touch of the door handle sensor in the
«Hands free» mode;
• by single pressing on the tag button in the «Security o» or
«Alarm» mode.
The system will conrm successful security activation by one sound
signal and one ash of light emergency alarm.
If the doors, hood, trunk are not properly closed, the parking
brake is not tightened, the brake pedal is pressed or one of the
limit switches of the doors, hood, trunk is faulty (constantly
closed), the system will warn thereof by 4 sound signals and 4
ashes of light signals.
Restore the violated security zone and check presence of a
single conrmation signal on switchover to the security mode.
«Security off» mode
Security deactivation is performed by one of the following methods:
• by SMS-command 10;
• by command
10 from the voice menu;
• from the StarLine mobile application;
• from the personal account on the website starline.online;
• deactivation of standard system security («Slave» mode);
• in case of tag detection or touch of the door handle sensor
(«Hands free» mode);
• by single pressing on the tag button in the «Security on» mode.
Successful security deactivation will be conrmed by 2 sound signals
and 2 light signals. If the «Alarm» mode was activated during security,
3 sound signals and 3 ashes of light signals will follow.
After system security deactivation, the remote key screen will display
all the events which occurred during the security.
After security deactivation, if no actions are taken, the
system will automatically set to the «Security on» mode and
close the central lock in 30 seconds.
Page 17
user manual instruction
17
«Alarm» mode
The «Alarm» mode is activated at violation of any zone in the
«Security on» mode. The system will switch on sound alerting by
the horn and light emergency alarm for 30 seconds and will notify
the owner (telephone call, SMS-message, notification in the mobile
application). If the zone is not restored, the system will repeat the
alarm cycle once more.
If a warning zone is violated, 3 light signals and 3 long horn signals
will follow.
The «Alarm» mode is reset without security deactivation by a short
pressing on tag button.
ATTENTION! The maximum number of zone actuations is
limited to 8 repetitions per 1 security cycle.
«Panic» mode
The «Panic» mode is intended to ensure safety of the owner and car.
This mode is activated by owner’s command by SMS-command
19.
Upon command reception the system activates sound alerting by the
horn and emergency light alarm for 10 seconds to attract the attention
of nearby persons.
«Anti hijack» mode
The «Anti hijack» mode is intended for driver protection against
assault during driving.
The mode is activated by one of the following methods:
Режим включается одним из способов:
• by SMS-command 31;
• by command
31 from the voice menu;
• from the StarLine mobile application;
• from the personal account on the website starline.online
Page 18
StarLine S96, S66
18
Upon command reception the system will issue warning signals of
upcoming engine blocking by the horn and light emergency alarm
for 30 seconds. At speed decrease below 30 km/h the engine will be
blocked.
s
km/h
Exit from the «Anti hijack» mode and engine unblocking is performed
by one of the following methods:
• SMS-command 30 хххх, where хххх is the code of emergency
security deactivation is given on the owner’s plastic card;
• by entering the code of emergency security deactivation given
on the owner’s plastic card, by means of the service button;
• from the personal account on the website starline.online. It is
necessary to enter the code of emergency security deactivation
given on the owner’s plastic card.
Operation of the «Anti hijack at tag loss» mode is described
in the electronic manual on the website
help.starline.ru.
«Slave» mode
The «Slave» mode allows for system control by means of the standard
alarm remote key.
In this mode, additional owner authorization by presence of the tag is used.
At deactivation of standard alarm security, the system checks presence of the
tag in the identication zone. If the tag is found, car security is deactivated.
If the tag is not found within 10 seconds, the system will set to the «Alarm»
mode.
Page 19
user manual instruction
19
«Hands free» mode
Use the wireless tag or smartphone for the «Hands free»
mode.
The «Hands free» mode is intended for automatic control of security
activation/deactivation according to tag presence.
When the tag is present near the car, security deactivation is
performed automatically. When the tag disappears from the visibility
zone, the system sets to the «Security on» mode.
The «Hands free» mode can be activated or deactivated by SMScommand (
71 or 70, respectively), a command from the voice menu,
from the mobile application or personal account on the website
starline.online
.
Service (Valet) mode
The service mode is intended for temporary deactivation of
security functions and prohibition of access to system settings. It is
recommended for the maintenance period.
The service mode can be activated only from the «Security
o» mode near the car.
Switch over to the service mode is performed by one of the following
methods:
• holding of the tag button for 5 seconds;
• by SMS-command
51;
• by command
51 from the voice menu;
• from the StarLine mobile application;
• from the personal account on the website starline.online.
