WIRING INSTRUCTIONS FOR STAR SWITCH #SP3860-1
The manufacturer warrants each new product, under normal use, against factory defects in material and
workmanship for one year after the date of purchase. The owner will be responsible for returning to
the Service Cen
ter any defective item(s) with the transportation costs prepaid. The manufacturer will,
without charge,
, products, or part(s), which its inspection determines
to be defective. Repaired or replacement item(s) will be return
ed to the purchaser with transportation
costs prepaid from the service point. A copy of the purchaser's receipt must be returned with the
t limited to, bulbs, strobe tubes, domes, and/or the
finish. This warranty shall not apply to any light, which has been altered, such that in the
manufacturer's judgment, the performance or reliability has been affected, or if any damage has resulted
from
abnormal use or service. This warranty does not apply to defect or damage occurring as a result of
disaster, accident, abuse, misuse, lightning, power surges, or failure to follow instructions in any
a result of any unauthorized service or repairs
by unauthorized persons shall be excluded from this warranty.
There are no warranties expressed or implied (including any warranty of merchantability or fitness),
which extend this warranty period.
of use of the product, loss of time, inconvenience,
The
manufacturer reserves the right to change the design of the product without assuming any obligation
to modify
This warranty gives you specific legal rights. You might also have additional rights which may vary
from state to state. Some states do not allow limitations on how long an implied warranty lasts. Some
t allow the exclusion or limitation of incidental or consequential damages. Therefore, the
Lighted (ON/OFF) Switch
1. IMPORTANT: Please read all of the following instructions before installing
your new Star switch. This instruction sheet applies only to the model
listed at the top of this sheet.
2. CAUTION: All of our DC powered warning lights are polarity sensitive.
These lights are polarity protected only if the appropriate fuse is used. All
wires connected to the positive terminal of the battery should be fused at
the battery for their rated load, in addition to the fuse provided at the
switch panel. Testing the light before this fuse is properly installed
will void the warranty on the switch and light.
3. Connect the fused red wire from terminal 1 of SW1 to the positive side of
the 12VDC power through a 5, or 10 amp fuse, depending on the current
draw of the light(s) you are installing. Check the label on the warning
light(s) for proper voltage and current.
4. Connect the red wire from terminal 2 of SW1 to the red wire from your
strobe light or Star pak.
5. The black wire from terminal 3 of SW1 is the ground lead and should be
connected to a good chassis ground.
6. The black or white wire from your strobe light or strobe pak should also be
connected to a good chassis ground.
defective item(s) in order to qualify for the warranty coverage.
Exclusions from this warranty include, but are no
enclosed manuals. Any damage or defects occurring as
commercial loss or consequential damages, including costs of any labor, are not covered.
any product previously manufactured.
states do no
above limitation(s) or exclusion(s) may not apply to you.
ONE YEAR LIMITED WARRANTY
repair or replace at its option
The loss
SP3860-1 SWITCH PANEL
(REAR VIEW)
ON
3
2
1
WARNING
LIGHT
PURPLE (IF PRESENT)
RED
BLACK
OFF
BLACK
RED
10 AMP
FUSE
TO +12 VDC
CONNECT
GOOD
GOOD
CHASSIS
CHASSIS
GROUND
GROUND
GOOD
GOOD
CHASSIS
CHASSIS
GROUND
GROUND
If you have any questions concerning this or any other Star product,
please contact our Customer Service Department at (585) 226-9787.
If a product must be returned for any reason,
please contact our Customer Service Department to obtain a
Returned Goods Authorization number (RGA #) before you ship the product to Star.
Please write the RGA # clearly on the package near the mailing label.
PLITSTR120 REV. G 12/23/04
Loading...