Star Lights 2000 User Manual

SMART LIGHT 2000™

INSTALLATION AND OPERATIONS

INSTRUCTIONS

‐1‐



THANK YOU FOR CHOOSING THE SMART LIGHT 2000

We are very pleased that you have chosen our product to enhance your camping experience! At Starlights, Inc.,
we are passionate about improving your safety, security, and convenience. We feel that the Smart Light 2000
represents a giant step forward in improving an already wonderful experience – Rving!

Developed and designed in the United States, by RVers, for RVers, the Smart Light 2000™ has the versatility to
adapt to differing park conditions, or to dry camping conditions. Your new Smart Light 2000™ also monitors
your battery levels, and will notify you of any serious reduction in power. We are confident that you will be
completely satisfied with your new Smart Light 2000™ for years to come. Happy camping!

Jason P. Weaver
President, CEO
Starlights, Inc.

CONTENTS of Box

The Smart Light 2000™ packaging should include the following parts to make the Installation simple and
convenient.

™

!

™

1. One lighting fixture complete with the NEW REVOLUTION 200™ LED Bulb

2. Four mounting screws

3. Instruction Manual

BULB REQUIREMENT for the Smart Light 2000

OPTIONAL ACCESSORIES

 Revolution LED Bulbs.

 The Smart Light Fuse Switch Box™ which allows the attachment of the Smart Light 2000 Scare

Light™ to the Smart Light 2000™.

 Smart Light 2000 Scare Light™

 Smart Light 1000™ Motion Light

 Amberizer™ Antibug Bulbs

 Amber Lens

INSTALLATION & SAFETY INSTRUCTIONS

For the Smart Light 2000® RV Motion Light

IMPORTANT SAFETY INFORMATION

 Disconnect battery before installing or replacing the motion sensor lighting fixture.
 A person familiar with the installation of 12 Volt lighting products is recommended for the installation of

this product.

 This motion sensor light is designed to be used only with 12 DC Power [Automotive type], any

modifications of the unit may result in a hazard and WILL VOID the WARRANTY.

 The Smart Light 2000
 Please do not attempt to open the motion sensor back housing as there are no serviceable parts inside and

doing so WILL VOID the WARRANTY.

 Please read all of the Smart Light 2000™ installation instructions before installing the fixture.

™

lighting fixture must be installed in accordance with any state and national codes.

®

-“1156” or the Revolution LED Bulbs.

‐2‐



IMPORTANT NOTES

 Using or attaching other accessories or devices can cause a hazard, may damage the unit, and WILL

VOID the WARRANTY.

INSTALLING THE Smart Light 2000

™

IMPORTANT-DISCONNECT THE BATTERY

STEP 2: Attach the WHITE wire marked positive (+) on the SL-2000™ fixture to the positive wire (+)

STEP 3: Attach the WHITE wire marked negative (-) on the SL-2000™ fixture to the negative wire (-)

STEP 1: Remove the old lighting fixture from the RV and clean area of all old sealer, dirt, etc.

NOTE: If you are using the optional Fuse Box to activate your Scare Light now is the time

to add that accessory using the installation instruction included with the Fuse Box.

coming from the RV.

coming from the RV.

NOTE: Perform functionality test at this step

The Smart Light 2000™ is reverse polarity protected. If it is wired backwards, the unit will not be
damaged. However, if wired incorrectly, the motion sensing functionality will not work, even though the
light can be turned on and off at the switch as with any other porch light. Thus, it is imperative that you
perform this self test in order to assure proper functionality. To do this test you will have to reconnect the
battery.

First, adjust your interior light switch to the ‘ON’ position. Then, turn the light switch ‘OFF’, then ‘ON’
again. If at this point you find that the incandescent light bulb turns on, but the BLUE LED does not blink

on and off, then switch the positive and negative wires connecting the Smart Light to your vehicle. Next,

perform the self test once again as described above. If your light again fails to operate in the auto mode as
indicated, please stop the installation process and contact us at 1-800-883-5444. If the functionality test is
successful, again DISCONNECT THE BATTERY and proceed with the installation.

STEP 4: Using the FOUR (4) screws provided, attach the Smart Light 2000™fixture to the exterior of the

RV. In most cases, the previous holes used to mount the old fixture can be reused to mount the

Smart Light 2000™. However, if you must drill new screw holes into your substrate, make sure to

properly fill in the old holes before mounting your light.

NOTE:

Some models may have differing hole depths and/or widths. Thus, the screws provided may not be
sufficient. If you find this to be the case on your model, simply substitute the enclosed screws for those that
will fasten the unit properly.

STEP 5: Remove the Clear plastic plug to gain access for the adjustment of the Variable Resistor

(Potentiometer) for sensitivity. The adjustment is clockwise to increase sensitivity, and
counterclockwise to decrease sensitivity. When adjusting this resistor, take care not to touch the
mother board, which could damage the unit and WILL VOID the WARRANTY. Please note
that the Smart Light 2000™ fixture comes from the factory set at the most sensitive setting and

may need adjustment to a lower sensitive setting to match the camping environment.

IMPORTANT – DISCONNECT THE BATTERY BEFORE ADJUSTING

The Potentiometer is located on the circuit board mounted in the electronics compartment of the Smart

Light 2000

™

fixture located above the light sensor and below the multicolored LED. To adjust the

‐3‐

