Star Headlight & Lantern FM6908 User Manual

MODEL FM6908

ONE YEAR LIMITED WARRANTY

IMPORTANT

Chrysler Solid State 7-Pattern Isolated Headlight Flasher

Congratulations! You are now the proud owner of the most technically advanced true 100%
Solid State Selectable Pattern Headlight Flasher System in the market today. Add to it our
never ending commitment to quality, when properly installed this new Flasher System will
provide you with years of dependable trouble free service.

Operating Specifications:

•

Compatible with both 2 and 4 headlight systems with isolated high beam wires

•

10-16 VDC Input

•

Output: 9.5A per output

55 Watt Load on each output

•

High-Beam Override - Disables flasher when high-beams are activated

•

Less than 10mA standby current

Mounting:

The enclosed headlight flasher has been designed to be water resistant. However, to ensure
years of trouble free operation of the flasher system, it should be mounted in a location that is
protected from direct water spray and high temperatures.

Electrical Connections:

GREEN: Connect to reliable ground, preferably close to ground post of battery.

BLUE: Locate the wire that supplies power to the passenger side high beam. Cut the

ORANGE: Connect the flasher’s orange wire to the cut wire end from the passenger side

YELLOW: Locate the wire that supplies power to the driver side high beam. Cut the wire

GREY: Connect the flasher’s grey wire to the cut wire end from the driver side that goes

WHITE: Connect to a +10-16VDC power source capable of providing 15 Amps.

RED: Connect to a powered switch through a user supplied 1 amp fuse.

BLACK: (OPTIONAL Connection): If an “Automatic Nighttime Flasher disable” is required

Flashing Headlight and Taillight Systems are intended for use on approved
vehicles ONLY. It is the responsibility of the user of these systems to insure
compliance to any Federal, State, or Municipal regulations that may apply.

wire and connect the flasher’s blue wire to the cut wire end that goes back to the
high beam headlight.

that goes back to the vehicle’s high beam switch.

and connect the flasher’s yellow wire to the cut wire end that goes back to the
high beam headlight.

back to the vehicle’s high beam switch.

WARNING: DO NOT USE A CIRCUIT BREAKER, FUSIBLE LINK,
OR SLOW BLOW TYPE FUSE!!

(check with state and municipal regulations) simply ‘T’ or tap this wire into the
parking / marker light wire. This feature will disable the flasher whenever the
parking marker lights are turned ON.

Flash Pattern Selection:

To change the pattern, momentarily
touch and release the Red/Black
wire to ground. The pattern will

High

Beam

High

Beam

change each time Red/Black wire is
touched to ground

Final System Check:

1. Verify Headlight Flasher
properly flashes
headlights when Flash
Enable switch is activated.

2. With the Headlight Flasher
ON, activate the High
beams and verify that the
flasher de-activates and
that both high beam
headlights turn ON
steady.

Driver Side Highbeam Wire

CUT

Good

Chassis

Ground

YELLOW

GREY

W

H

E

T

I

Connect to flasher On/Off Switch

RED -

FM6908

Headlight

Flasher

Light Wire for

OPTIONAL: Connect to Parking

BLACK -

Good

Chassis

Nighttime Cut Off

Ground

BLUE

ORANGE

R

E

D

/

B

L

CUT

A

C

K

Pattern Select

Touch & Release to Ground

3. If “Automatic Nighttime Flasher
disable” is hooked up (Black
wire), test it by activating the
headlight flasher, then turning
ON the parking/marker lights.
Verify that the Flasher is

+12 VDC

automatically disabled.

FOR DODGE DURANGO OR DAKOTA INSTALLATIONS

This product requires the proper installation of the Night-Time Cutoff circuit.

Good

Chassis

Ground

GREEN

This circuit is controlled by the black wire exiting the Flasher. The black wire
must be wired according to the installation drawing and instructions. Failure to
do so may result in head damage to the vehicle’s headlamp housings at the
owner’s expense. The Headlamp Flasher will ONLY operate when the
headlamps are switched to OFF position. Whenever the headlamps are
activated, the Flasher WILL NOT function. It is the responsibility of the installer
to make certain the vehicle operator is aware of this situation.

Star Headlight & Lantern Co., Inc. warrants this flasher, under normal use, against factory defects in material and
workmanship for one year after the date of purchase. The owner will be responsible for returning to the Service Center any
defective item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or replace at its
option, products, or part(s), which i ts inspection determines to be defective. Repaired or replacement item(s) will be
returned to the purchaser with transportation costs prepaid from the service point. A copy of the purchaser's receipt must
be returned with the defective item(s) in order to qualify for the warranty coverage.

This warranty shall not apply to any flasher which has been altered, such that in the manufacturer's judgment, the
performance or reliability has been affected, or if any damage has resulted from abnormal use or service. This warranty
does not apply to defect or damage occurring as a result of disaster, accident, abuse, misuse, lightning, power surges, or
failure to follow instructions in any enclosed manuals. Any da mage or defects occurring as a result of any unauthorized
service or repairs by unauthorized persons shall be excluded from this warranty.

There are no warranties expressed or implied (including any warranty of merchantability or fitness), which extend this
warranty period. The loss of use of the product, loss of time, inconvenience, commercial loss or consequential
damages, including costs of any labo r, are not covered. The manufacturer reserves the right to change the design of
the product without assuming any obligation to modify any product previously manufactured.

This warranty gives you specific legal rights. You might also have additional rights which may vary from state to state.
Some states do not allow limitations on how long an implied warranty lasts. Some states do not allow the exclusion or
limitation of incidental or consequential damages. Therefore, the above limitation(s) or exclusion(s) may not apply to you.

Passenger Side Highbeam Wire

PLIT476 REV A 11/6/12