Switch over to the service mode will be conrmed by yellow indication
of the tag LED.
Page 20
StarLine S96, S66
20
ATTENTION! In the service mode, transition to the other
additional modes is prohibited!
Exit from the service mode is performed by one of the following
methods:
• holding of the tag button for 5 seconds;
• by SMS-command
50;
• by command
50 from the voice menu;
• from the StarLine mobile application;
• from the personal account on the website
starline.online
.
«Drive prohibition» function
Use of the «Drive prohibition» function prohibits driving without
additional owner identication.
Additional authorization is performed by entering the code of
owner authorization using the standard car buttons (for instance,
the multimedia control buttons on the steering wheel, window
raiser control buttons) at each security deactivation. The code is
enteredwith the ignition switched-o.
If the owner authorization code is not entered, then if an attempt at
driving is made, the engine will be blocked for 1 minute or until entry
of the owner authorization code.
«Engine starting» function (only for StarLine S96)
The starting function allows for remote and automatic car engine
starting/stopping.
Preparation of a car with manual transmission for remote and
automatic engine starting.
Before engine starting, perform the procedure «program neutral»:
• apply the parking brake with the engine operating. The LED on
the service button will light up;
Page 21
user manual instruction
21
• take the key out of the ignition lock. The engine will continue
operating;
• leave the car, close the doors, trunk, hood and send the
“Security activation” command. The engine will be stopped;
• the system will set to the security mode;
• the «N» pictogram will appear on the StarLine mobile
application or personal account on the website starline.online ;
• the system is ready for remote and automatic engine starting.
If the door is opened or ignition is switched on after fulllment
of the «program neutral», remote and automatic engine
starting will be canceled until the next execution of the
«program neutral» algorithm.
Preparation of a car with automatic transmission for remote and
automatic engine starting
Make sure the automatic transmission selector is in the «Parking»
position.
Engine starting
Remote engine starting is performed by one of the following
methods:
• by SMS-command 21;
• by command
21 from the voice menu;
• from the StarLine mobile application;
• from the personal account on the website starline.online
Automatic engine starting can be performed according to one of
the conditions:
• according to temperature value. Engine starting at engine
temperature decrease below the specied value. The
temperature value is set in the StarLine application or in the
personal account on the website starline.online;
Page 22
StarLine S96, S66
22
• according to value of storage battery voltage. Engine starting
at storage battery voltage decrease. The voltage value is set in
the StarLine application or the personal account on the website
starline.online;
• periodic. Engine starting with the preset operation period after
the preset recurrent time interval. The interval and period are
set in the StarLine application or the personal account on the
website starline.online;
• by alarm clock. Engine starting at the preset time. Engine
starting schedules are set in the StarLine application or the
personal account on the website starline.online.
The minimum time of engine operation at remote starting is 10
minutes. It can be changed in the personal account on the
website
starline.online
or in the StarLine mobile application.
Extend engine operation by SMS-command
21, command21 from
the voice menu, command from the StarLine mobile application
or from the personal account on the website
starline.online
.
ATTENTION! Automatic engine starting will not take place
if less than 1 hour has passed after the last start or the
previous automatic start has failed.
Upon drive completion, automatic engine starting is
possible not earlier than 5 minutes after engine stopping.
Engine stopping
The engine is stopped if:
• the owner sent a command (SMS-command 20, command
20 from the voice menu, command from the StarLine mobile
application or from the personal account on the website starline.
online);
• the “Alarm” mode is activated;
• the car has started moving;
• the hood is open;
Page 23
user manual instruction
23
• the parking brake is o (for cars with manual transmission);
• the automatic transmission selector was switched over from the
«Parking» position (for cars with automatic transmission);
• the brake pedal is pressed.
Car driving continuation after remote engine starting
To continue driving the car, without stopping the engine after remote
starting, do as follows:
• for cars with ignition lock:
• deactivate system security;
• insert the key into the ignition lock, turn it to position «Ignition
on» and start moving;
• the LED on the valet button will go out at movement start, pressing
of the brake pedal or parking brake release;
• for cars with START/STOP button:
Several options are possible depending on the car and system
connection method:
• rst variant (*):
• deactivate system security;
• hold the brake pedal for 3 seconds;
• the LED on the service button will go out, after which movement
can be started (the START/STOP button need not be pressed);
• second variant (*):
• deactivate system security;
• press the START/STOP button 1 or 2 times (*);
• the LED on the service button will go out, after which movement
can be started.
(*) Ask the installation specialist during mounting about the
connection method of your system and the operation
algorithm.
