Star Headlight & Lantern BBK-FORD User Manual

UP = ON
BBK-FORD
Please write the RMA # clearly on the package near the mailing label.
(optional)
Ford Interceptor Steering Wheel Control Module
The new Ford Interceptor Police Package vehicles now come optionally equipped with integrated controls on the steering wheel to operate four external devices. Because these controls have a “low-current” output, most devices will require external relays that can handle a higher current. This module provides single, integrated “easy-to­install” solid-state module that connects to the vehicle’s factory-installed harness and allows the steering wheel controls to activate four 10-amp outputs.
Both ends of the harness should come with your new Ford Interceptor (may be pre­installed on the factory wired harness located under the center of the dash or may be loose).
Complete wiring & access details are available from Ford.
Mounting in the trunk near the other electronic devices is highly recommended.
The manufacturer warrants each new product against factory defects in material and workmanship for one year after the date of purchase. The owner will be responsible for returning to the Service Center any defective item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or replace at its option, products, or part(s), which its inspection determines to be defective. Repaired or replacement item(s) will be returned to the purchaser with transportation costs prepaid from the service point. A copy of the purchaser's receipt must be returned with the defective item(s) in order to qualify for the warranty coverage. Exclusions from this warranty include, but are not limited to, bulbs, strobe tubes, domes, and/or the finish. This warranty shall not apply to any light, which has been altered, such that in the manufacturer's judgment, the performance or reliability has been affected, or if any damage has resulted from abnormal use or service.
There are no warranties expressed or implied (including any warranty of merchantability or fitness), which extend this warranty period. The loss of use of the product, loss of time, inconvenience, commercial loss or consequential damages, including costs of any labor, are not covered. The manufacturer reserves the right to change the design of the product without assuming any obligation to modify any product previously manufactured.
This warranty gives you specific legal rights. You might also have additional rights that may vary from state to state. Some states do not allow limitations on how long an implied warranty lasts. Some states do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above limitation(s) or exclusion(s) may not apply to you.
Stand Alone Default Install
From Ford
Factory Harness
Make the connection to your new BBK-FORD as shown in the diagram above, ignoring the “Optional” siren inputs.
There are three Input Power terminals. Depending upon the current need for your devices, they may not all be needed. In addition, the gauge of wire run to the power input terminal will depend upon the length of the run and the current you need to supply.
When you press the buttons on the steering wheel the corresponding light output associated with that button will illuminate the indicator LED on the BBK-FORD module and the output will have battery voltage applied to it.
Each output has a maximum output of 10 amps.
WARNING: ENSURE ALL CONNECTORS ARE FULLY INSERTED & SCREWS LOCKED
ONE YEAR LIMITED WARRANTY
(no integration with siren controller)
Ford Input 4
Ford Input 3
Ford Input 2
Ford Input 1
Siren Input 4
(optional)
Siren Input 3
(optional)
Siren Input 2
(optional)
Siren Input 1
UP = ON
(optional)
NO FUNCTION FORD 4 = OUT 4 & 3 ON FORD 4 = OUT 4 & 2 ON FORD 4 = OUT 4 & 1 ON
Ground
+ VDC Battery
FB
LED
+ VDC Battery
FB
LED
FB
LED
FB
LED
Output 4
Output 3
Output 2
Output 1
+ VDC Battery
PLIT483 REV. - 9/14/12
12V BATTERY
LIGHT 4
LIGHT 3
LIGHT 2
LIGHT 1
Installation Utilizing Siren Controls
(Siren “OR” Function)
From Ford
Factory Harness
Siren Light Outputs
Ford Input 4
Ford Input 3
Ford Input 2
Ford Input 1
Siren Input 4
(optional)
Siren Input 3
(optional)
Siren Input 2
(optional)
Siren Input 1
UP = ON
(optional)
WARNING: ENSURE ALL CONNECTORS ARE FULLY INSERTED & SCREWS LOCKED
NO FUNCTION FORD 4 = OUT 4 & 3 ON FORD 4 = OUT 4 & 2 ON FORD 4 = OUT 4 & 1 ON
FB
LED
FB
LED
FB
LED
FB
LED
Ground
+ VDC Battery
+ VDC Battery
Output 4
Output 3
Output 2
Output 1
+ VDC Battery
12V BATTERY
LIGHT 4
LIGHT 3
LIGHT 2
LIGHT 1
The BBK-FORD can be used in conjunction with a siren that has light control functionality such that the connected devices can be controlled by either the steering wheel controls “OR” the siren controls.
Make the connections described on the previous page under the Stand Alone Default Install section.
Connect the light outputs from your siren to the corresponding Siren Input terminals on your BBK-FORD.
These siren inputs are feedback protected. (i.e. steering wheel activation of that output does NOT send power back through the siren input.)
Siren Control Only Lighting
Because the siren inputs are feedback protected, you can optionally connect lights to the Siren Light Outputs that will be controlled ONLY by the siren. Lights connected as shown to the right will NOT be activated by the steering wheel controls.
LIGHT 5
Siren Light Outputs
(optional)
Siren Input 4
(optional)
Siren Input 3
(optional)
Siren Input 2
(optional)
Siren Input 1
(optional)
Progressive Control DIP Switches
If you have any questions concerning this or any other product,
please contact our Customer Service Department at (585) 226-9787.
If a product must be returned for any reason, please contact our Customer Service Department to obtain
a Returned Materials Authorization number (RMA #) before you ship the product back.
There are 4 DIP switches located the BBK-FORD that will allow you to set the 4th steering wheel button to also enable light outputs 1, 2, or 3, along with 4. Note:
This will not be displayed on your vehicle cluster display.
Loading...