Page 1
INSTALLATION AND INSTRUCTION MANUAL
Model
Model
ModelModel
9016LED
Plus
™
Minibar
Due to continuous product improvements, we must reserve the right to change any specifications and information,
NOTICE
contained in this manual at any time without notice. Star Headlight & Lantern Co., Inc. makes no warranty of any
kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness
for a particular purpose. Star Headlight & Lantern Co., Inc. shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing, performance, or use of this manual.
The manufacturer warrants this LED light against factory defects in material and workmanship for five years
after the date of purchase. The owner will be responsible for returning to the Service Center any defective
item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or replace at its
option, products, or part(s), which its inspection determines to be defective. Repaired or replacement
item(s) will be returned to the purchaser with transportation costs prepa id from the service point. A copy of
the purchaser's receipt must be returned with the defective item(s) in order to qualify for the warranty
coverage. Exclusions from this warranty include, but are not limited to, domes, and/or the finish. This
warranty shall not apply to any light, which has been altered, such that in the manufacturer's judgment, the
performance or reliability has been affected, or if any damage has resulted from abnormal use or service.
There are no warranties expressed or implied (including any warranty of merchantability or fitness), which
extend this warranty period. The loss of use of the product, loss of time, inconvenience, commercial loss or
consequential damages, including costs of any labor, are not covered. The manufacturer reserves the right
to change the design of the product without assuming any obligation to modify any product previously
manufactured.
This warranty gives you specific l egal rights. You might also have additional rights that may vary from state to
state. Some states do not all ow limitations on how long an implied warranty lasts. Some states do not allow
the exclusion or l imitation of incidental or consequential damages. Therefore, the above limitation(s) or
exclusion(s) may not apply to you.
please contact our Customer Service Department at (585) 226-9787.
If a product must be returned for any reason, please contact our Customer Service Department to
obtain a Returned Material Authorization number (RMA #) before you ship the product back.
Please write the RMA # clearly on the package near the mailing label.
LED FIVE YEAR LIMITED WARRANTY
If you have any questions concerning this or any other product,
PLIT419 REV. D 10/19/12
Page 2
IMPORTANT: Please read all of the following instructions before installing your new warning light.
Permanent Mounting
1. Using the gasket as a template, mark the four
bolt holes on the mounting surface (and the
center wire hole, if you will be needing one).
2. Drill a 9/32" hole in the four marked
spots or the mounting bolts.
CAUTION: Take care not to drill
through the headliner below.
3. Insert the head of two mounting bolts
into each of the access holes found
along the slots on the bottom of the bar
and slide one to each end of the base.
Slide the heads of two mounting
bolts into each bolt access hole
along each of the two
mounting slots.
4. Route the wires through the center of the gasket and align the bolts properly BEFORE
REMOVING THE BACKING.
5. Remove the
adhesive backing
on the gasket and
carefully stick the
gasket onto the
base, over the
bolts, with the wires
routed through the
center hole.
6. Route your wires
through the
mounting surface if
applicable.
7. Install your light with the four bolts going through your mounting holes. Place a washer
and nut on each of the bolts and tighten until snug.
-1-
Page 3
Wiring for Permanent Mount Models
CAUTION: All of our DC powered warning lights are polarity sensitive. These lights are
polarity protected only if the appropriate fuse is used. All wires connected to the positive
terminal of the battery should be fused at the battery for their rated load. Testing the
light before this fuse is properly installed will void the warranty on the light.
Red - (Power) Connect to +12-24 VDC through your switch. Be sure to use a 10
Black - (Ground) Connect to the negative side of the battery.
amp fuse when connecting the switch to the positive side of the power supply.
Purple - (Optional - High/Low) Switches the light between High and Low power.
• High Power Only: Leave disconnected (cover wire with wire nut or tape)
• Low Power Only: Connect to Ground
• High/Low Switching Option: Connect to Ground through a switch
Red w/Green - (Pattern Select) Touch and release to +12-24 VDC to change patterns (see
next page).
White - (Synchronization) If you are only installing one unit, cut the White wire short and
tape the end.
Connect the white wires from both units together ONLY AFTER
PROGRAMMING them for the same pattern.
