Star Headlight & Lantern ULB9, ULB9S, RLKULB9-1, RLKULB9S-1, FLKULB9 Instructions Manual

Star Mini Phantom

™

Interior Undercover Mini LED Light

PATENTS D530,029 and D632,421

ULB9 Series

(Discrete LEDs)

ULB9S Series

(Starburst LEDs)

IMPORTANT: Please read all of the following instructions before installing your new light.

CAUTION: Please be sure to check that your cigarette plug outlet or hard wire is properly

fused with a 5 amp fuse. Testing the light before this fuse is properly
installed will void the warranty on the light.

This light is designed to be mounted on the inside of your vehicle.
It is not intended for exterior applications and is not warranted
against water damage.

It is the sole responsibility of the owner to ensure the warning light is
secure. Check your light every time you enter the vehicle to ensure that
it is mounted securely. The manufacturer assumes no responsibility for
the secure mounting of this light.

PLITSTR46 REV. L 6/20/16

Parts

ULB9-**: 1 Standard Mini Phantom Head with Cig Plug
1 274-ULB9BKT Mounting Kit

ULB9S-**: 1 Starburst Mini Phantom Head with Cig Plug
1 ULB9-HOOD-1 Flashback Hood with Windshield Brackets

1 S111-6 Hood Gasket
1 PLABULB9 Reflective Hood Label
2 P30019-267 Pivoting Flush Mount Brackets

ULB9-1-**: 1 Standard Mini Phantom Head with Hardwire
1 274-ULB9BKT Mounting Kit

ULB9S-1-**: 1 Starburst Mini Phantom Head with Hardwire
1 ULB9-HOOD-1 Flashback Hood with Windshield Brackets

1 S111-6 Hood Gasket
1 PLABULB9 Reflective Hood Label
2 P30019-267 Pivoting Flush Mount Brackets

RLKULB9-1-**: 2 Standard Mini Phantom Head with Hardwire
2 274-ULB9BKT Mounting Kit

RLKULB9S-1-**: 2 Starburst Mini Phantom Head with Hardwire
2 ULB9-HOOD-1 Flashback Hood with Windshield Brackets

2 S111-6 Hood Gasket
2 PLABULB9 Reflective Hood Label
4 P30019-267 Pivoting Flush Mount Brackets

FLKULB9-**: 2 Pre-Connected Standard Mini Phantom Heads with Cig Plug
2 274-ULB9BKT Mounting Kit

FLKULB9S-**: 2 Pre-Connected Starburst Mini Phantom Heads with Cig Plug
1 ULB9-HOOD-1 Flashback Hood with Windshield Brackets
1 ULB9-HOOD-2 Flashback Hood with Windshield Brackets

2 S111-6 Hood Gasket
2 PLABULB9 Reflective Hood Label
4 P30019-267 Pivoting Flush Mount Brackets

Mini Phantom Head
w/Standard LEDs

274-ULB9BKT

ULB9-BKT

274-ULB9MMC

DL15-CUP Suction Cups

(qty=2)

P30019-253
Flush Mount Hood for ULB9

(OPTIONAL)

ULB9-HOOD
Hood for use with
ULB9-BKT Bracket

(OPTIONAL)

-2-

Mini Phantom Head
w/Starburst LEDs

ULB9-HOOD-1 Hood
w/Windshield Brackets

ULB9-HOOD-2 Hood
w/Extra Cable Hole and
Windshield Brackets

S111-6
Hood Gasket

PLABULB9
Reflective Label

P30019-267
Pivot Brackets for
Flush Mounting ULB9S

P30047-166
Foam Flashback Gasket
for Flush Mounting ULB9S

(OPTIONAL)

ULB9S Mounting

Front Windshield Adhesive Mount

1. The hood can be installed such that the

cord can exit either side.
Route the cord through the appropriate

slot and slide the hood onto the back of
the light until the hooks on the hood
“latch” onto the light.

2. If desired, install the rubber gasket along the edge of the hood
to help reduce vibration against the window, as well as to
allow for minor adjustments to the curvature of the window.

3. Hold the light up to your windshield to test fit the best location for the light, typically high

on the windshield touching the headliner.

4. Clean and dry windshield. (clean with alcohol if necessary)

DO NOT MOUNT ON DEFROSTER LINES!!

5. Remove the tape liner from both brackets on the light.

6. Place light in the chosen location pressing firmly on the brackets ensuring maximum

contact and adhesion.

7. With the brackets in place and secure, loosen both nuts only enough to slide the light

snugly against the windshield and then retighten.

CAUTION: Take extreme caution not to over tighten the nuts!!! Over
tightening of the nuts can strip the holes and result in a faulty mount.

Because it takes about 72 hours or 3 days for the adhesive to reach full
bonding potential, check the light often during this period to ensure the
tape maintains full contact with the bracket and glass.

Light Replacement

If you need to replace your light for any reason,
you can leave the brackets affixed to the
window and remove the light from them.

1. Loosen both nuts only enough to slide the light

out of the slots in the brackets. The brackets
will remain attached to the windshield.

2. Install new light by sliding it back into place in the

bracket slots.

Note - insure square head of carriage bolt is within bracket slot.

3. Tighten both nuts. Note - Do not over tighten nuts as doing so may cause

the carriage bolt head to spin in the hood.

Bracket Removal

Over time the bracket adhesive bond becomes stronger. If the procedure below doesn't
work it may be necessary to use alcohol or WD40 to soften the adhesive in combination with
the steps below.

1. Remove the light head as described under Light Replacement.

2. Using razor blade scraper, carefully scrape the adhesive tape off the window gently

prying the bracket away from the window until it is removed.

!

-3-