Page 24
StarLine S96, S66
24
Function «Engine starting preheater»
The function allows for engine preheating before starting. The starting
preheater can be controlled both in the manual and automatic mode.
Manual mode
In the manual mode the starting preheater is switched on/o by a
command.
The starting preheater can be switched on by one of following methods:
• by SMS-command 221;
• from the StarLine mobile application;
• from the personal account on the website starline.online.
Time of preheater operation in this mode is 20 minutes. It can
be changed in the personal account on the website
starline.online
or in the StarLine mobile application.
ATTENTION! If the starting preheater has normal settings,
diering from those set in the personal account, operation
time may dier from the specied one..
Operation can be prolonged by sending a repeated command for
starting preheater switch-on.
The starting preheater can be switched o by one of following methods:
• by SMS-command
220;
• from the StarLine mobile application;
• from the personal account on the website starline.online.
Automatic mode
The automatic mode is activated by the installation specialist
during system setting after mounting.
In the automatic mode the starting preheater is switched on before
operation of engine remote and/or automatic starting. If engine
temperature before remote or automatic starting is less than specied,
the starting preheater will be started. The engine will be started after
engine warm-up to the preset temperature (during automatic starting) or
upon expiry of the preset time.
Page 25
user manual instruction
25
The starting preheater is switched o upon expiry of the specied time or
reaching of the switch-o temperature threshold.
Time of preheater operation in this mode is 10 minutes. Operation can
be prolonged by manual sending of a repeated command for starting
preheater switch-on.
Operation time and switch-o temperature threshold of the starting
preheater can be changed in the personal account on the website
starline.online
or in the StarLine mobile application.
Function «Turbotimer»
Use the function «Turbotimer» for turbocharged cars for engine
turbine cooling.
The «Turbotimer» function is activated by a installer during
installation.
Activate the function as follows:
• apply the parking brake with the engine operating. The LED on
the valet button will light up;
• take the key out of the ignition lock. The engine will continue
operating;
• leave the car, close the doors, trunk, hood and activate the
“Security on” mode;
• the engine will be stopped when the turbine cools down.
Turbine cooldown time is calculated automatically and
depends on engine speed before the drive end. The
maximum turbine cooldown time is 5 minutes.
GSM control commands
System control by means of GSM commands is only possible if
the GSM module is available.
The telephone number, from which the rst call to the system number
was made, will be recorded automatically as the owner’s main number.
Page 26
StarLine S96, S66
26
All commands from this number are sent without a GSM-password. To
send commands from other numbers, a password shall be entered in the
beginning of the command text (for instance, send the following SMSmessage for security activation “1234 11”, where 1234 — GSM password,
11 — command number).
The GSM-password is set from the owner’s main number at the rst call.
The control commands are given in the table.
SMS command text Command meaning
10
Deactivate security
О-
11
Security activation
О+
12 Security activation without shock sensor
13 Security activation without an additional sensor
14
Security activation without preliminary level of the shock
sensor
15 Security activation without tilt sensor and motion sensor
19
Activation of the «Panic» mode
PANI C
20
Remote engine stopping
D-
21
Remote engine starting
D+
220 Switch o of the starting pre-start engine heater
221 Switch on of the starting pre-start engine heater
Page 27
user manual instruction
27
SMS command text Command meaning
30 ХХХХ
Deactivation of the «Anti hijack» mode, where хххх is the
code of emergency security deactivation is given on the
owner’s plastic card
А- ХХХХ
31
Activation of «Anti hijack» mode
А+
40
Car coordinate request
GPS
41
Car state request
AUTO
45
Request about the state of GSM/GPRS connection and
balance data
BALANCE
MONEY
50
Deactivation of the service mode
S-
51
Activation of the service mode
S+
70
Deactivation of the «Hands free mode»
R-
71
Activation of the «Hands free mode»
R+
Page 28
StarLine S96, S66
28
Change settings
Change of user settings is available in the personal account on the
website starline.online
Page 29
user manual instruction
29
Registration of tags and smartphones
Use the «Device registration» mode for registration of new tags and
smartphones.
To prevent unauthorized adding of new components, entry in
the device registration mode is possible only from the «Security
o» mode.
ATTENTION! Tags and smartphones shall be registered in one
cycle. At registration of new tags and smartphones all previous
tags and smartphones will be deleted from memory. It will be
necessary to register them again. In total, up to 5 devices can be
registered in the system.
Entry in the device registration mode
1) Deactivate system security.
2) Switch o ignition (if it is on).