Synchronization of Multiple Lights
You can synchronize up to six lights with compatibility.
DO NOT CONNECT WHITE WIRES UNTIL PROGRAMMING HAS BEEN COMPLETED
FOR ALL LIGHTS!!
1. Power up the first unit and select a pattern.
2. Program the second light with the same Pattern.
•
The two lights will flash together (simultaneous).
•
Optionally you can program one light for Pattern 16 and the other for Pattern 17. This
will cause the lights to flash opposite one another (alternate).
3. After programming all lights, tie off the green wires and connect the white wires together.
4. Test lights by applying power to all of them at the same time.
Magnet Mounting
If you are mounting the light on the roof of your vehicle, take extreme care to ensure that
the magnet is firmly seated on your roof, and that the pull of the magnet is sufficient to
secure the light in place. Since the composition of the metal in the roofs of different
vehicles may vary, as well as the contour, texture, and/or condition, Star cannot
guarantee the ability of the light to remain in place on a moving vehicle. It is the sole
responsibility of the owner to ensure the warning light is secure.
Care should be taken when routing the cig plug cord so that it does not
interfere with the proper operation of the driver-side or passenger-side
airbag! Failure to heed this warning may result in serious or fatal injury.
-2-
Page 4
Pattern Programming
• To change patterns, press and release the Pattern Select Button
(cig plug models only) or briefly touch and release the Red w/Green
Stripe wire to +12-24VDC (hard-wired versions only).
• The cycle repeats after the last pattern.
• Pattern Shortcuts: Touch and hold the Red w/Green Stripe Wire
to +12/24VDC (or hold the Pattern Select Button) for the length of
time that corresponds to the pattern you would like to jump to.
Once you find the pattern you wish to display, connect the Pattern Select wire to ground
(hard-wire only) and deactivate the light. This will store the selected pattern.
Length of Hold Unit Blinks Shortcut to
3 seconds 1 time Pattern 1
6 seconds 2 times Pattern 6
9 seconds 3 times Pattern 11
12 seconds 4 times Pattern 16
Flash
Pattern
Pattern
Type
#
1 K
2 L Al ternating Fast Doubleflash Alternating Fast Doubleflash
3 M Alternating Tripleflash Alternating Tripleflash
4 N Al ternating PSU Flicker Alternating PSU Flicker
5 O Alternating PSU Random Alternating PSU Random
6 F Alternating Quadflash †† Alternating Quadflash ††
7 G Alternating Quadflash w/Post-Pop Alternating Quadflash w/Post-Pop
8 H Al ternating Singleflash Alternating Singleflash
9 I Alternating Doubleflash Alternating Doubleflash
10 J Alternating Variable Alternating Variable
11 P
12 Q Swing Alternating Random
13 R Alt. Fast Doubleflash, Alt. Flicker Alternating Quintflash
14 S Alt. Quad, Alt. Flicker, Alt. Double, Fli cker Alt. Fast Doubleflash, Alt. Flicker
15 T Counter Clockwise Rotating Flash Alt. Quad, Alt. Flicker, Alt. Double, Flicker
16 G
17 G Sim. Quad w/Post Pop (Phase 2) Sim. Quad w/Post Pop (Phase 2)
18 U
19 V Steady burn one side, Other side Single Flash Steady burn one side, Other side Single Flash
20 NONE Cycle All Cycle All
Patterns for ALL Colors
Except For Amber
Alternating Flicker † Alternating Flicker †
Alternating Quintflash †††
Sim. Quad w/Post Pop (Phase 1) †††† Sim. Quad w/Post Pop (Phase 1) ††††
Alt. Triple, Alt. Non-Synch Double, Alt. Quint,
Flicker
† = Programming Shortcuts 1, 2, 3, and 4 (see table above)
Patterns for Amber Lights
Alternating Post Pop
Alt. Triple, Alt. Non-Synch Double, Alt. Quint,
Flicker
Please Note: These instructions are provided as a general guideline only. Specific
mounting, wiring, and/or weather-sealing may be necessary and are the sole
responsibility of the installer. Star Headlight & Lantern Co., Inc. assumes no
responsibility for the integrity of the installation for this or any of its products.
-3-
Loading...