3) Press the service button 7 times.
4) Switch on the ignition. 7 light LED ashes of
service button and 7 siren sounds will follow.
5) Entry in the registration mode will be
conrmed by 2 short service button LED
ashes and 2 siren sounds.
Page 30
StarLine S96, S66
30
Tag registration
1) Remove the battery from the tag.
2) Press and hold the tag button and install the
battery. The tag LED will light up red.
3) Release the button and check presence of a
series of red ashes for 10 seconds.
4) Successful registration will be conrmed by a
green ash and 2 tag LED slashes and 2 siren
sounds. If the tag was not registered, the tag
LED will light up red.
5) Repeat items 1-3 for the remaining tags.
Page 31
user manual instruction
31
Smartphone registration
Register the smartphone using the StarLine
mobile application (see the application menu
«Smartphone as a tag»):
- enable Bluetooth in smartphone and activate
Search;
- for Android - enter code 000000; for iOS activate Pairing, if code is required - enter
000000.
Exit from the device registration mode
Exit from the device registration mode is
performed automatically in 5 minutes or at
ignition switch-o.
Exit from the “Device registration” mode will
be conrmed by 2 service button LED ashes, 2
siren sounds and then serial signals by a number
of total registered tags and smartphones.
After registration, an SMS message with the list
of registered devices will be sent to the owner’s
telephone.
Page 32
StarLine S96, S66
32
Emergency security deactivation
If the tag was lost, the tag battery has discharged, there is no access to
the mobile application or the «Anti hijack» mode is on, use the code of
emergency security deactivation given on the plastic card.
Do the following to deactivate system security:
1) Switch on the ignition. The «Alarm» mode is
activated.
2) Press the service button the number of times
corresponding to the rst digit of the code of
emergency security deactivation.
Page 33
user manual instruction
33
3) Switch ignition o. The LED on the service
button will light up, the number of ashes will
correspond to the ordinal number of the digit
of emergency disarm code (1,2, 3 or 4 times).
4) Switch on the ignition.
5) Repeat items 2-4 for the remaining code digits.
If the emergency disarm code is entered correctly, 3 short siren sounds
and 3 service button LED ashes will follow. The system will set to the
«Security o» mode.
If the code of emergency security deactivation is entered
incorrectly 3 times, the possibility of repeated code entry
will be blocked for 15 minutes and an SMS-notication will
be sent to the owner’s telephone.
An attempt at digit entry will be indicated by 5 LED ashes.
Page 34
StarLine S96, S66
34
Example of entry the code 5342
Page 35
user manual instruction
35
Change of owner authorization code
The owner code is used for user authorization by means of the
standard car buttons.
Do as follows to change the owner authorization code:
1) Deactivate system security.
2) Switch o ignition (if it is on).
3) Press the service button 7 times.
4) Switch ignition On. 7 service button LED
ashes and 7 siren sounds will follow. Entry in
registration mode will be conrmed by 2 short
LED ashes and 2 siren sounds.
5) Enter a new owner authorization code using
the standard car buttons with pressing interval
not more than 3 seconds. Each pressing of the
standard button will be accompanied with a
single ash on service button LED.
Page 36
StarLine S96, S66
36
The owner authorization code consists of a code sequence,
containing from 5 to 30 pressings of the standard buttons.
The list of standard buttons supported by the car is given on
the website can.starline.ru
If LED ash does not follow while pressing of an original
button, so the button is not supported in the car.
6) In 3 seconds after owner’s code entry, 2 short
service button LED ashes and 2 siren sounds
will follow, conrming code acceptance.
7) Enter the owner authorization code again.
8) If the code is entered correctly, 2 short LED
ashes and 2 siren sounds will follow. If the
code is entry is failed, 4 short LED ashes will
follow, in this case repeat items 7 and 8.
9) In 10 seconds switch ignition O to exit the
registration mode.
10) Exit from the registration mode will be
conrmed by 2 service button LED ashes,
2 siren sounds and then serial signals by
a number of total registered tags and
smartphones.
Page 37
user manual instruction
37
Owner authorization code
This section is completed by an installer
Page 38
StarLine S96, S66
38
Page 39
user manual instruction
39
Page 40
StarLine S96, S66
40
The manufacturer reserves the right to modify and improve the
product design and technical features without prior notice.
Manufacturer:
ScPA “StarLine” LLC,
Komissara Smirnova str., 9,
194044, Saint-Petersburg, Russian Federation
Tel. +7 812 3263333
www.alarmstarline.com
Loading...